ページ1に含まれる内容の要旨
SYMPHONY
serIes
Owner’s Manual &
InstallatIOn GuIde
Note: Read all instructions before proceeding with installation.
All specifications are ± 1/4’’ and are subject to change without notice.
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
t able oF contents Product registration inForMation 4 congratulations! 5 saFety instructions 6 installation instructions Pre-Installation Procedures 7 Electrical Installation 8 Structural Preparation 9 Framing Diagrams 10 Integrally Skirted Whirlpools 11 Flat Panel Skirt Installation 12-14 System Test and Clean-Up 15 oPeration Whirlpool Operations 16-18 Maintenance and care Initial Cleaning 19 Whirlpool System Cleaning 19 S
ページ4に含まれる内容の要旨
aquatic industries, inc. Product registration information Your product warranty is registered and confirmed with Aquatic through the Serial Number on your unit. You do not need to contact Aquatic to confirm registration. Please fill out the information below and reference when contacting the distributor to expedite warranty claims. oWner inForMation: Model name serial number (See Table of Contents for Location) Purchase date distributor P.O. Box 889 • Leander, TX 78646-0889 Phone (800) 92
ページ5に含まれる内容の要旨
CONgRATULATIONS! You have chosen one of the finest bath products in the world! Aquatic Industries supports your purchase with strong commitments to quality and customer satisfaction. Please read and follow all of the instructions contained in this Owner’s Manual before installing, operating or maintaining your whirlpool. In addition, you should continually refer to these instructions during the life of your whirlpool. Failure to comply with these instructions may invalidate your warranty
ページ6に含まれる内容の要旨
iMPortant saFety instructions Warning: When using this unit, these basic Precautions should be FolloWed. This manual contains information and instructions for proper operation and maintenance of your whirlpool. Failure to follow these instructions could result in personal injury, electrical shock or fire. read and FolloW all instructions danger! to reduce the risK oF injury: 1. Do not permit children to use this unit unless they are closely supervised by an adult at all times. Supervisio
ページ7に含まれる内容の要旨
installation instructions / guidelines read all instructions careFully beFore installation Pre-installation Procedures: 1. This whirlpool is factory-assembled, complete with motor, pump, controls and plumbing. do not lift or support unit using plumbing lines or any part of circulation system. do not relocate or otherwise modify any part of the factory-installed circulation system, as this may affect the performance or safe operation of the whirlpool and will void all warranties. 2. Insp
ページ8に含まれる内容の要旨
installation instructions electrical installation: all local, state and national electrical codes must be observed by a licensed electrician in connecting power to the aquatic whirlpool. When using electrical products, basic precautions should always be observed, including the following: 1. read and FolloW all instructions. 2. circuit: A separate circuit (not to supply any other electrical devices) is required as follows: For units equipped with a pump motor only, a 110/120 vAC 15 Amp circuit
ページ9に含まれる内容の要旨
installation instructions structural PreP aration: Framing and supports will vary according to the model and type of installation selected. 1. Plumbing connections: (spout, handles, valves, etc.) should be made after unit is installed. When mounting fittings on unit, drill holes from finished surface, using appropriate-sized hole saw with fine-tooth or abrasive grit cutting edge. 2. When plumbing connections have been made, proceed with electrical hook-up (see Electrical Installation on pa
ページ10に含まれる内容の要旨
installation instructions alcoVes islands rectangular Models ↔ corner Models ↔ A oval Models ↔ Measurements should be taken directly from the tub. decK cutout : A paper template will be enclosed with all oval models. For the deck cutout, scribe on the deck two center lines (a major and minor axis). Next, match the center lines and trace the ellipse. Repeat this step three more times. Once the tracing is complete, cut out the ellipse. The dimensions should be exactly 2” smaller than
ページ11に含まれる内容の要旨
installation instructions integrally sKirted WhirlPools: remove the shipping blocks of wood that are nailed along the back of the long 1 x 4 of the “h” frame. 1. To avoid obstructions during installation, make sure water lines, spout pipes and valve plumbing do not project into alcove. 2. ledger strip: Fasten a 1” x 3” (25mm x 75mm) ledger strip along rear for alcove and along both sides in corner installations at Dimension LH. (see diagram 6A) 3. Mix a 3 gallon bucket of cement mortar and
ページ12に含まれる内容の要旨
Flat Panel sKirt installation instructions Please read instructions beFore Proceeding With installation note: the skirt panel may require re-sizing to fit the specific installation. Carefully take your measurements so that the skirt will fit the skirt opening. If re-sizing is required, it is suggested that the skirt is measured and marked to the required dimensions. Cut to within 1/8” of finished dimensions using a fine tooth saw. Use a belt sander to remove the remaining material to the fin
ページ13に含まれる内容の要旨
detail VieW a detail VieW b aquatic Industries, Inc. 13
ページ14に含まれる内容の要旨
* Base and plumbing may vary by model. 1 aquatic Industries, Inc. Figure 2 Final asseMbly Figure 1 Figure 3
ページ15に含まれる内容の要旨
installation instructions clean-uP: 1. Remove all construction residue and foreign materials. Wipe unit clean with a damp rag, otherwise staining may occur. 2. Plaster may be removed by scraping with the edge of a piece of wood or rigid plastic. Do not use metal scraper. For spots left by plaster or grout: rub lightly with a liquid detergent (Spic and Span or similar) on damp cloth or sponge. 3. Do not use abrasive cleaners, scouring powders, steel wool, wire brushes or anything else th
ページ16に含まれる内容の要旨
oPeration oF syMPhony WhirlPools jet oPerations: All Symphony Series jets are removable, and can simply be put into the dishwasher for easy cleaning. (Note: use top rack and remove before drying cycle.) syMPhony WhirlPool jets The Symphony Series uses spinning back jets and directional jets to provide an invigorating hydrotherapy experience. aquatic directional jet: 10a • t o adjust pressure (see diagraM 10a) : 1. grasp the outer ring of the jet. 2. Turn the outer ring counter clockwise t
ページ17に含まれる内容の要旨
oPeration oF syMPhony WhirlPools WhirlPool oPerations: Your whirlpool bathtub features a built-in circulating system that mixes the bath water with air and pumps the mixture back into the bathtub creating the hydromassage action. Because it is a bathtub, it must be drained after each use. The circulating system mixes air and water and must never be operated unless the bathtub is filled as described in the section entitled “Before Your First Use.” beFore your First use: • Make sure the b
ページ18に含まれる内容の要旨
oPeration oF syMPhony WhirlPools WhirlPool oPerations (continued): 3. do not operate the whirlpool system if: • The bathtub is not filled to required levels above jets. • You are pregnant (until you have consulted your doctor). • You are taking medications or drugs that may make you drowsy. • You are drinking any form of alcohol. • You are using soap or bubble bath. This may cause over-foaming, collect in and eventually clog the system. It is okay to use these after the whirlpool syst
ページ19に含まれる内容の要旨
Maintenance and care initial cleaning: Before tub is used, the whirlpool system should be cleaned and disinfected. Remove all debris and clean tub before putting whirlpool into service. DO NOT USE ABRASIvE CLEANERS ON THE ACRYLIC FINISH. Use a non-abrasive detergent and rinse well after cleaning. • Fill the tub with HOT water to a level 2” above the highest jet. • Add 2 teaspoons of low-sudsing automatic dishwashing detergent and no more than 4 ounces of household bleach to the water
ページ20に含まれる内容の要旨
Maintenance and care surF ace scratch reMoV al: Minor scratches may be removed by polishing your tub with a non-abrasive car polish, followed by buffing. Deeper scratches can be removed by: • Sanding with wet 400 grit sandpaper. • Sanding with wet 600 grit sandpaper. • Sanding with wet micro-grit sandpaper. • Buff out using car polish. reP air: the installation and service of your whirlpool bath should be performed only by a qualified service technician. remember when contacting your
