Résumé du contenu de la page N° 1
HEAT GUN
WITH ACCESSORIES
47269
ASSEMBLY & OPERATING INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
TO PREVENT SERIOUS INJURY,
READ AND UNDERSTAND ALL WARNINGS
AND INSTRUCTIONS BEFORE USE.
© ®
Copyright 2002, 2004 by Harbor Freight Tools . All rights reserved. No
portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
For technical q
Résumé du contenu de la page N° 2
THANK YOU for choosing a HARBOR FREIGHT TOOLS product. For future reference, please complete the owner’s record below: Model___________ Serial No._____________ Purchase Date_____________ Save This Manual You will need the manual for the safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts list and diagram. Keep your invoice with this manual. Write the invoice number on the inside of the front cover. Keep the manual and invoice in a safe and dry
Résumé du contenu de la page N° 3
electrician if you are in doubt as to whether the outlet is properly grounded. If the tools should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user. 5. Double insulated tools are equipped with a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician
Résumé du contenu de la page N° 4
TOOL USE AND CARE 16. Use clamps (not included) or other practical ways to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control. 17. Do not force the tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed. 18. Do not use the power tool if the Power Switch does not turn it on or off. Any tool that cannot be controlled with
Résumé du contenu de la page N° 5
Heat Gun Specific Safety Rules Important Safety Instructions Read These Instructions WARNING: Extreme care should be taken when stripping paint. The peelings, residue and vapors of paint may contain lead, which is poisonous. Any pre-1977 paint may contain lead and paint applied to homes prior to 1950 is likely to contain lead. Once deposited on surfaces, hand to mouth contact can result in the ingestion of lead. Exposure to even low levels of lead can cause irreversible brain and nervous sys
Résumé du contenu de la page N° 6
Nozzle is extremely hot. When using the Heat Gun, never allow any body part to contact nozzle. Never touch any hot surface when the Heat Gun is running. Be careful to put the hot Heat Gun down only on a non-flammable surface. Never use heat Gun as a blow dryer. Never direct heat flow to any person or animal. Do not obstruct the airflow. Do not cover air outlet at any time. Do not put anything down on the nozzle. Additional Warnings and Safety Instructions Hidden areas such as behind walls,
Résumé du contenu de la page N° 7
FIGURE B FIGURE A DOUBLE INSULATED TOOLS: TOOLS WITH TWO PRONG PLUGS 4. Tools marked “Double Insulated” do not require grounding. They have a special double insulation system which satisfies OSHA requirements and complies with the applicable standards of Underwriters Laboratories, Inc., the Canadian Standard Association, and the National Electrical Code. (See Figure B.) 5. Double insulated tools may be used in either of the 120 volt outlets shown in the following illustration. (See Figure B.)
Résumé du contenu de la page N° 8
EXTENSION CORDS 1. Grounded tools require a three wire extension cord. 2. As the distance from the supply outlet increases, you must use a heavier gauge extension cord. Using extension cords with inadequately sized wire causes a serious drop in voltage, resulting in loss of power and possible tool damage. (See Figure C.) 3. The smaller the gauge number of the wire, the greater the capacity of the cord. For example, a 14 gauge cord can carry a higher current than a 16 gauge cord. (See Figure C.
Résumé du contenu de la page N° 9
The Heat Gun and included accessories are designed to be used to remove paint from painted surfaces. Never use the Heat Gun with chemical strippers. Other Uses for the Heat Gun 1) Shrink plastic wire nuts and other wire jointers for tight fits. 2) Remove self-adhesive trim and stickers. 3) Wax and remove wax from surfboards, skis, and snowboards. 4) Use with PVC shrink wrap sheeting for extra bonding power. 5) Thaw frozen pipes and locks. Do not use on plastic pipe! 6) Dry out damaged timber or
Résumé du contenu de la page N° 10
Step 2) Select the desired and appropriate attachment for the Heat Gun. Slide the attachment onto the Nose Cone (32) -see Figure D, previous page. Step 3) Turn on the Heat Gun. The Heat Gun has a High setting, a Low setting and an OFF Setting. Push the Switch (2) in at “H” (top of Switch) for the High setting or at “L” (bottom of Switch) to run on the low setting. Allow it to reach full power and full heat. Step 4) Hold the Nose Cone (32) with attachment 3" to 4" from the surface and/or mat
Résumé du contenu de la page N° 11
Unpacking When unpacking your Heat Gun in Blowmold Case, check to make sure the following parts are included. If any parts are missing or broken, please call HARBOR FREIGHT TOOLS at 1-800-444-3353. Parts List 1 Left Housing 1 25 Heating Wire 1 2 Switch 1 26 Ceramic Tube 1 3 Shock Proof Pad 2 27 Washer 1 4 Diode 4 28 Connector Piece 3 5 Motor 1 29 Mica Paper 1 6 Tapping Screw 2 30 Air Duct 1 7 Screw 2 31 Air Locking Ring 1 8 Fan 1 32 Nose Cone 1 9 Tapping Screw 3 33 Tapping Screw 1 10 Vent VRI 1
Résumé du contenu de la page N° 12
PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAK
