Résumé du contenu de la page N° 1
MODEL G0709
14" x 40" GUNSMITHING LATHE
OWNER'S MANUAL
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
Résumé du contenu de la page N° 2
This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death. The owner of this machine/tool is solely responsible for its safe use. This responsibility includes but is not limited to
Résumé du contenu de la page N° 3
Table of Contents INTRODUCTION ............................................... 2 SECTION 6: MAINTENANCE ......................... 53 SECTION 1: SAFETY ....................................... 7 SECTION 7: SERVICE ................................... 59 SECTION 2: POWER SUPPLY ...................... 10 SECTION 3: SETUP ....................................... 12
Résumé du contenu de la page N° 4
INTRODUCTION Manual Accuracy Contact Info your machine may not exactly match the manual Machine Description www.grizzly.com
Résumé du contenu de la page N° 5
Identification Figure 1.
Résumé du contenu de la page N° 6
Machine Data Sheet MACHINE DATA SHEET Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901 MODEL G0709 14 X 40 GUNSMITH'S GEARHEAD LATHE Weight............................................................................................................................................................ 1300 lbs. Length/Width/Height...............................................................................................................71-1/2 x 26-3/16 x 52
Résumé du contenu de la page N° 7
Spindle Bore.........................................................................................................................................1-9/16 in. Spindle Taper.............................................................................................................................................MT#5 No Of Spindle Speeds.......................................................................................................................................8 Spindle Speeds.........
Résumé du contenu de la page N° 8
NSK precision tapered roller spindle bearings Flame hardened headstock gears Induction-hardened and precision ground cast iron bed Coolant system Adjustable halogen work light Foot brake with motor shut-off switch Full-length splash guard Pull-out chip tray 200-Series quick-change tool post Outboard spindle spider mount with 4 brass-tipped screws Cast iron cabinet stands Fully-enclosed quick-change gearbox Tailstock offset V-slide with wrench locking socket D1-5 Camlock Spindle 6" 3-Jaw chuck
Résumé du contenu de la page N° 9
SECTION 1: SAFETY For Your Own Safety, Read Instruction Manual Before Operating this Machine The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words intended to convey the level of impor- tance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures. Indica
Résumé du contenu de la page N° 10
DISCONNECTING POWER SUPPLY. FORCING MACHINERY. GUARDS & COVERS. APPROVED OPERATION. NEVER STAND ON MACHINE. STABLE MACHINE. DANGEROUS ENVIRONMENTS. AWKWARD POSITIONS. ONLY USE AS INTENDED. USE RECOMMENDED ACCESSORIES. UNATTENDED OPERATION.
Résumé du contenu de la page N° 11
Additional Safety for Metal Lathes CLEARING CHIPS. SAFE CLEARANCES. CHUCK KEY SAFETY. REMOVING/INSTALLING CHUCKS. TOOL SELECTION. SECURING WORKPIECE. SPEED RATES. STOPPING SPINDLE BY HAND. CRASHES. LONG STOCK SAFETY.
Résumé du contenu de la page N° 12
SECTION 2: POWER SUPPLY Availability Circuit Requirements for 220V Nominal Voltage .............................. 220V/240V Cycle ..........................................................60 Hz Phase .................................................... 1-Phase Circuit Rating ...................................... 15 Amps Plug/Receptacle ............................. NEMA 6-15 Cord .........3-Wire, 14 AWG, 300VAC, “S”-Type Electrocution, fire, o
Résumé du contenu de la page N° 13
Grounding Instructions GROUNDED 6-15 RECEPTACLE Extension Cords 6-15 PLUG Figure 2. Serious injury could occur if you connect the machine to power before completing the setup proces
Résumé du contenu de la page N° 14
SECTION 3: SETUP Items Needed for This machine presents Setup serious injury hazards to untrained users. Read through this entire manu- al to become familiar with the controls and opera- tions before starting the Description Qty machine! Wear safety glasses dur- ing the entire setup pro- cess! Unpacking This machine and its com- ponents are very heavy. Use power lifting equip- ment such as a fork lift or
Résumé du contenu de la page N° 15
Inventory Mounted Inventory Components Qty A. B. C. D. Loose Inventory Components Qty E. F. Figure 3. G. H. I. Toolbox Inventory Components Qty J. K. L. M. N. O. P. Q. R. S. T. Figure 4. U. V. W. X. Y. NOTICE Some hardware/fasteners on the inventory list may arrive
Résumé du contenu de la page N° 16
Hardware Recognition Chart
Résumé du contenu de la page N° 17
Site Considerations Weight Load Physical Environment Machine Data Sheet Space Allocation Electrical Installation See below for required space allocation. Lighting Children or untrained people may be seriously injured by this machine. Only install in an access restricted lo
Résumé du contenu de la page N° 18
Cleanup Gasoline or products with low flash points can explode or cause fire if used to clean machin- ery. Avoid cleaning with these products. Many cleaning solvents are toxic if concentrat- ed amounts are inhaled. Only work in a well-venti- lated area. NOTICE Avoid chlorine-based solvents, such as acetone or brake parts cleaner, that may Before cleaning, gather the
Résumé du contenu de la page N° 19
Additional Cleaning Tips Lifting & Moving H8257—Primrose Armor Plate with Moly-D Machine and Way Oil 1 Quart You must use power lifting equipment and assistance to lift and move this machine. Inspect all lifting equipment to make sure it is in working order and rated for the load before attempting to lift. Ignoring this warn- ing may lead to serious personal injury or death. Figure 8
Résumé du contenu de la page N° 20
Using Machine Mounts Mounting Figure 10 Bolting to Concrete Floors Figure 9 Figure 10 NOTICE We strongly recommend securing your machine to the floor if it is hardwired to the power source. Consult with your electrician to ensure compliance with local codes. NOTICE Most electrical codes require that machines connected to the power source by fixed
