ページ1に含まれる内容の要旨
N8849
Please keep this instruction sheet for future reference,
as it contains important information.
Requires four “D” (LR20) alkaline batteries for mobile
operation and two "AAA" (LR03) alkaline batteries for
remote operation (batteries not included).
Adult assembly is required.
Tool required for assembly: Phillips screwdriver (not included).
www.fisher-price.com
1
ページ2に含まれる内容の要旨
Consumer Information WARNING Prevent Entanglement Injury • Keep out of baby’s reach. • Remove mobile portion of product from crib or playpen when baby begins to push up on hands and knees. • This product may not attach to all crib designs. Do not add additional strings or straps to attach to crib or playpen. • The mobile portion of this product may be used from birth until 5 months. • The base portion of this product may be used from birth until 36 months. • A crib mobile is intended
ページ3に含まれる内容の要旨
Parts Canopy Arm 4 Soft Toys Crib Adaptor Remote Base Retainer (2 Pieces) Note: All of the screws used to assemble this toy are attached to the product. Follow these instructions carefully to fully secure the screws. Tighten and loosen all screws with a Phillips screwdriver. Do not over-tighten the screws. 3
ページ4に含まれる内容の要旨
Battery Installation 1.5V x 4 “D” (LR20) We recommend using alkaline batteries for longer battery life. Mobile Base • Loosen the screws in the batter y compartment door with a Phillips screwdriver. Remove the battery compartment door. • Insert four “D” (LR20) alkaline batteries. • Replace the battery compartment door and tighten the screws. IMPORTANT! Under normal use conditions, the batteries in the mobile base will require replacement more often than the batteries in the remote. When sou
ページ5に含まれる内容の要旨
Assembly Base Crib Adaptor 1 1 • Fit the crib adaptor to the base and tighten the screws. IMPORTANT! Make sure the straps are over the top of the crib adaptor. Canopy Arm 2 1 • First, fit the top retainer piece onto the end of the arm. • Next, fit the canopy onto top retainer piece. • Then, fit the bottom retainer piece onto the canopy and tighten the screw. 5
ページ6に含まれる内容の要旨
Assembly PRESS A SLIDE SLIDE B Arm Socket Base 3 1 A • First, press the button on the mobile base, next to the socket and then slide the socket door open B . • Fit the arm into the socket in the base and tighten the screws. Soft Toy 4 1 • Fit the string on a soft toy through the slot in the canopy . Pull down gently on the soft toy to secure the string in the large leaf spoke. • Repeat this procedure to attach the remaining soft toys to the canopy. Fisher Price, Inc., a subsidiary of Mat
ページ7に含まれる内容の要旨
Crib Attachment Crib Top Rail Base B Buckles uckles 1 1 • Position the base so that the decorated side faces the inside of the crib. • Fit the base onto the crib top rail. • Make sure the top strap is hanging over the crib top rail. Pull the bottom strap through the crib rails. • Buckle the straps. Make sure you hear a “click”. 2 1 • Make sure the straps are tightened securely around the crib rail. • While pushing the tab at the bottom of the buckle, pull the free end of the strap to tighten
ページ8に含まれる内容の要旨
Crib Attachment 3 1 • Tie the base strings to a crib spindle. Note: It is better the tie the strings in a knot than a bow, since a bow may be easily untied. B Bottom of Base ottom of Base A At Least 7 Inches t Least 7 Inches Mattress Mattress 4 1 • If the distance between the base and the mattress is less than 7 inches, lower the crib mattress. 8
ページ9に含まれる内容の要旨
Use IMPORTANT! • In the unlikely event that use of the remote interferes with normal use of other remote controlled equipment, such as televisions, stereos, or use of other electronic or battery powered appliances interfere with operation of the mobile, do not use both appliances at the same time. • For best per formance between the mobile and the remote, avoid using the remote in areas of bright light. In bright natural or artificial light, you may notice loss of range. Move the mobile or
ページ10に含まれる内容の要旨
Use Projector/Sound Switch Projector/Sound Switch Slide the switch to: - turns on sounds, mobile and projector - turns on sounds and mobile - turns on sounds only P Power/V ower/Volume Switch olume Switch • Slide the switch to on with low volume or on with high volume . When finished using the product, slide the switch off . M Music or Sound Select Buttons usic or Sound Select Buttons Press a music or sound button on the front of the mobile base: - for Bach, Beethoven an
ページ11に含まれる内容の要旨
Convert to Music Box Remove the mobile and use as a music box with a projection show! • Loosen both screws in the arm near the mobile base. Lift and remove the arm. • Close the socket door on top of the mobile base. IMPORTANT! The socket door must be closed for sound and projection operation. If sounds or lights are not working, make sure the door is completely closed. • Store the mobile in a safe place for future use. 11
ページ12に含まれる内容の要旨
Consumer Information FCC Statement (United States Only) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio com
