Résumé du contenu de la page N° 1
TRINITRON COLOR VIDEO MONITOR
®
BVM-20F1U/20F1E
BVM-20E1U/20E1E
BVM-14F1U/14F1E
BVM-14E1U/14E1E
BVM-14F5U/14F5E
BVM-14E5U/14E5E
[English]
OPERATION MANUAL
1st Edition (Revised 7)
Serial No. 2000001 and Higher
Résumé du contenu de la page N° 2
CAUTION: WARNING Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the To prevent fire or shock hazard, do not manufacturer’s instructions. expose the unit to rain or moisture. ATTENTION To avoid electrical shock, do not open the Il y a un risque d’explosion si la pile est mal insérée. cabinet. Refer servicing to qualified Remplacer la pile uniquement par une pile de même ty
Résumé du contenu de la page N° 3
WARNING: THIS WARNING IS APPLICABLE FOR USA Note ONLY. Be sure to use the supplied power cord for this monitor, or this monitor may not conform with the FCC Rules or EEC If used in USA, use the UL LISTED power cord specified Directive 89/336/EEC. below. Remarque DO NOT USE ANY OTHER POWER CORD. Utiliser le cordon d’alimentation fourni pour ce moniteur, Plug Cap Parallel blade with ground pin sinon il pourrait ne pas être conforme aux règles FCC ou à la (NEMA 5-15P Configuration) directive CEE 89
Résumé du contenu de la page N° 4
For the customers in Europe This product with the CE marking complies with both the EMC Directive (89/336/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community. Compliance with these directives implies conformity to the following European standards: • EN60950: Product Safety • EN55103-1: Electromagnetic Interference (Emission) • EN55103-2: Electromagnetic Susceptibility (Immunity) This product is intended for use in the following Electromagnetic Enviro
Résumé du contenu de la page N° 5
Table of Contents Precaution.................................................................................................. 3 Chapter 1 Overview Overview .................................................................................................... 4 Features ............................................................................................... 4 Options ................................................................................................ 5 Connector Panel Configur
Résumé du contenu de la page N° 6
Table of Contents Setting the Screen Display — ON SCREEN SET Menu..................... 44 Chapter 2 Overview ........................................................................................... 44 Menus (Continued) Structure of the SET UP Menu [C] / ON SCREEN SET Menu [C5] ............................................................................... 44 Constituent Menus of the SET UP / ON SCREEN SET Menu ......... 44 Convergence Adjustments — ALIGNMENT Menu ............................
Résumé du contenu de la page N° 7
Chapter 1 Overview Chapter 1 Overview Precaution On safety On repacking •Operate the unit only with a power source as Do not throw away the carton and packing materials. specified in “Specifications” section. They make an ideal container which to transport the • The nameplate indicating operating voltage, power unit. When shipping the unit to another location, consumption, etc., is located at the rear. repack it as illustrated on the carton. • Should any solid object or liquid fall into the c
Résumé du contenu de la page N° 8
Chapter 1 Overview Overview Setup and adjustment with the monitor The BVM-20F1U/20F1E/20E1U/20E1E, BVM- 14F1U/14F1E/14E1U/14E1E and BVM-14F5U/ memory card ®1) 14F5E/14E5U/14E5E Trinitron Color Video You can use an optional BKM-12Y Monitor Memory Card to save and load monitor setup and adjustment Monitors are high-performance 20- and 14-inch color video monitors. They are suitable for television data. If your system includes more than one monitor, stations or video production houses, where prec
Résumé du contenu de la page N° 9
Chapter 1 Overview Other features BKM-14L Auto Setup Probe •Compatible with the ISR (Interactive Status This probe allows automatic adjustment of this Reporting) system. monitor’s color temperature. •Has both RS-485 serial remote and relay contact parallel remote control connectors. For screen •Built-in safe area display and test signal generator for crosshatch, 100% white signal, 20% gray signal, gray BKM-33H20 Monitor 16:9 Mask scale, and PLUGE (Picture Line Up Generating Adapts the BVM-20F1U
Résumé du contenu de la page N° 10
Chapter 1 Overview Overview BKM-24N NTSC Decoder Adaptor Decoder and input expansion adaptors Includes a decoder for analog composite NTSC signals and input/output connectors for six analog channels. The input connector panel is configured by sliding The input signal type for each connector is set with the optional decoder adaptors and/or input expansion INPUT CONFIGURATION menu, in accordance with adaptors into input option slots at the rear of the the configuration of the connector panel. mon
Résumé du contenu de la page N° 11
Chapter 1 Overview Connector Panel Configuration The monitor comes standard with connectors for one Notes channel of Y/R–Y/B–Y or RGB. By adding optional •Only one BKM-22X board can be installed in the decoder adaptors and/or input expansion adaptors, the monitor together with either the BKM-20D or the input/output connector panel can be assembled in a BKM-21D. wide variety of configurations. • The BKM-20D, BKM-21D, and BKM-22X can not The signals that each of the adaptors’ connectors provide
Résumé du contenu de la page N° 12
Chapter 1 Overview Overview Decoder adaptor priority The table on the right shows which decoder adaptor Input signal type Decoder adaptor and format will be selected preferentially when more than one BKM- BKM- BKM- BKM- 24N 25P 27T 21D decoder adaptor which can accept the NTSC or PAL signal format have been installed in the monitor. Composite NTSC 1 3 2 signal PAL 1 3 2 For example, when a BKM-24N and a BKM-27T are Y/C NTSC 1 2 installed and an NTSC signal is selected, the NTSC signal PAL 1 2 s
Résumé du contenu de la page N° 13
Chapter 1 Overview Location and Function of Parts Front Panel BVM-14F5U/14F5E/14E5U/14E5E 1 Tally lamp 2 POWER switch 0 SHIFT button 3 DEGAUSS button 4 Numeric keypad !¡ Function buttons 5 MANUAL adjustment buttons and knobs !™ Monitor Memory 6 Menu operation Card slot buttons !£ OPTION connector 7 POWER lamp 8 STANDBY lamp 9 OVER LOAD lamp BVM-20F1U/20F1E/20E1U/20E1E/14F1U/14F1E/14E1U/14E1E 1 Tally lamp !£ OPTION connector 7 POWER lamp 8 STANDBY lamp 9 OVER LOAD lamp (Illustration: BVM-20F1U/2
Résumé du contenu de la page N° 14
Chapter 1 Overview Location and Function of Parts This manual explains the location and function of parts Channel number entry method: and controls using the control panel of the BVM- (In the explanation below, x represents any digit 14F5U/14F5E/14E5U/14E5E. The explanation applies between 1 and 9, and y represents any digit between to BVM-20F1U/20F1E/20E1U/20E1E/14F1U/14F1E/ 0 and 9.) 14E1U/14E1E with the BKM-10R/11R Monitor When selecting a channel number from 1 to 9, press Control Unit. the
Résumé du contenu de la page N° 15
Chapter 1 Overview 6 Menu operation buttons MENU button: Press to display the Menus. UP MENU UP/DOWN buttons: Press to select the DOWN ENTER items and setting values. ENTER button: Press to confirm the items and values entered (Ent button on the numeric keypad 4 has the same function). For details of menu operation, see “Basic Menu Operations” on page 22. 7 POWER lamp Lights when the monitor is put into operation mode from standby mode (see STANDBY lamp 8) by pressing the POWER switch 2. Note W
Résumé du contenu de la page N° 16
Chapter 1 Overview Location and Function of Parts 0 SHIFT button !¡ Function buttons Press to select one of the two functions designated to Change the operation conditions for the monitor. the function buttons !¡. Each time the button is pressed, the LED turns on and Each time the SHIFT button is pressed, the LED turns turns off, and the operation conditions are changed. on (SHIFT ON: lit in orange) and off (SHIFT OFF: lit Each button has two functions. Select one of the two in green). function
Résumé du contenu de la page N° 17
Chapter 1 Overview SHIFT ON (LEDs of function buttons in orange) 16:9 button: When this button is pushed in (ON), the aspect ratio changes to 16:9, and when set to OFF, the aspect ratio changes to 4:3. SYNC button: When this button is pushed in (ON), the monitor synchronizes to the sync signal input to the SYNC connectors on the rear panel (EXT SYNC). When set to OFF, it synchronizes to the sync signal included in the signals being monitored (INT SYNC). Notes • When INT SYNC is selected, use a
Résumé du contenu de la page N° 18
Chapter 1 Overview Location and Function of Parts !™ Monitor Memory Card slot Notes Insert the BKM-12Y Monitor Memory Card Do not eject the monitor memory card while data is (optional). being saved or loaded. For details of operations on monitor memory card data, see “Monitor Memory Card Data Operations — MEMORY CARD menu” on page 51. Proceed as illustrated to insert and eject the BKM-12Y Monitor Memory Card. To insert the BKM-12Y Monitor Memory Card Monitor memory card insertion slot Caution P
Résumé du contenu de la page N° 19
Chapter 1 Overview Rear Panel 6 Analog input/output connectors 7 Input option slots 8 REMOTE 1 connectors and TERMINATE switch 9 REMOTE 2 connector 1 MAIN POWER switch 2 AC IN connector !º ISR connector 3 Fuse 4 Deflection option slot 5 CONTROL UNIT connector (not provided on BVM- 14F5U/14F5E/14E5U/ 14E5E) (Illustration: BVM-20F1U/20F1E/20E1U/20E1E) 3 Fuse 1 MAIN POWER switch When turned on, the monitor enters standby mode. By Use a T4AH fuse. a setting in the SYSTEM CONFIGURATION menu, the mo
Résumé du contenu de la page N° 20
Chapter 1 Overview Location and Function of Parts 6 Analog input/output connectors 8 REMOTE 1 connectors (female, D-sub 9-pin), and TERMINATE switch ANALOG REMOTE 1 IN Y/G Y/G connectors (BNC) OUT IN REMOTE 1 IN connector IN B–Y/B connectors (BNC) B-Y/B OUT TERMINATE ON IN TERMINATE switch OFF R-Y/R R–Y/R connectors (BNC) OUT IN SYNC SYNC connectors (BNC) OUT REMOTE 1 OUT connector OUT RGB signals, component signals (Y, R–Y, and B–Y), These are RS-485 serial interface connectors, used for or c
