Résumé du contenu de la page N° 1
Note: specifications are subject to change without notice or obligation.
CONTENT
F.C.C. statement
Important safeguards
Chapter 1 Introduction
1.1 General Information..................................................................
1
1.2 Features.....................................................................................
1
1.3 Checking List.............................................................................
1
Chapter 2 Installation
2.1 Install and uninstall the pedestal .....
Résumé du contenu de la page N° 2
FEDERAL COMMUNICATIONS COMMISSION(F.C.C) STATEMENT This equipment has been tested and found to comply with the limits of a Class B digital device,pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communicati
Résumé du contenu de la page N° 3
IMPORTANT SAFEGUARDS Warnings: 1. Read all of these instructions Save these instructions for later use, Please. 2. Unplug this monitor from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 3. Do not use attachments not recommended by the monitor manufacturer as they may cause hazards. 4. Do not use this monitor near water. For example near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimm
Résumé du contenu de la page N° 4
Chapter 1 Introduction 1.1 General Information This monitor is a high-performance intelligent multi-scan TFT LCD color monitor. User friendly interface --- the easy and precise OSD control of multi- key button. Brief appearance --- elegant and compact housing. Footprint of all round tilting range --- employing sectional positioning ,well Balanced in adjustment. Analog input, plug and play facilities --- to accept RGB signal, with modulated Frame rate control allowing over 20 different input f
Résumé du contenu de la page N° 5
Chapter 2 Installation 2.1 Install and uninstall the pedestal To attach the base to your monitor, please following the steps for installation of the pedestal as below: step 1 step 2 step 3 2.2 Connect your monitor to computer 2.2.1 Turn off your computer and unplug its power cable. 2.2.2 Connect the signal cable to the video port on the back of your computer. 2.2.3 Connect the power cable for your monitor. ( to AC power jack) 2.2.4 Connect one end of the audio cable on the back of the connec
Résumé du contenu de la page N° 6
Chapter 3 Overview of your monitor 3.1 CONTROL 1.Select Button For VGA mode (1) To choose which function you need. You may choose counterclockwise or " " " " Clockwise. (2) Executing it directly lowers or raises the volume. 2. MENU Button (1) Press it to enter into MENU status. (2) Under OSD mode, press it to enter. 3.Power indicator Indicates the operating state. ( ) 4.Power Button Use this button to turn the monitor on and off. 5.AUTO Button Press it t
Résumé du contenu de la page N° 7
Chapter 4 OPERATION Direct - Access Features 4.1 SWITCHING THE MONITOR ON/OFF This ON/OFF button is used for switching the monitor on and off. Note: The ON/OFF switch does not disconnect the device from the mains voltage. To completely disconnect the mains voltage. Please remove the power plug from the socket. 4.2 POWER INDICATOR This indicator lights up green or blue when the monitor operates normally. If the monitor is in power saving mode, this indicator change to orange. when monitor is
Résumé du contenu de la page N° 8
Chapter 4 OPERATION Direct - Access Features 4.5 OSD MENU 1. Main menu OSD main menu of controls gives you an overview of the selection of controls available. When you want to make adjustment of the screen image, press and release button Menu 2. OSD Adjustment You can choose where you would like OSD image to appear on your screen. H-Position : To move the OSD image horizontally left or right. V-Position : To move the OSD image vertically up or down. Exit : or To exit the sub menu 3. Lang
Résumé du contenu de la page N° 9
Chapter 4 OPERATION Direct - Access Features or 6. Color Select Color Select Menu COOL WARM Select user mode or User color you can adjust to individual color gum intensity by yourself. Increase or decrease red. green or blue depending upon which color is selected . Cool This control adjusts the color temperature of the screen image. This item are preset by factory , you can not adjust these setting. The performance is bluer and brighter. Warm The performance is redder and closer to paper whit
Résumé du contenu de la page N° 10
Chapter 4 OPERATION Direct - Access Features 4.6 Preset Modes Timing Chart V ertical Item Addressability Freq.(Hz) 1 x 60 640 480 x 2 640 480 66 x 3 640 480 72 x 4 640 480 75 x 5 640 350 70 x 6 720 400 70 x 800 600 60 7 800 x 600 72 8 9 x 800 600 75 1024 x 768 60 10 x 11 1024 768 70 12 1024 x 768 75 15": 1-12 7
Résumé du contenu de la page N° 11
Chapter 5 Technical Information 5.1 Signal connector pin assignment PIN Signal (D-sub) PIN Signal (D-sub) 1 Red 9 +5V Input No connection 2 Green 10 Ground 3 Blue 11 Ground 4 Ground 12 SDA (FOR DDC) 5 Self Test 13 H. Sync 6 Red Ground 14 V. Sync 7 Green Ground 15 SCL (FOR DDC) 8 Blue Ground 5 1 6 10 15 11 15-Pin mini D-Type male connector 5.2 Visual Inspection Permanently unlit or lit pixels The standard of production techniques today cannot guarantee an absolutely fault- f
Résumé du contenu de la page N° 12
Chapter 5 Technical Information 5.3 Trouble shooting Before calling for service , check the information in this section to see if you can remedy any problems by yourself. If you need assistance, please call the dealer where you purchased the LCD monitor. There is no SCREEN image Please check these items: The power cord is securely connected the monitor, the adaptor, and the wall outlet. Check the signal cable connection between the monitor and the computer. Adjust
