ページ1に含まれる内容の要旨
Installation Instructions
for Stacked Washers and Dryers
Inside......................................
Dimensions........................................................................ 3
Before You Start................................................................ 4
Installation......................................................................... 5
Installer Checklist ............................................ Back Cover
Date Purchased _____________________________
Model Number ________
ページ2に含まれる内容の要旨
WARNING FOR YOUR SAFETY, the information in this manual must be followed to minimize the risk of fire or explosion or to prevent property damage, personal injury or death. W033 • Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. • WHAT TO DO IF YOU SMELL GAS: – Do not try to light any appliance. – Do not touch any electrical switch; do not use any phone in your building. – Clear the room, building or area of all occupants. – Imme
ページ3に含まれる内容の要旨
Dimensions 23.5 in. (59.7 cm) 8.0 in. (20.3 cm) 15.4 in. (39.1 cm) 5.25 in. (13.3 cm) 24 in. (61 cm) *13.1 in. (33.3 cm) 28 in. 26.875 in. *14.6 in. (71.1 cm) (68.3 cm) (37.08 cm) 2.0 in. 1.5 in. (5.1 cm) (3.81 cm) ELECTRIC DRYERS SWD897N * With leveling legs turned into base. NOTE: Exhaust openings are 4 inch (10.2 cm) metal ducting. 23.5 in. (59.7 cm) 8.0 in. (20.3 cm) 15.4 in. (39.1 cm) 5.25 in. (13.3 cm) 1 24 in. 2.3 in. (61 cm) (6 cm) *13.1 in. (33.3 cm) 28 in. 26.875 in. *14.6 in. (71.1
ページ4に含まれる内容の要旨
" 6 1 / 9 Before You Start WARNING Supplies Any disassembly requiring the use of For most installations, the basic supplies you will need tools must be performed by a suitably are: qualified service person. W299 3 1 2 NOTE: If the unit is delivered on a cold day (below freezing), or is stored in an unheated room or area during the cold months, do not attempt to operate it until the unit has had a chance to warm up. 5 6 NOTE: Some moisture in the wash drum is normal. Water is used during t
ページ5に含まれる内容の要旨
NOTE: For best performance and to minimize Installation vibration or movement, install washer on a solid, Step 1: Position Unit Near Installation sturdy and level floor. Some floors may need to be reinforced, especially on a second floor or over a Area basement. Do not install the washer on carpeting, Move unit as close to the desired area of installation as soft tile, a platform or other weakly supported possible. structures. Step 2: Position and Level the Unit WARNING Position unit so i
ページ6に含まれる内容の要旨
NOTE: Use of the dispenser drawer or unit doors as a handle in the transportation of the unit may cause damage to the dispenser or doors. Place unit in position on a solid, sturdy and level floor. Installing the unit on any type of carpeting, soft tile, a platform or other weakly supported structures is not recommended. Place a level on the cabinet top and check if the unit is level from side to side and front to back. NOTE: Level must rest on raised portion of top panel. Refer to Figure
ページ7に含まれる内容の要旨
Step 3: Connect Fill Hoses NOTE: When installing in newly constructed or renovated buildings, it is very important to flush the lines since build-up may have occurred during WARNING construction. Under certain conditions, hydrogen gas Connecting Hoses may be produced in a hot water system Remove the two plain rubber washers and two filter that has not been used for two weeks or screens from the accessories bag. Install them into more. HYDROGEN GAS IS EXPLOSIVE. If each end of the fill h
ページ8に含まれる内容の要旨
IMPORTANT: Hoses and other natural rubber Risers parts deteriorate after extended use. Hoses may Risers (or air cushions) may have to be installed if the develop cracks, blisters or material wear from the pipes knock or pound when flow of water stops. The temperature and constant high pressure they are risers are more efficient when installed as close as subject to. possible to the water supply faucets (refer to Figure 7). All hoses should be checked on a monthly basis for any visible sig
ページ9に含まれる内容の要旨
Step 4: Connect Drain Hose to Drain NOTE: End of drain hose must not be below 24 in. (61 cm). Receptacle Remove the drain hose from its shipping position on the rear of the washer by unhooking the hose from the retainer clamp and by removing the shipping tape. Install the drain hose into the drain receptacle (standpipe, wall or laundry tub) following the 1 instructions below. 2 IMPORTANT: Drain receptacle must be capable of handling a minimum of 1-1/4 inch (32 cm) outside diameter drain h
ページ10に含まれる内容の要旨
Step 5: (Gas Dryer Only) Connect Gas Natural Gas Altitude Adjustments Supply Pipe Altitude Orifice Size Part No. feet m No. inches mm WARNING 3000 915 43 0.0890 2.26 503778 To reduce the risk of gas leaks, fire or 6000 1830 44 0.0860 2.18 58719 explosion: 8000 2440 45 0.0820 2.08 503779 • The dryer must be connected to the type of gas as shown on nameplate located in 9000 2740 46 0.0810 2.06 503780 the door recess. 10,000 3050 47 0.0785 1.99 503781 • Use a new flexible stainless steel Table
ページ11に含まれる内容の要旨
4. Tighten all connections securely. Turn on gas and check all pipe connections (internal & external) WARNING for gas leaks with a non-corrosive leak detection fluid. To reduce the risk of fire, electric shock, serious injury or death, all wiring and NOTE: The dryer and its appliance main gas valve grounding MUST conform with the latest must be disconnected from the gas supply piping edition of the National Electrical Code, system during any pressure testing of that system ANSI/NFPA 7
ページ12に含まれる内容の要旨
Grounding Information NOTE: Branch circuit wire size requirements to laundry room outlet are shown in Table 3 and • This dryer must be connected to a grounded Table 4. metal, permanent wiring system; or an equipment-grounding conductor must be run Model LTSA7A*N2989 with the circuit conductors and connected to the equipment-grounding terminal or lead on the Wire Length Wire dryer. Less than Listed No. 8 AWG • For model LTSA7A*N2989, only flexible metal 15 ft. (4.5 m) Copper wire only co
ページ13に含まれる内容の要旨
Connecting Power Cord with Three-Wire Plug NOTE: Four-wire cord is required for mobile homes or where codes do not permit grounding through neutral. NOTE: The power cord is NOT supplied with the electric dryer. Type of power cord and gauge of wire must conform to local codes and instructions. POWER SUPPLY POWER SUPPLY 1 The method of wiring the dryer is optional and subject to local code requirements. 2 NOTE: Connect the dryer to the power supply with the MAXIMUM RATED VOLTAGE listed on t
ページ14に含まれる内容の要旨
120 ± 12 V.A.C. 120 ± 12 V.A.C. 4. Use the three screws from the accessories bag to Connecting Power Cord with Four-Wire Plug attach the power cord wires to the terminal block. NOTE: Four-wire cord is required for mobile Refer to Figure 15. homes or where codes do not permit grounding through neutral. 1 2 2 1 3 3 4 D286I 1 “L1” Terminal 240 ± 12 0 V.A.C. 2 Neutral Terminal V.A.C. 3 “L2” Terminal Figure 15 5. Tighten all screws firmly. DRY2016N IMPORTANT: Failure to tighten these screws 1 Typ
ページ15に含まれる内容の要旨
3. Remove ground screw and save for use in Step 5. 5. Attach power cord ground (green) wire to rear Remove wire and use in Step 6. bulkhead using ground screw removed in Step 3. 1 1 7 6 5 2 4 D697I D697I DRY1920N 1 Ground Screw 3 DRY1920N Figure 18 1 White 2 “L2” Terminal 4. Use a strain relief and insert end of power cord 3 Black through power supply hole. 4 Green 5 Red 6 Neutral Terminal 7 “L1” Terminal Figure 20 6. Use the three screws from the accessories bag to attach the remaining pow
ページ16に含まれる内容の要旨
Step 7: Connect Dryer Exhaust System • Locate dryer so exhaust duct is as short as possible. • Be certain old ducts are cleaned before installing WARNING your new dryer. • Use 4 inch (102 mm) diameter rigid or flexible To reduce the risk of fire and combustion metal duct. gas accumulation the dryer MUST be • The male end of each section of duct must point exhausted to the outdoors. away from the dryer. W604 • Use as few elbows as possible. To reduce the risk of fire and the accumulation o
ページ17に含まれる内容の要旨
Exhaust Direction Exhaust System The dryer can be exhausted to the outdoors through the For best drying results, recommended maximum back, left, right or bottom of the dryer. EXCEPTION: length of exhaust system is shown in Table 5. Gas dryers cannot be vented out the left side To prevent backdraft when dryer is not in operation, because of the burner housing. outer end of exhaust pipe must have a weather hood Dryer is shipped from factory ready for rear exhaust. with hinged dampers (obtain l
ページ18に含まれる内容の要旨
Step 8: (Washer Only) Remove the Shock IMPORTANT: DO NOT tip washer more than 6 inches (152.4 mm) in any direction after shipping Sleeves and Shipping Brace brace has been removed. Shock absorbers may Remove front access panel by removing the two separate and damage to unit may result. For screws at the bottom of the panel. leveling purposes, the unit may be tilted a maximum of 6 inches (152.4 mm) in any direction. Remove the five bolts and lockwashers from shipping brace with 9/16 inch w
ページ19に含まれる内容の要旨
Step 10: Plug In the Washer and Dryer The dryer is designed to be operated on a separate branch, polarized, three-wire, effectively grounded, Electric Dryer 120 Volt, 60 Hertz, AC (alternating current) circuit protected by a 15 Ampere fuse, equivalent fusetron or Connect the dryer to an electrical power source. Refer circuit breaker. to Step 4 for information on connecting power cord. The three-prong grounding plug on the power cord should be plugged directly into a polarized three-slot e
ページ20に含まれる内容の要旨
Washer - All Models Except LTSA7A*N2989 WARNING Washer requires 120 Volt, 60 Hertz electrical supply and comes equipped with a 3-prong grounding plug. To reduce the risk of an electric shock or Refer to serial plate for specific electrical fire, DO NOT use an extension cord or an requirements. adapter to connect the dryer to the electrical power source. NOTE: The wiring diagram is located behind the W037 control panel, inside the control cabinet. 2 3 1 2 1 3 120±12 0 V.A.C. V.A.C. 120±12
