ページ1に含まれる内容の要旨
INSTALLATION INSTRUCTIONS
Instrucciones de instalación Istruzioni di installazione
Installationsanleitung Installatie-instructies
Instruções de Instalação Instructions d´installation
Automated Dual Horizontal Door System
This device complies with part 15 of the FCC rules. Operation is subject to the following 2 conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This
ページ2に含まれる内容の要旨
CM6DH SERIES Installation Instructions CSAV, Inc., and its affiliated corporations and subsidiaries (collectively, "CSAV"), intend to make this manual accurate and complete. However, CSAV makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any ki
ページ3に含まれる内容の要旨
CM6DH SERIES Installation Instructions TOOLS REQUIRED FOR INSTALLATION 1/2" (12.7mm) #2 PARTS A (1) B (1) G (1) C (2) F (2) D (1) 08 x 1/2" E (1) 3
ページ4に含まれる内容の要旨
CM6DH SERIES Installation Instructions Installing to Cabinet INSTALLATION 1. Place mechanism (A) on top of cabinet. (See Figure 1) Cabinet Considerations 2. Align center of track with center of the door opening. 1. Header must not extend beyond top of track. 3. Attach using #8 or #10 screws through the holes in track. 2. Guide wheel must have free play in toe space. 4. Attach motor box to the track following instructions in box. 3. Doors must not exceed 50 lbs (each). (See Figure 2) 4. Allow amp
ページ5に含まれる内容の要旨
Installation Instructions CM6DH SERIES Figure 1 5
ページ6に含まれる内容の要旨
CM6DH SERIES Installation Instructions Figure 2 6
ページ7に含まれる内容の要旨
Installation Instructions CM6DH SERIES Hanging and Adjusting Doors 1. Remove door hanger from mechanism by removing locking screws and washers. (See Figure 3) Locking Screws and Washers Door (F) x 2 Hanger Figure 5 Figure 3 4. Move carriages to one half open position by activating mechanism and pressing button a second time when 2. Center door hanger to top of door and secure with eight flat carriage reaches desired position. (See Mechanism head screws of sufficient length to support weight of d
ページ8に含まれる内容の要旨
CM6DH SERIES Installation Instructions 8 From Dimmer Module 7 Figure 7 IR Sensor Placement Figure 8 The placement of the IR sensor can be crucial to proper System Activation operation of the system. A flexible IR sensor is provided to make it easier to achieve reliable operation. 1. Insert plug from the power supply into the jack on the top of the motor box. In most applications, the IR sensor may be installed on top of the cabinet. However, tall and/or dark colored ceilings can absorb the IR si
ページ9に含まれる内容の要旨
Installation Instructions CM6DH SERIES Activator Activator Button Figure 10 Figure 12 5. Press the "Open Door" button on the Remote Control. The controller will then be in “Learn Mode” (The door will move for 3 seconds, stop for 10 seconds, and when it starts moving NOTE: If a different travel distance is required see "Door Travel again it will be in it’s “Learn Mode”). Adjustment below. When put into “Learn Mode” the mechanism runs back and ADJUSTMENTS forth several times and measures it’s envi
ページ10に含まれる内容の要旨
CM6DH SERIES Installation Instructions track, or is the motor box bent, causing it to become uncoupled Control Input on Front of Motor Box from the track? Power Loss - The Status Light will be on solid red. ---- There Control Input has been a power loss (due to an electrical storm, etc.). When next activated the doors will move at a slow speed to their full closed position. If the doors are already closed they will not move. The Status Light will return to solid green and the doors are ready
ページ11に含まれる内容の要旨
Installation Instructions CM6DH SERIES 11
ページ12に含まれる内容の要旨
CM6DH SERIES Installation Instructions USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378 P 800.582.6480 / 952.894.6280 F 877.894.6918 / 952.894.6918 Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands P +31 (0)40 2668620 F +31 (0)40 2668615 Asia Pacific A Room 24F, Block D, Lily YinDu International Building LuoGang, BuJi Town, Shenzhen, CHINA. 8820-000022 RevA 2007 Chief Manufacturing D 24F D 24F www.chiefmfg.com P +86-755-8996 9226 11/07 F +86-755-8996 9217
