Instruction d'utilisation Life Fitness 95T

Résumé du contenu de la page N° 1

95T Treadmills
Assembly Instructions

Résumé du contenu de la page N° 2

Congratulations... and welcome to the world of The following Parts Identification Listing and the step by step assembly procedures have been assembled to make the set-up of this treadmill as quick and easy as possi- ble. Please take special note of the following important points prior to choosing a location and beginning assembly of the treadmill… IMPORTANT SAFETY INSTRUCTIONS ! DO NOT position the rear of the treadmill within 6.5 feet ( 2 meters ) of the nearest obstruction. It is recommended

Résumé du contenu de la page N° 3

TOOLS REQUIRED FOR ASSEMBLY... #2 Phillips screwdriver; 4mm, 5mm, 8mm Allen Head Drivers (T-Bar recommended) PARTS DESCRIPTION 1 UPRIGHT Qty: 1 2 M12 x 1.75 HEX BUTTON HEAD SCREW Qty: 12 0017-00101-1984 3 M12.5 WASHER Qty: 12 4 UPRIGHT Qty: 1 0017-00104-0489 5 HANDRAIL/BRIDGE ASSEMBLY Qty: 1 6 CONSOLE BRACKET Qty: 1 7 M6 x 14 BUTTON HEAD SCREW Qty: 62 8 M6.5 WASHER Qty: 11 0017-00101-1953 0017-00104-0488 9 MASTER WIRE HARNESS Qty: 1 10 TOP COVER Qty: 1 11 RIGHT INNER HANDRAIL COVER Qty: 1 12

Résumé du contenu de la page N° 4

IMPORTANT! DO NOT DISCARD THE SHIP KIT LOCATED ON TOP OF THE DECK AND BELT. ALL NECESSARY COMPONENTS NEEDED TO COMPLETE THE INSTALLATION ARE LOCATED IN THE SHIP KIT. NE JETEZ PAS LE KIT D'EXPÉDITION PLACÉ SUR LE DESSUS DU PLATEAU ET SUR LE TAPIS. IL CONTIENT TOUS LES ÉLÉMENTS NÉCESSAIRES POUR L'INSTALLATION. IMPORTANT! CHECK THE BELT EDGE UNDER THE TREADMILL TO VERIFY THE BELT DOES NOT INTERFERE WITH LIFE- SPRING BRACKETS AND THE BELT IS PROPERLY SET WITHIN THE BELT GUIDES. 1. Remove the six SCR

Résumé du contenu de la page N° 5

8. Secure the ERGO CROSSBAR of the HANDRAIL/BRIDGE ASSEMBLY (5) to the CONSOLE BRACKET (6) using three 31 8 SCREWS (31) and three WASHERS (8). 5 NOTE: ROUTE THE HEART RATE CABLES (L) UNDER THE MOUNTING TABS AS SHOWN BELOW. BE CARE- FUL NOT TO DAMAGE THE HEART RATE CABLES. 9. From under the HANDRAIL/BRIDGE ASSEMBLY (5), install the MASTER WIRE HARNESS (9) to the CON- SOLE (D) and HEART RATE (L) CABLES. WIRE-TIE (M) the cables to the CONSOLE BRIDGE as shown. Feed the combined connector upward to t

Résumé du contenu de la page N° 6

7 14. Locate the BOTTOM COVER (13). Remove the ACCESS DOOR (N) and set it aside. Drop the POLAR CABLE (O) through the opening. Install the BOTTOM COVER to the 5 HANDRAIL/BRIDGE ASSEMBLY (5) using twelve 10 SCREWS (7). Connect the POLAR CABLE to the con- nector located under the CONSOLE BRIDGE. Tighten the SCREWS securely. NOTE: BE SURE THE BOTTOM COVER FULLY SEATS INTO THE ERGO CROSSBAR GASKETS. N NOTE: BE SURE THE BOTTOM COVER IS FULLY SEATED TO THE TOP COVER AND ARMS. 15. Attach the FRONT NECK

Résumé du contenu de la page N° 7

21. Install the LEFT REAR ENDCAP (21) using two SCREWS (22).Tighten the SCREWS securely. Do not overtighten the SCREWS. NOTE: BE SURE THE LOCATOR CLIP IS ENGAGED TO THE LEFT SIDE EXTRUSION AS SHOWN IN THE DETAIL BELOW. 22. Install one FOAM STRIP (24) between the LEFT SIDE RAIL and LEFT SIDE EXTRUSION. Repeat to install the RIGHT SIDE EXTRUSION (25) to the RIGHT SIDERAIL (U). NOTE: BE SURE THE TREADMILL IS IN THE FINAL LOCATION FOR USE BEFORE INSTALLING THE LEFT AND RIGHT EXTRUSIONS. 23. Install

Résumé du contenu de la page N° 8

IMPORTANT! CHECK THE BELT EDGE UNDER THE TREADMILL TO VERIFY THE BELT DOES NOT INTERFERE WITH LIFE- SPRING BRACKETS AND THE BELT IS PROPERLY SET WITHIN THE BELT GUIDES. Physical Dimensions: Length 80 inches / 203 centimeters Width 37 inches / 94 centimeters Height 62.25 inches / 158 centimeters Weight 95Ti: 450 pounds / 204 kilograms 95Te: 455 pounds / 206 kilograms Step-up Height: 9.5 inches / 24 centimeters PRE-OPERATION CHECKLIST (A digital version of the Operation Manual can be found on the