ページ1に含まれる内容の要旨
TOSHIBA
DISK PRODUCTS DIVISION
SD-W1111
DVD-RAM DRIVE
PRODUCT SPECIFICATION
JUNE 1999
REV. 1.0
Specifications are subject to change without notice
DOCUMENT NUMBER
12043
ページ2に含まれる内容の要旨
A 0 17 2 TOSHIBA DVD-RAM SD-W1111 ‘99/06/26 Version 1.0 This drive adopts RPC-II for its “ Standard Specification Model ” . This DVD-R A M Drive adopts RPC-II, the Phase II System of RPC (Regional Playback Control) for “ ” A A M Drives but also PC systems installing DVD-R A M To playback a DVD-Movie Software with the Regional Code specified by using a DVD-R A M Drive with RPC-II does not support RPC-II, if the "RPC-II (Standard Specification) Drive" is used in combination, DVD-Movie Softwares w
ページ3に含まれる内容の要旨
A 0 17 2 TOSHIBA DVD-RAM SD-W1111 ‘99/06/26 Version 1.0 Precaution This equipment ( optical disc drive) handled under the conditions out of product specifications may cause injury, heat generation, trouble, erroneous operation and performance degradation, so, care will be , and proper handling according to the precautions shown below will be required. In case of necessary mishandling without keeping the cautions, safety, reliability and performance of the product are not guaranteed. For systems
ページ4に含まれる内容の要旨
A 0 17 2 TOSHIBA DVD-RAM SD-W1111 ‘99/06/26 Version 1.0 1. Scope ................................ ................................ ................................ ................................ .................... 6 2. ................................ ................................ ................................ ................................ ................ 6 3. ................................ ................................ ................................ ............. 7 4. ....
ページ5に含まれる内容の要旨
A 0 17 2 TOSHIBA DVD-RAM SD-W1111 ‘99/06/26 Version 1.0 15. ................................ ................................ ................................ ........................... 30 15.1 ................................ ................................ ................................ ................................ .. 30 15.2 ................................ ................................ ...................... 30 15.3 ................................ ...............................
ページ6に含まれる内容の要旨
A 0 17 2 TOSHIBA DVD-RAM SD-W1111 ‘99/06/26 Version 1.0 1. Scope 2. Features 2.6 • ing 650 nm short-wavelength laser, 0.74 μ m single spiral land and groove tracking and Z-CLV G B ( High data recording rate • P hase chang e recording technology to write data directory into the media ) • te • • c h e .7 W ( • Owing to the low power consumption design to operate using +5V single power supply, no exclusive • ( 7 ) • . • ( 8 ) • • Powerful error correction ability by employing the era
ページ7に含まれる内容の要旨
A 0 17 2 TOSHIBA DVD-RAM SD-W1111 ‘99/06/26 Version 1.0 3. External views and dimensions External views: f Page 7 Product Specification ront bezel) 146.0 x 203.0 x 41.3 (mm) (W x D x H) (Except for -0 OD-
ページ8に含まれる内容の要旨
A 0 17 2 TOSHIBA DVD-RAM SD-W1111 ‘99/06/26 Version 1.0 4. Basic specifications • 5.25 ” 30 20 10 • B = 2 1M B = 2 1K B = 2 1 * s for R rsion 1.0 Part 1 2 3 2.42 GBytes* x 1 ( C * 2.42 x 2 ( C s for R rsion 1.0 Part 1 4.38 Single 7.96 Dual 4 DVD-R ( Read only) * CD-ROM V Y 5 CD-I* 4 CD-R ( Read only) * 4 Read only) * *1: *2: 2.32GB : eatures may occur. *4: Depending on the feature of a recording unit that records data, playback function may not be *5: • • al 1,028 – 1
ページ9に含まれる内容の要旨
A 0 17 2 TOSHIBA DVD-RAM SD-W1111 ‘99/06/26 Version 1.0 • Average seek time ( ) 120 typ.) 210 ( typ.) CD-ROM ( typ.) • 1 180 * ( typ.) 1 260 * ( typ.) 2 CD-ROM 1 7 0 * ( typ.) *1 *2 • 15 * 7.0 s CD-ROM 7.0 s • 1.0 s ( idle to active ) 2.0 s ( ) • 1 • 32 • Logical sector size 2 • M • Page 9 Product Specification (Time until the unit responds to the command after power turns on.) Less than 1.0s Initialize time Bytes 2 Data buffer KBytes KBytes (ECC block unit) Physical re
ページ10に含まれる内容の要旨
A 0 17 2 TOSHIBA DVD-RAM SD-W1111 ‘99/06/26 Version 1.0 5. Power supply specifications 5.1 Input power supply power supply cable that is long and thin, power supply voltage is drop and out of the Wire Ω 57.4 0.344 23.7 0.142 56.3 0.338 22.2 0.133 5.2 Power consumption 6.7W 6.0W Less than 11.0W 1.0W 5.3 Allowable ripple voltage 6. Mechanical specifications 6.1 Dimensions ( 3 . ) 6.2 Mass ( 6.3 Disc loading 1) load/unload switch 2) 3) 4) 6.4 Optical head auto-lock mechanism To protect the optic
ページ11に含まれる内容の要旨
A 0 17 2 TOSHIBA DVD-RAM SD-W1111 ‘99/06/26 Version 1.0 • • • After “ ” When transporting, transport the drive after performing the steps above and turning off the power. 7. Reliability specifications 7.1 Error rate – 15 Read error rate – 6 Seek error rate – 15 Read error rate – 6 Seek error rate CD-ROM – 15 – 12 – 6 Seek error rate 7.2 Life 1 100,000 H 5 , 436 s : : 8. Environmental specifications 8.1 Temperature – 10 to – 40 to 6 5 /h Page 11 Product Specific
ページ12に含まれる内容の要旨
A 0 17 2 TOSHIBA DVD-RAM SD-W1111 ‘99/06/26 Version 1.0 8.2 Relative humidity 8 to 80% RH 5 to 95% RH 5 to 95% RH 3 ) 8.3 Vibration(5 to 300 Hz) 2 2 . 0 2 9 . 0 2 9 . 8 0 8.4 Shock(Half sine wave 11 msec., interval 2 sec., 5 cycle) 2 14 . 0 2 0 8.5 Altitude 0 to 3,000 m 0 to 12,0 00m 8.6 Static electricity 6 K 15 upp 8.7 Acoustic noise 45 dB (Max.) • 1 • JIS A correction • 8.8 Applicable regulations 3rd 3rd ) CE standard : 1994 class B 4 5 5 Page 12 Product Specification : 1995 EN610
ページ13に含まれる内容の要旨
A 0 17 2 TOSHIBA DVD-RAM SD-W1111 ‘99/06/26 Version 1.0 3 Page 13 Product Specification : 1994 EN61000-4-11 : 199 EN61000-4-8 : 1996 EN61000-4-6 -0 OD-
ページ14に含まれる内容の要旨
Head A 0 17 2 TOSHIBA DVD-RAM SD-W1111 ‘99/06/26 Version 1.0 9. Block diagram Page 14 Product Specification Sensor Loading unit DRAM(2Mbit) DISC TC203C620 DRAM(16Mbit) Spindle motor DVD-RAM/ROM LD controller TLS1040 processor Pre- Lens amp Ho- actuator SPC7426 RF-amp Loading LD motor F452658 SCSI SM9403 Linear motor Authent I/F Servo controller SM9103 ication processor Servo-amp Pre-amp 40MHz LD controller for CD MPC17A66 TC9449AF Actuator driver x 2 CD-ROM decoder MPC17A66 CD processor Linear
ページ15に含まれる内容の要旨
A 0 17 2 TOSHIBA DVD-RAM SD-W1111 ‘99/06/26 Version 1.0 10. Mounting 10.1 Mounting Flatness deviation under 0.5mm Use screws of which length inside the drive should be more than 2.5mm and less than 3.5 mm from the drive frame surface. Keep this gap less than 0.5mm . Before fixing After fixing Page 15 Product Specification The following shows an example mounting on a personal computer or a sub system. Mount the drive using four M3 tapping holes bottom and two M3 tapping holes on each side.
ページ16に含まれる内容の要旨
A 0 17 2 TOSHIBA DVD-RAM SD-W1111 ‘99/06/26 Version 1.0 10.2 Mounting direction n (When installing vertically, the allowable slants toward the top plate bottom 15 ° max 15 ° max 15 ° max 10 ° max 10 ° max Page 16 Product Specification Within 10° Front/rear directions: should be 0°.) Within ±15°. : Left/right directions Allowable slants (Refer to the drawing.) 80mm disc, vertical direction installation is not allowed.) (When using a Horizontal or vertical installation Install direction -0
ページ17に含まれる内容の要旨
A 0 17 2 TOSHIBA DVD-RAM SD-W1111 ‘99/06/26 Version 1.0 10.3 Notes on mounting • c the drive • Keep more than 0.8mm clearance around the top cover in order to secure absorbing shock and Page 17 Product Specification vibration. and mounting metal parts. onvection around Keep more than 5mm clearance to circulate an adequate amount of air by -0 OD-
ページ18に含まれる内容の要旨
A 0 17 2 TOSHIBA DVD-RAM SD-W1111 ‘99/06/26 Version 1.0 • • surface . Drive Frame M3 screw 2.5-3.5mm Page 18 Product Specification drive frame Use screws of which length inside the drive should be more than 2.5mm and less than 3.5 mm from the caving in the top plate. ) 150gf 1.5N : (under Do not apply force -0 OD-
ページ19に含まれる内容の要旨
A 0 17 2 TOSHIBA DVD-RAM SD-W1111 ‘99/06/26 Version 1.0 11. Front bezel 11.1 Standard Bezel Emergency disc eject hole Load/Unload switch LED: “ROM” “RAM” “BUSY” • Load/Unload switch: • Emergency disc eject hole: 15.3 ) • LED: “ BUSY ” “ ” (green): “ ROM ” 11.2 LED lighting Closing the tray, “ ” A disc is loaded and “ Ready ” , “ ” LED or “ ROM ” LED turns on “ BUSY ” “ ” “ ” “ ” ’ “ Ready ” all “ ” “ ” “ ” Page 19 Product Specification BUSY RAM or ROM LEDs turn off LEDs turn off. , all t
ページ20に含まれる内容の要旨
A 0 17 2 TOSHIBA DVD-RAM SD-W1111 ‘99/06/26 Version 1.0 ’ s all “ ” “ ” “ ” “ BUSY ” “ ” SEEK “ ” “ BUSY ” 1.6 s “ ” “ ROM ” “ BUSY ” 2.0 s “ ” Page 20 Product Specification BUSY cycle. LED blinks on about 2.0sec LED turns on and While playing a CD audio track, (6) BUSY 1.6sec cycle. LED blinks on about LED turns on and RAM While executing FORMAT command, (5) START / STOP UNIT GET PERFORMANCE SET READ AHEAD READ HEADER SEND DIAGONOSTIC VERIFY WRITE & VERIFY WRITE READ REASIGN Command BUS
