ページ1に含まれる内容の要旨
COLOUR VIDEO CAMERA
INSTRUCTIONS
TK-C1480
TK-C1481
For Customer Use:
Enter below the Serial No. which is
located on the body. Retain this
information for future reference.
Model No. TK-C1480, TK-C1481
Serial No.
SC961006H-007
E-1
DIGITAL
COLOR VIDEO CAMERA
BF LOOK
∞
ページ2に含まれる内容の要旨
IMPORTANT SAFEGUARDS 1. Read all of these instructions. 2. Save these instructions for later use. 3. All warnings on the product and in the operating instructions should be adhered to. 4. Unplug this appliance system from the wall outlet before cleaning. Do not use liquid clean- ers or aerosol cleaners. Use a damp cloth for cleaning. 5. Do not use attachments not recommended by the appliance manufacturer as they may cause hazards. 6. Do not use this appliance near water - for example, near a bat
ページ3に含まれる内容の要旨
13. Follow all warnings and instructions marked on the appliance. 14. Do not overload wall outlets and extension cords as this can result in fire or electric shock. 15. Never push objects of any kind into this appliance through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the appliance. 16.Do not attempt to service this appliance yourself as opening or removing covers may expose you to
ページ4に含まれる内容の要旨
Safety Precautions Due to design modifications, data given in this FOR USA AND CANADA instruction book are subject to possible change without prior notice. CAUTION RISK OF ELECTRIC SHOCK WARNING: DO NOT OPEN TO REDUCE THE RISK OF FIRE OR CAUTION:TO REDUCE THE RISK OF ELECTRIC ELECTRIC SHOCK, DO NOT SHOCK. DO NOT REMOVE COVER (OR EXPOSE THIS APPLIANCE TO RAIN BACK). NO USER-SERVICEABLE PARTS INSIDE.REFER SERVICING TO OR MOISTURE. QUALIFIED SERVICE PERSONNEL. AVERTISSEMENT: The lightning flash wis
ページ5に含まれる内容の要旨
Thank you for purchasing this product. (These instrustions are for TK-C1480U, TK-C1480E and TK-C1481EG) Before beginning to operate this unit, please read the instruction manual carefully in order to make sure that the best possible performance is obtained. CONTENTS INTRODUCTION Features ...............................................................................................................................6 Operating Precautions ............................................................
ページ6に含まれる内容の要旨
INTRODUCTION Features A new DSP (Digital Signal Processor) Before starting an important recording, features a Extended Dynamic Range be sure to perform a test recording in (ExDR) and enables to shoot both bright order to confirm that a normal and dark locations. recording is possible. We do not accept liability for the loss of The use of a new CCD with a SENSE UP a recording in the case of it becoming (X32) function realized the minimum impossible to record due to a problem luminous flux
ページ7に含まれる内容の要旨
Operating Precautions ● To save energy, when it is not being used ● Observe the following when carrying out turn the system’s power off. camera maintenance. ● This camera has been designed for indoor • Turn the power OFF before proceeding use. When you use it outdoor, be sure to to carry out maintenance. use a housing and the like. If it is contaminated seriously, clean the ● Do not install or use the camera in the contaminated part with a cloth (or a following places. tissue) which has been soa
ページ8に含まれる内容の要旨
INTRODUCTION Controls, Connectors and Indicators 2 1 3 4 5 7 6 Lens mount Camera-mounting bracket 1 4 This means to attach the lens. The bracket has been attached on the This is applicable to both the C-mount bottom of the camera before shipment. It lenses and CS-mount lenses. can also be attached on the top according to the circumstance. Backfocus adjustment ring 2 To re-attach the bracket use the threaded Adjusting the back focus during lens holes at the top, with the camera installation. moun
ページ9に含まれる内容の要旨
! @ #$ SET % CAMERA SETUP AWC EXT TERM-OFF ON ^ MENU LL INT/GL DUPLEX SIMPLEX & ON RX TERM-OFF * NOT USED IRIS VIDEO DC 8 90 Cover screen is brought up. 8 The cover opens if it is pulled to the left ( Page 23) while being pushed. [SET/AWC] Set. Auto White Control 12 Button [VIDEO/DC] Iris Selector Switch 9 SET: Press this button to display a sub- This is set according to the type of lens menu. when an automatic iris control lens is ( Page 23) used. AWC: If this button is kept pressed for VID
ページ10に含まれる内容の要旨
INTRODUCTION Controls, Connectors and Indicators (Continued) [ , , , ] Up-and-down, left-and- SIMPLEX: 13 right Button This switch sets to SIMPLEX when the These buttons select items on the menu transmission between the camera and a screen and change a set value. remote control unit is in a simplex system ( Page 23) (one-way). (DUPLEX: At time of factory shipment) [EXT.TERM-ON/OFF] Terminal On/Off 14 Switch of External Synchronization [RX.TERM-ON/OFF] RX Signal Terminal 17 Signal ON/OFF Switch
ページ11に含まれる内容の要旨
( ) ⁄ fl + - 12 TX+ TX- RX+ RX- AUX GND GND TX+ TX- RX+ RX- AUX A B CD A B CD Y/C OUT Y/C OUT fi ¤ SYNC IN VIDEO OUT SYNC IN VIDEO OUT SEE INST- SEE INST- RUCTION RUCTION POWER MANUAL › MANUAL POWER ‹ TK-C1480U and TK-C1480E TK-C1481EG [DC 12V, AC 24V] Power input terminals [VIDEO OUT] Video signal output 19 23 (TK-C1480U and TK-C1480E) connector To input DC 12V or AC 24V power. This BNC connector outputs a composite [TX+A, TX-B, RX+C, RX-D] Control video signal. Connect this to the video input 20
ページ12に含まれる内容の要旨
CONNECTION/INSTALLATION RM-P2580 System System with up to 8 cameras Camera TK-C1480 Control signal cable Video signal cable Camera 1 AC24V MACHINE ID:1 Power or (Menu screen) cable DC12V RX TERM: OFF Camera (switch) TK-C1480 Camera 2 AC24V MACHINE ID:2 or (Menu screen) DC12V RX TERM: OFF (switch) Camera TK-C1480 MONITOR Camera 8 AC24V •• • • • Time lapse VCR CAM SW MACHINE ID:8 or SR-L910 OUT REC STOP/EJECT CHECK REC VIDEO CASSETTE RECORDER OPERATE (Menu screen) OPE. LOCK REVERSE PAUSE/ STILL
ページ13に含まれる内容の要旨
Connecting the control signal cable (Use a twisted-pair cable for connection. Page 17.) Camera 1 control signal connection terminals RM-P2580 Connect: A RX + TX+ A Camera TX+ to RM-P2580 RX+ B RX TX B Camera TX– to RM-P2580 RX– RX+ C C TX + Camera RX+ to RM-P2580 TX+ RX D D TX Camera RX– to RM-P2580 TX– Camera 2 The A B C D marks indicated on both the control signal camera terminals and the RM-P2580 termi- connection terminals nals facilitate correct connections. Connect TX+ A the te
ページ14に含まれる内容の要旨
Av Pk L H ALC LEVEL CONNECTION/INSTALLATION Procedures Execute connection/installation according to the procedures described below. Turn OFF the power supply to all equipment to be used before making carefully. 4.Setting the switches 6.Back focus adjustment ( Page 13) ( Page 21) SET CAMERA SETUP EXT TERM-OFF ON MENU INT/GL LL DUPLEX SIMPLEX ON RX TERM-OFF IOT USED VIDEO DC 7.Auto white balance 5.Lens adjustment control adjustment ( Page 20) ( Page 22) 1.Mounting the lens 3.Mounting
ページ15に含まれる内容の要旨
Mounting the lens Mount the lens according to the procedures described below. 1. Before mounting a lens, check whether it is a C-mount or CS-mount lens. To change the mounting method, loosen the back-focus locking screw (M 2.6) using a Phillips head screwdriver, turn the back-focus adjusting ring with your fingers or the screwdriver and change the mounting method. Dimension (b) of the lens shown in the illustration must be as shown in the table below. If (b) exceeds the value in the (b) F table,
ページ16に含まれる内容の要旨
CONNECTION/INSTALLATION Connections on the back Connect the DC 12 V or the AC 24 V power Power supply supply to the DC 12V/AC 24V terminals. To TK-C1480U and TK-C1480E (DC 12 V or 24 V) prevent connection errors or a cable disconnection, we recommend the use of lug plates for the connections. The following table shows the connection distances and connection cables provided + - 1 2 that 2-conductor VVF cables (vinyl-insulated vinyl sheath cables) are used. TX+ TX- RX+ RX- AUX GND A B CD Maximum
ページ17に含まれる内容の要旨
Control signal cables Genlock connection These cables should be connected only when With some systems, when the external sync it is required to control the camera using the signal is a composite video or black burst sig- RS-442A or RS-485 signals. The use of 0.65 nal genlocking by applying an external sync 4-conductor twisted pair cables is recom- input requires the horizontal phase (H mended. With these cables, the maximum ex- PHASE) and colour phase (SC COARSE) to tension distance is 1,200
ページ18に含まれる内容の要旨
CONNECTION/INSTALLATION Mounting the camera When mounting the camera on a fixer, pan/ tilt, etc., use the camera mounting screw hole Camera mounting located on the camera-mounting bracket. screw Camera-mounting bracket CAUTION: Use the screw with a length shorter than 7mm from a camera-mounting face. MAX. 7mm Furthermore, make use of the rotation Rotation prevention hole prevention hole to prevent the camera from falling and securely mount the camera. Special precautions must be taken for mounti
ページ19に含まれる内容の要旨
Installation of camera q • Mounting from the bottom This camera is originally designed to be mounted from the bottom, as shown q. IRIS The hole is standard photographic pan- VIDEO DC head screw size (1/4-20 UNC). Example the Fixing unit or Pan/Tilt unit. • Mounting from the top Remove the CAMERA MOUNTING BRACKET from the bottom of the camera by removing two fixing screws as shown w. Attach the CAMERA MOUNTING BRACKET to the top, then mount the camera on the Fixing Unit as shown e. Make sure that
ページ20に含まれる内容の要旨
CONNECTION/INSTALLATION Lens adjustment Connect the camera according to the connection method, turn it on, display an image on the monitor, and check the image. The camera has been factory-adjusted to the best position, but it may need to be adjusted according to the object conditions or combination of lenses. If the image is unnatural, adjust it as follows: (Also read the instruction manual of the lens.) LEVEL adjustment • LEVEL adjustment Monitor screen LEVEL turning direction Too bright Count
