Résumé du contenu de la page N° 1
ElEctric clippEr
Model 47082
SEt up And OpErA ting inStructiOnS
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
distributed exclusively by Harbor Freight t ools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
read this material before using this product.
Failure to do so can result in serious injury.
SAVE tHiS MAnuAl.
© ®
Copyr
Résumé du contenu de la page N° 2
SpEciFicA tiOnS High impact plastic housing, Construction High Carbon steel cutting blade Comb Attachment (w/ 4 Settings) Barber Comb E316219 Accessories Cleaning Brush Scissors Lubricant (One Tube) Electrical Input 120 V~, 60 Hz, 8-13 W Save this Manual You will need this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures, parts list and assembly diagram. Keep your invoice with this manual. Write the invoice number on the in
Résumé du contenu de la page N° 3
4. never operate this appliance if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the appliance to a service center for examination and repair. 5. keep the cord away from heated surfaces. 6. never operate the appliance with the air openings blocked or while on a soft surface, such as a bed or couch, where the air openings may be blocked. Keep the air openings free of lint, hair, and the like. 7. never drop or i
Résumé du contenu de la page N° 4
unp Acking When unpacking, check to make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. OpErA tiOn inStructiOnS blade Alignment • The Clipper comes oiled and aligned from the factory. Blades must be realigned after they have been removed for cleaning or replacement. 1. To realign blades, match the upper and lower blades teeth up, point for point. The end
Résumé du contenu de la page N° 5
• Before turning the Clipper off, rapidly move the Blade Lever from close cut to longer cut twice. This will clear trimmings from the Clipper. cutting Hair Attachment Comb #1 leaves 3mm (1/8 inch) hair length. Attachment Comb #2 leaves 6mm (1/4 inch) hair length. Attachment Comb #3 leaves 9mm (3/8 inch) hair length. Attachment Comb #4 leaves 12mm (1/2 inch) hair length. • The Comb’s sizes are marked on the outside middle surface. To apply a Comb, hold it with the teeth upwards and slide it o
Résumé du contenu de la page N° 6
8. Change to Comb #3 or #4 and, working upwards, cut the hair on the back and top of the head (see diagram 2 & diagram 3). 9. Using Comb #3 or #4, cut hair on top of head from back to front, against the direction in which the hair normally grows. In some cases, this may require changing direction (see diagram 4). 10. Comb #1 or #2 can be used to achieve very close “crew” cuts. 11. For longer hair, use the provided comb to lift the hair away from the top of the head. Cut over the comb with
Résumé du contenu de la page N° 7
13. To cut the sideburns, change Comb to #1 or #2. To produce a clean, straight line for the sideburns, reverse the Clipper by turning the bottom side upwards (see diagram 7). 14. Press the Clipper at a right angle to the head, with the tips of the blades lightly touching the skin and work downwards to obtain a clean, razor-like cut. 15. Comb through hair to check for uneven strands and ensure an even cut. Short tapered styles 1. Starting with Comb #4, cut from the back of the head to the to
Résumé du contenu de la page N° 8
plEASE rEAd tHE FOllOWing cArEFully tHE MAnuFActurEr And/Or diStribut Or HAS prOVidEd tHE p ArtS liSt And ASSEMbly diAgrAM in tHiS MAnuAl AS A rEFErEncE t OOl Only. nEitHEr tHE MAnuFActurEr Or diStribut Or MAkES Any rEprESEnt AtiOn Or WArrAnty OF Any kind t O tHE buyEr tHA t HE Or SHE iS quAliFiEd t O MAkE Any rEp AirS t O tHE prOduct, Or tHA t HE Or SHE iS quAliFiEd t O rEplAcE Any p ArtS OF tHE prOduct. in FAct, tHE MAnuFActurEr And/Or diStribut Or ExprESSly St AtES tHA t All rEp AirS
