ページ1に含まれる内容の要旨
Digital Trail Camera
Instruction Manual
Model#: 119203C LIT #: 98-1164/03-10
ページ2に含まれる内容の要旨
® Congratulations on your purchase of the Tasco Digital Trail Camera! This weatherproof, rugged trail camera is designed to record still images or movie clips of outdoor wildlife activity. This instruction manual will help you understand, setup, and use your Cam to achieve the best possible results. Tasco Digital Trail Cam Features If you’ve been looking for a digital game scouting or surveillance camera that has all the essential features but without the unwanted frills, expense, or
ページ3に含まれる内容の要旨
QUICK GUIDE: TASCO TRAIL CAMERA 1. Open the camera by releasing the latches on the right side of the camera. Install 4 “D” cell batteries (flat base of all batteries contacting springs), and insert an SD card (not included, use any capacity up to 2GB) in the slot to the right of the 5 buttons (upside down, brand name facing you). Press the card down until you hear it click into place. 2. Press and release the Power switch. If you are using the camera for the first time, you should se
ページ4に含まれる内容の要旨
Digital Trail Cam Specifications Lens F/3.5, effective focal length 42mm. Sight range: 45 degrees Flash High power electronic Xenon Flash. Range: 30 ft. PIR Sensor Low noise, high sensitivity passive infrared sensor. Range: 30 ft. Motion LED Indicator Yes Display Monochrome LCD. Auto-off: 3 min. 2-digit event and image display. File Format Standard JPEG format (.jpg) still photos. Video movie clips (.avi). DCF ver. 1.0 file management. Photo Modes 1.3MP or 3MP* still photo, or AVI video (3
ページ5に含まれる内容の要旨
Glossary PIR—Passive Infrared Sensor. Senses motion like typical security motion detector. Requires infrared energy (heat) in addition to motion to trip sensor to assure detection of live animals. Image—A digital picture recorded on the SD Card when motion is sensed. Images are taken at the desired delay between images. Image Delay—Time elapsed between photos while events are sensed and recorded. This is fixed at 30 second intervals in the Trail Cam. Camera Flash—Xenon Flash used for low
ページ6に含まれる内容の要旨
Front of Camera Control Panel PIR Inside Front Flash LCD Camera Display SD Card Slot Lens Button & Display Detail Setup, PIR Detected (or Menu & Low Battery) LED Power Buttons Lock Tab Parts Guide 6
ページ7に含まれる内容の要旨
Setup and Operation Guide 1. Open the Cam by pulling out on the two latches on the right side. Install 4 “D” cell batteries (flat base of all batteries contacting springs), and insert an SD card (not included, use any capacity from 16MB to 8GB. Do not substitute MMC cards.) in the slot to the right of the 5 buttons as indicated on the slot cover (upside down, with the notched corner of the card on the left and metal contacts of the card facing the back of the slot). Press the card down until
ページ8に含まれる内容の要旨
Setup Guide (cont.) resolution images of better quality but fewer images can be stored to the card. In Movie mode a 14 second AVI file will be recorded to the SD Card each time the camera is triggered. 4. Pressing ENTER again after the resolution options will go to the Format screen next. Formatting is recommended before you re-use an old SD card, and is a quick way to erase all of the photos/videos after you’ve saved any you wish to keep. The display will read “FoNo”, with “No” and the SD c
ページ9に含まれる内容の要旨
Setup Guide (cont.) by “SnAP”, then “SLP” (Sleep). Note: for movie clips, the display will stay on “SnAP” for the 14 sec duration of each movie. 7. Thread the strap through the slots on the back of the Cam and attach the buckles, then strap it onto a suitable tree, making sure the strap is tight and the camera is aimed at the area you wish to observe. The red LED lamp on the front of the camera can help you determine how large an area is covered, as it will flash when an “event” is detect
ページ10に含まれる内容の要旨
Additional Notes MOON PHASE STAMP All new Trail Cam models have a “moon phase” stamp feature. This links the current date (as set by the user in the setup procedure) to the phase of the moon on that date (this data is stored on an internal memory chip), and imprints a icon on your photo which represents the moon phase when the photo was taken. The moon phase icon will appear on your photos in the lower left, next to the Tasco logo. Some hunters will find this to be a useful reference, as it
ページ11に含まれる内容の要旨
FCC Note: ONE YEAR LIMITED WARRANTY This equipment has been tested and found to comply with the limits for a Class B digital device, Congratulations on the purchase of your new Tasco product. You have chosen one pursuant to Part 15 of the FCC Rules. These limits are of the finest values available today. This product carries Tasco’s ONE YEAR LIMITED designed to provide reasonable protection against WARRANTY. This product is warranted against original defects in material and/or harmful inte
ページ12に含まれる内容の要旨
For further questions or additional information please contact: Tasco 9200 Cody, Overland Park, Kansas 66214 (800) 423-3537 • www.tasco.com ©2010 B.O.P.
