Résumé du contenu de la page N° 1
Canon Inkjet Photo All-In-One
series
Getting Started
Read Me First
Symbols Used in This Document
Prohibited actions.
Instructions including important information.
• In this guide, Windows 7 operating system is referred to as Windows 7
and Windows Vista operating system as Windows Vista.
• In this guide, the screens are based on Windows 7 Home Premium
and Mac OS X v.10.6.x. (Unless noted otherwise, the screens are
those of Windows 7.)
Make sure to read this manual before using the machine. Pl
Résumé du contenu de la page N° 2
■ Contents 1 Preparation ............................................................................P.4 12 Try Using the Machine...........................................................P.45 Print Photos from a Memory Card ...................................................P.46 2 Install the Print Head .............................................................P.7 Try Copying .....................................................................................P.49 Print Photos from a Co
Résumé du contenu de la page N° 3
■ Machine Installation Flow Network Connection USB Connection Using from Additional Wireless Connection Wired Connection Computers (when the machine is already connected to the network and you want to add computers from which to use the machine) Machine Preparation P.3 - 17 Machine Wireless Machine Wired Setup Setup P.18, 24 - 31 P.18, 32 - 34 Software Installation Software Installation Software Installation P.18 - 23 P.35 - 43 P.44, 35 - 43 Installation Complete Try Using the Machine P.45
Résumé du contenu de la page N° 4
This machine contains both printed manuals and on-screen manuals to be viewed on a computer. The on-screen manuals are included on the Setup CD-ROM and are installed during the software installation. Printed Manuals On-Screen Manuals •Getting Started (this manual) •Network Setup Troubleshooting Basic Guide Advanced Guide Troubleshooting Describes how to set up and use Describes basic operations Describes various operating Describes troubleshooting your machine. Introduces the and media, and g
Résumé du contenu de la page N° 5
■ Devices Required for Wireless/Wired Connection When using the machine over a wireless/wired connection, the following devices are required depending on the connection method. Wireless Connection Wired Connection Access point or Router, etc. Ethernet cable wireless router A commercial access point or router that supports A commercial network device (router, etc.) and Ethernet IEEE802.11b/g/n is required. cable are required.
Résumé du contenu de la page N° 6
1 2 1 A A Remove all orange Make sure all the following items are supplied. tape and protective Some accessories (1) are stored within the Paper Output Tray (A). Open the materials from the Paper Output Tray to remove them. • Do not install the inside and outside of machine where an 1. Print Head the machine. object may fall on it. In 2. Ink tanks (6: M, BK, GY, PGBK, C, Y) addition, do not place • The tape and 3. Manuals any object on the top protective of the machine. It may 4. Powe
Résumé du contenu de la page N° 7
3 4 5 6 E C G B D F Unlock the scanner. Insert the power cord into the Press the LCD open button (E) (1), Press the ON button (G). connector on the left side at the then adjust the LCD (Liquid Crystal 1. Open the Document Cover (B). • The machine may make some back of the machine and into the Display) (F) to a comfortable 2. Move the Scanner Lock Switch (C) operating noises. This is wall outlet firmly . viewing angle (2). towards the release mark to unlock normal operation. the Scanning Un
Résumé du contenu de la page N° 8
7 8 H I Use the { or } button (H) on the Operation Panel to select the language When the above screen is displayed, touch the OK button and go to the for the LCD, then touch the OK button. next step. • If an unintended language is displayed on the LCD, touch the Back button (I) to return to the Language selection screen. When it is necessary to turn off the machine Be sure to follow the procedure below. • When removing the power plug, make sure that the POWER lamp is not lit before removing th
Résumé du contenu de la page N° 9
1 2 2 B B A C Lift the Scanning Unit (Cover) (A) until it stops. The Print Head Holder (C) moves to the installation position. If the Print Head Holder does not move, make sure that the Close the Document Cover (B) and lift it with the Scanning Unit (Cover). machine is turned on. For details, refer to to on page 5 in “1 Preparation”. Go to the next page. Install the Print Head
Résumé du contenu de la page N° 10
3 4 5 G F D E Firmly lift the part (D) of the Print Head Lock Lever in the Print Head Remove the Print Head from the Remove the orange protective cap. Holder until it stops. silver package. The Print Head Lock Lever may feel heavy. • Handle the Print Head carefully. Do not drop or apply excessive pressure to it. • Do not touch the inside of the Print Head Holder (E). The machine may • Do not touch the inside (F) or metal parts (G) of the Print Head. The not print properly if you touch it. mac
Résumé du contenu de la page N° 11
6 7 Tilt the Print Head forward and set it in place as shown. Hold the Print Head Lock Lever firmly and lower it completely . • Do not knock the Print Head against the sides of the holder. • Once you have installed the • Install in a well-lit environment. Print Head, do not remove it unnecessarily. 2 Install the Print Head
Résumé du contenu de la page N° 12
A 1 2 3 3 B C D 1. Remove the orange tape Hold the ink tank with the orange Hold the ink tank by its sides and slowly twist the orange completely. protective cap (A) pointing up while protective cap 90 degrees horizontally to remove it off. being careful not to block the L- 2. Remove the protective film Do not push the sides of the ink tank. shape air hole (B). completely. • Do not touch the inside (C) of the orange protective cap or • Handle the ink tanks carefully. Do not drop or apply exc
Résumé du contenu de la page N° 13
4 5 6 Tilt the ink tank, then insert it under the label and Press the PUSH mark on the ink tank firmly until Install all the other ink tanks in the same way against the back end of the slot. it clicks. according to the color order indicated on the label. Make sure that the color of the label matches the ink When the installation is completed properly, the Ink tank. lamp lights red. Make sure all the Ink lamps light red. • Install in a well-lit environment. • Once you have installed the ink t
Résumé du contenu de la page N° 14
7 8 F E Close the Scanning Unit (Cover) (E). Make sure that the LCD changes as shown in the illustration and go to the next step. Make sure the Inner Cover (F) is closed. Do not touch the OK button yet. • For your safety, always close the Scanning Unit (Cover) with both hands. • It takes about 5 minutes before the LCD changes. • The machine may make some operating noises when preparing to print. This is normal operation. • If an error message is displayed on the LCD, make sure that the Print
Résumé du contenu de la page N° 15
1 2 3 4 A D C B Prepare the Paper Support (A). Move the Paper Guides (B) Load a sheet of supplied specialty paper (Matte Photo Paper to both edges. MP-101) in the Rear Tray (C). 1. Open it. Load paper in portrait orientation so that the cut corner (D) is at the 2. Withdraw it upwards. top right. 3. Tilt it back. • Be sure to use MP-101 for Print Head Alignment. Align the Print Head
Résumé du contenu de la page N° 16
4 5 6 7 8 E F Slide the left and right Make sure the Paper Output Touch the OK button. When the pattern is printed, remove the Confirm the above Paper Guides against Tray (E) is open, then open printed paper. message, then go to Print Head Alignment both edges of the the Output Tray Extension the next step. starts. Print Head Alignment is now complete. paper. (F). • Print Head • When an error message is displayed If printing starts while the Paper Alignment takes on the LCD, touch the OK
Résumé du contenu de la page N° 17
1 □ How to load specialty paper in the Rear With the machine, the paper source varies 5 Tray depending on the media type. This section describes how to load plain Specialty paper including photo paper paper in the Cassette. For details on how Load paper in the Rear Tray (A). to load specialty paper in the Rear Tray, refer to to in “4 Align the Print Head” A on page 13. C B E D Plain paper Load paper in the Cassette (B). 1. Close the Output Tray Extension Loading specialty paper • For de
Résumé du contenu de la page N° 18
2 3 4 5 G H F Pull out the Cassette (F). Move the left Paper Guide Slide the front Paper Guide Load plain paper. (G) to the edge. (H) to align with the actual Load paper with the printing side size of the paper. facing down. The front Paper Guide will click and stop when it aligns with the corresponding mark of paper size. 5 Load Paper
Résumé du contenu de la page N° 19
6 7 8 I Align the paper to the right side of Insert the Cassette slowly into the Confirm the message on the LCD, then touch the OK button. the Cassette (1), and slide the left machine until it clicks into place. The HOME screen appears. Paper Guide completely against the left edge of the paper (2). • The LCD will turn off if the machine is not operated for about 5 minutes. To restore the display, touch any button except the ON button. Make sure that the height of the paper stack does not exce
Résumé du contenu de la page N° 20
Intended Use Connection Method 6 • Want to connect to a computer with a USB cable. Go to "7 Install the USB Software (USB Connection Connection)" on page 19. • Want to connect to computers without using cables. • Want to use from multiple computers. Wireless Go to "8 Wireless Setup" on page 24. Connection • Want to use from multiple computers. • Want to connect to a computer with an Ethernet cable. Wired Go to "9 Wired Setup" on page 32. Connection If it is uncertain whether your device
