ページ1に含まれる内容の要旨
Rearview Mirror with 4.5" Color LCD with
Navigation and 2 Camera inputs
Model: LCMR5RP
Installation Manual
Features:
• Rearview Mirror with 4.5" LCD
• Rearview Camera Input
• Interior Camera Input
• Navigation Input
• NTSC /PAL Camera Compatible
ページ2に含まれる内容の要旨
Cautions! The product is intended to assist in safe driving and to allow the driver to have a broader rearview while the vehicle is in reverse. You, as the driver, are solely responsible for the safe operation of your vehicle and the safety of your passengers according to the country and their local traffic regulations. Do not use any features of this system to the extent it distracts you from safe driving. Your first priority while driving should always be the safe operation of your
ページ3に含まれる内容の要旨
TABLE OF CONTENTS Cautions! 1 Preface 3 WARNING 3 Packing list 3 1.Installation Instructions 4 2.Signal Inputs 5 3.Controls and Indicators 7 Specifications 9 Maintenance 10 Troubleshooting 11 Illustration of connections 12 2
ページ4に含まれる内容の要旨
Preface This replacement mirror /monitor can display up to 3 different video inputs. The inputs are Navigation, Rear observation camera and Interior observation camera. Not all rearview mirrors attach to the vehicle with the same style mount. Please consult the application guide for the appropriate mounting bracket for your vehicle or call Tech Service at 800-225-6074. There is a blind spot that exists at the back of a vehicle while the vehicle is in reverse. Equipped with a camera
ページ5に含まれる内容の要旨
1. Installation Instructions (1) Mount the mirror/monitor a) Remove the original factory mirror. (Do not use excessive force when removing factory mirror.) Check to make sure that the factory mirror mount you remove matches the mirror mount on the replacement mirror. If it does not match, consult the application guide or call Technical Service at 800-225-6074. b) Slide the receiving bracket on the back of the new mirror stalk onto the windshield mounting butt
ページ6に含まれる内容の要旨
(4) Electrical Connections: Connect the 4 wires in the following manner. a) Red wire - 12 volt constant (positive) b) Black wire - Chassis ground (negative) c) Blue wire - 12-volt ignition (12 volt with ignition on) d) Green wire - Reverse light switch (12 volt when vehicle is in the reverse gear) WARNING: Observe polarity when connecting the wires. Figure 2 2. Signal Inputs The signal input connections for the system include: (1) Rear Camera: Plug t
ページ7に含まれる内容の要旨
Some operators may find that leaving the Navigation Image on the LCD monitor at all times becomes a distraction while operating their motor vehicle. For the convenience of those operators, a ‘Display Timer Slide Control Switch’ has been added to the mirror. A. When the Slide Control Switch is moved to the far right end position, the Navigation image will remain on at all times. B. When the Slide Control Switch is moved to the far left end position, the Navigation image will remain off at
ページ8に含まれる内容の要旨
Figure 5 3. Controls and Indicators Figure 5 shows the function controls of the rear view mirror. A: 4.5" LCD Panel B: Rearview Mirror Glass C: “+”Button (optional Navigation System required) Incrementally increase volume level of the navigation voice command when pressed. Note: Will only operate when the Navigation System remote control is removed from the cradle. D: “CAM”Button - If you have installed an optional interior view camera, pressing the C
ページ9に含まれる内容の要旨
Note: Will only operate when the Navigation System remote control is removed from the cradle. F: “-” Button (optional Navigation System required) Incrementally decrease volume level of the navigation voice command when pressed. Note: Will only operate when the Navigation System remote control is removed from the cradle. G: Internal Speaker H: LCD Brightness Control I: Internal Infra-RED Receiver for use with Navigation System Remote Control. J: Power LED (Red when Power is on) K:
ページ10に含まれる内容の要旨
Specifications General Power Supply 12VDC Power Consumption <12W Current Draw <800mA Video Input 1Vp-p/ 75 Impedance Audio Input <=1V Audio Power Output 0.5W × 1 (16 Ω) Operating Temperature Range 0 ℃ to 50 ℃ Display System Screen 4.5” TFT Color LCD Brightness 400 cd/ ㎡ Contrast Ratio 150 : 1 Backlight Life 10000 hours Resolution 960 ×234 Video Format PAL/NTSC auto detect Display Format 16 : 9 Navigation input RGB 9
ページ11に含まれる内容の要旨
Maintenance Though your Rearview mirror requires little care, you can still maintain its condition and performance by following the procedures below. • Keep your system away from excessive moisture, extreme heat or cold, and magnetic fields. • Keep liquids away from the display and mirror. • To avoid damage, do not place external devices or other objects on the top of the mirror. • Occasionally wipe the rearview mirror set with a soft, damp cloth. • Occasionally clean the surface
ページ12に含まれる内容の要旨
Troubleshooting Symptoms Solutions 1. Check the installation-wiring diagram. 2. Ensure that the parallel red and black line from The ON/OFF signal light is the control box is connected properly. not on after the car is started? 3. Check for 12 volts on the blue wire while the ignition on. 1. Check the rearview Camera lens. 2. Check the rearview Camera wiring and connection. 3. Check the cable from the rearview mirror is No video signal appears while connected to
ページ13に含まれる内容の要旨
Illustration of Connections Figure 6 12
ページ14に含まれる内容の要旨
© 2005 Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, N.Y. 11788 128-7381 13
