Caution The DX3000 Series DVR has an unmarked lock Changing Password button to restrict unauthorized use of the re- 1. Turn the Password Lock feature OFF (refer to corder. The lock button will work only as long as Remove Turning Password Lock On and Off ). no one discovers its function. Since you may need to make the manual accessible to others, 2. Press the LOCK button for five seconds. the lock button’s location and operation are NOT The Password Lock menu appears. this page documented in the
ページ2に含まれる内容の要旨
® DX3000 Series Digital Recorder Installation/ Operation Manual C681M-D (2/02) U ® L LISTED Pelco • 3500 Pelco Way • Clovis, CA 93612-5699 USA • Pelco Online @ www.pelco.com In North America and Canada: Tel (800) 289-9100 • FAX (800) 289-9150 • DataFAX (800) 289-9108 International Customers: Tel +1(559) 292-1981 • FAX +1(559) 348-1120 • DataFAX +1(559) 292-0435 PelcoEurope BV • Dillenburg Center, Dillenburgstraat 7C • 5652 AM Eindhoven • The Netherlands Tel +31(40) 251-9870 • FAX +31(40) 251-983
ページ3に含まれる内容の要旨
CONTENTS Section Page IMPORTANT SAFEGUARDS AND WARNINGS ................................................................ 5 OVERVIEW ........................................................................................................................6 DESCRIPTION ........................................................................................................... 6 MODELS ....................................................................................................................
ページ4に含まれる内容の要旨
TCP/IP SETTING (DX3016 Models Only) ................................................................. 49 TIME AND DATE DISPLAY ....................................................................................... 49 DISPLAY MODE ............................................................................................... 49 CHARACTER SIZE ........................................................................................... 50 CLOCK LOCATION..............................................
ページ5に含まれる内容の要旨
LIST OF ILLUSTRATIONS Figure Page 1 Front Panel Controls, DX3009 Models ..............................................................7 2 Front Panel Controls, DX3016 Models ..............................................................7 3 Rear Panel Connectors, DX3009 Models .........................................................10 4 Rear Panel Connector, DX3016 Models ...........................................................10 5 Equipment Connections (DX3009 Model Shown) ..................
ページ6に含まれる内容の要旨
IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and servicing should only be done by qualified service personnel and con- form to all local codes. 2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6 or 6P enclo- sure, it is designed for indoor use only and it must not be installed where exposed to rain and moisture. 3. The installation method and materials should be capable of sup
ページ7に含まれる内容の要旨
OVERVIEW DESCRIPTION The DX3000 Series Digital Video Recorder (DVR) is a high-quality digital recorder that combines the functions of a recorder and multiplexer into one unit. With the number of cameras in systems increasing, the combination of a video recorder with a multiplexer has become standard. In pursuit of the high-quality image playback char- acteristic of digital recording and as a way to make the recording operation more ideal, the DX3000 Series DVR includes versatile multiplexer func
ページ8に含まれる内容の要旨
MODELS DX3009-030 Nine-channel digital video recorder, 30 GB hard drive, simplex operation (cannot record and play back video at the same time), 120/230 VAC, NTSC DX3009-060 Same as the DX3009-030, except has 60 GB hard drive DX3016-060 Sixteen-channel digital video recorder, 60 GB hard drive, simplex opera- tion (cannot record and play back video at the same time), 120/230 VAC, NTSC DX3016-120 Same as the DX3016-060, except has 120 GB hard drive FRONT PANEL CONTROLS 1 2 3 4 56 7 CAMERA CLEAR/ E
ページ9に含まれる内容の要旨
3. Recording indicators TIMER REC indicator This light illuminates during timer recording and timer recording standby mode. The POWER button does not work when the TIMER REC indicator is lit. To turn on the power when the TIMER REC indicator is lit in the standby mode, press the TIMER REC button. M-DET indicator The light illuminates whenever the motion detection setting is ON in the Initial Set Up menu. When the setting is ON, the light goes out if you are in a programming menu. PRE ALARM REC i
ページ10に含まれる内容の要旨
8. Mode indicators ACCESS indicator This light flashes when the hard disk drive or peripheral recording devices are being accessed. LOCK indicator This light illuminates when the LOCK button is set to ON. 9. Menu buttons Press one of the buttons to display each menu. Press again to exit the menu. INFO button Press this button to display the Information menu. SET UP button Press this button to display the Menu Setting menu. COPY button Press this button to display the Copy Selection menu. This bu
ページ11に含まれる内容の要旨
18. REMOTE communication button and indicator lights (DX3016 Models Only) Not used. REAR PANEL CONNECTORS 1 2 3 4 5 6 AUDIO MIC CAMERA IN VIDEO OUT IN 1 23456789 CAMERA OUT 1 234 56789 Y/C OUT ON OFF GND GND SCSI ALARM IN TERMINATION RS-232C RESET 1 23456789 SCSI 7 8 9 10 11 Figure 3. Rear Panel Connectors, DX3009 Models 2 1 3 4 5 6 AUDIO CAMERA IN VIDEO OUT 1234 5678 9 10 11 12 13 14 15 16 IN CAMERA OUT 1234 5678 9 10 11 12 13 14 15 16 OUT Y/C GND GND ON OFF MIC SCSI ALARM IN ETHERNET RESET
ページ12に含まれる内容の要旨
6. AC power socket This socket is for a 100-240 VAC power cord. 7. RS-232C connector This is where a PelcoNet™ Transmission System can be connected for remote view- ing and control of cameras. 8. ALARM IN terminals These are input terminals for alarm signals. GND terminals These are earth ground terminals for the ALARM IN terminals. Use only the terminal screws provided with this unit; otherwise, the recorder could be damaged or connec- tions may be poor. 9. I/O terminals GND terminals These are
ページ13に含まれる内容の要旨
INSTALLATION 1. Connect cameras, monitor, and audio equipment to the recorder as shown in Figure 5. MONITOR To S(Y/C) IN To peripheral loudspeaker or monitor terminal through AUDIO IN terminal Either cable can be connected. CAMERA #1 Up to 9 cameras To CAMERA IN 1 terminal To VIDEO OUT or •• • S(Y/C) OUT To MIC terminal MICROPHONE terminal AUDIO MIC CAMERA IN VIDEO OUT IN 1 23456789 CAMERA OUT 1 234 5678 9 Y/C OUT To AUDIO OUT terminal GND GND ON OFF SCSI ALARM IN RESET TERMINATION RS-232C 123
ページ14に含まれる内容の要旨
POWER ON/POWER OFF/ ALARM OUT/MODE OUT Output terminal ALARM IN/REC/CLOCK ADJ • Output Circuit Input terminal 5V • Input Circuit 5V 10kΩ 22kΩ Input Output terminal terminal 0.047µF GND terminal GND Figure 7. Schematics for Alarm Input and Output Terminals 3. Optional. Connect the recorder to a remote source for turning the unit on/off. By using the POWER ON/POWER OFF terminals, it is possible to turn on/off the
ページ15に含まれる内容の要旨
The REC input terminal is used to start recording. Refer to Series Recording in this step for more information. The input is active when a ground or low voltage signal is applied. The in- put is non-active when the terminal is open. The MODE OUT output terminal is used to indicate the status of the recorder (refer to Mode Out in the Programming section for more information). It can also be used to turn on an- other recorder (refer to Series Recording in this step for more information). The outpu
ページ16に含まれる内容の要旨
5. Optional. Connect peripheral recording devices. By connecting peripheral recording devices to the recorder through the SCSI interface (SCSI-II half-pitch 50-pin), storage space can be increased and archiving and copying functions can be performed. To increase storage space, up to two (DX3009-060, DX3016-060, and DX3016-120) or three (DX3009-030) peripheral hard disk drives (maximum of 34 GB per unit for DX3009 models or 103 GB per unit for DX3016 models) can be added to supplement the built-i
ページ17に含まれる内容の要旨
6. Connect the power cord to the recorder, and then plug the power cord into a wall socket. 7. Turn on power to peripheral recording devices first, and then turn on the power to the recorder. Power to the cameras and monitor can be turned on before or after turning on the recorder. If there are no peripheral devices connected to the SCSI terminal, the installation is complete. Proceed to the Programming section. If there are peripheral devices connected to the SCSI terminal, the recorder automat
ページ18に含まれる内容の要旨
REMOVING A HARD DRIVE(S) This section applies only to devices removed from ID1-ID3. 1. Turn off power. 2. Remove the hard drive(s). 3. Turn on power. The screen to the left appears. ID5:RDD PWR-OFF CONFIG. BOOT UP DELAY 00 4. Make sure that any connected device is recognized correctly. 5. Turn the JOG dial to select CONFIG., and then turn the SHUTTLE ring to the right twice. The recorder starts configuring. When CONFIG. is selected, the recorder sa
ページ19に含まれる内容の要旨
PROGRAMMING SUB MENU (1) SUB MENU (2)
ページ20に含まれる内容の要旨
SUB MENU (2) SUB MENU (1) IMAGE QUALITY HIGH CH PRI FILD CH PRI FILD MAX REC FIELDS 15F 1 1 6 1 DEFINE GROUP SETTING 2 1 7 1 A-REC DURATIOM 1M 3 1 8 1 RECORD ALARM SEP 4 1 9
