ページ1に含まれる内容の要旨
Digital
High Definition Receiver
7
Introduction
HD-S23
11
Connections
15
Menu Navigation
OWNER'S MANUAL
27
Quick Control
Appendices 31
©2003 Toshiba Corporation
1
ページ2に含まれる内容の要旨
Precautions WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. TO PREVENT ELECTRIC SHOCK, DO NOT OPEN THE COVER. REFER SERVICING TO QUALIFIED PERSONNEL ONLY. This unit is not disconnected from the AC power source as long as it is connected to the wall outlet, even if the unit itself has been turned off. NOTE The rating label and the safety caution are on the rear of the unit. Power cord cautions When plugging in or unplugging the p
ページ3に含まれる内容の要旨
6. Places without adequate air circulation. On top of a carpet or sofa. In a bookcase. Near materials such as curtains, etc. 7. Extremely hot or cold places The operating temperature range of this unit is 5℃ to 40℃ 8. Do not place a flower vase or cloth on top of this unit. Please pay attention to the following items when using this unit. Failure to do so may result in damage to the unit or electric shock. 1. Connect the power plug to AC 100-240V 50/60Hz 2. Unplug the power cord
ページ4に含まれる内容の要旨
Types of Power Plug Australia 3-prong power plug imagine to be Power cord must be used in paste here by Zinwell! Australia only Singapore 3-prong power plug imagine to be Power cord must be used in paste here by Zinwell! Singapore only 4
ページ5に含まれる内容の要旨
TABLE OF CONTENTS TABLE OF CONTENTS PRECAUTIONS.....................................................................................................................................................................2 TYPES OF POWER PLUG ..................................................................................................................................................4 TABLE OF CONTENTS ...............................................................................................
ページ6に含まれる内容の要旨
SOFTWARE UPDATE ..................................................................................................................................................22 TIME SETUP................................................................................................................................................................23 EDIT CHANNEL....................................................................................................................................................
ページ7に含まれる内容の要旨
Introduction INTRODUCTION The HD-S23 Digital Terrestrial HDTV Receiver opens up to a new world of free-to-air terrestrial HDTV and SDTV programmes. The receiver can receive channels from both VHF band and UHF band TV station’s signals. All the major terrestrial free-to-air station numbers currently available in your area are listed in the on-screen menu. To watch a channel, simply select the channel number and you will be accessing a wide range of high quality digital programmes.
ページ8に含まれる内容の要旨
IDENTIFICATION OF CONTROLS Front Panel LED Display Four-digit channel number, time or video format Two LEDs: Green for power; Red for signal indication (OFF –signal captured, ON –no signal) MENU / ENTER (Please refer to pp. 17 for more details) EXIT / V.OUTPUT → OUT1 & OUT2 description (Zinwell) Direction Keys Power on / off Rear Panel AC MAINS SUPPLY (OUT
ページ9に含まれる内容の要旨
Introduction Remote Control The buttons on the remote control are described as follows: Numeric Buttons For entering channel number or password POWER Switches the receiver between ON and STANDBY modes INFO Displays I-Plate providing information about the current channel AUDIO Toggles between multi-lingual Audio soundtracks MENU Activates the On-Screen Menu LIST Displays the complete channel/program list FAV Displays the Favourite channel list Dire
ページ10に含まれる内容の要旨
Loading batteries Operating with the remote control 1. Open the Cover 2. Insert batteries (AAA size) Make sure to match the + and – on the batteries to the marks inside the battery compartment. 3. Close the cover. Notes on batteries Improper use of batteries may cause battery leakage and corrosion. To operate the remote control correctly, follow the instructions below. Do not insert batteries into the remote control in the wrong direction. Do not charge, heat, open, or short-c
ページ11に含まれる内容の要旨
UConnections Read this chapter first to make all necessary preparations • Connecting to Audio Video Devices • Connecting to SDTV (without Component Inputs) • Connecting to SDTV (with Component Inputs) and VCR • Connecting to HDTV • Connecting to HDTV and VCR 11
ページ12に含まれる内容の要旨
CONNECTING TO AUDIO VIDEO DEVICES For the best video/audio quality, use the higher quality Y/Pb/Pr or S-Video cables if available. Always remember to disconnect the receiver from the power source, when connecting or disconnecting the cable to the UHF/VHF antenna. Notes: (a) If your TV supports 1080i / 720p / 576p / 576i video input formats, please use the receiver’s OUT2 video connectors. You may use the V.FORMAT button on the remote control to switch between four video output
ページ13に含まれる内容の要旨
Connections Connecting to SDTV (without Component Inputs) Connecting to SDTV (with Component Inputs) and VCR 13
ページ14に含まれる内容の要旨
Connecting to HDTV Connecting to HDTV and VCR 14
ページ15に含まれる内容の要旨
UMenu Functions in the Menu. • Menu Map • Initial Setup • Main Menu • Installation - Auto Scan - Quick Scan - Manual Setup - Reset Data • Program • Electronic Program Guide • System - Password - Video Setup - Audio Setup - Software Update - Time Setup • Edit channel - Fav. & Lock - Parental Guidance (Rating) • Profile - Transparency - I-Plate Setup - Information 15
ページ16に含まれる内容の要旨
MENU MAP MENU MAP 16
ページ17に含まれる内容の要旨
Menu Navigation INITIAL SETUP If your service provider or antenna installer has already installed your TV system to receive terrestrial TV programmes, do not change any connections of those devices or installation settings unless it is absolutely necessary. If your receiver has not been configured by your service provider or system installer, then it will not be set up for any specific channel or frequency when powered on for the first time. ● Initial Screen – The first time the
ページ18に含まれる内容の要旨
INSTALLATION On the main menu, select “INSTALLATION” and key-in your password to enter the Installation page. Note: The default password is 0000. Please refer to pp. XX to change the password. AUTO SCAN The steps required to automatically program the receiver are outlined as below: ● Highlight “AUTO SCAN” and press the “ENTER” button to start channel search. ● The receiver starts scanning from channel 2 to channel 69. The status bar shows the progress being made. ●
ページ19に含まれる内容の要旨
Menu Navigation MANUAL SETUP ● On the Installation page, highlight “MANUAL SETUP” and press the “ENTER” button. ● Select channel number. Be sure you know the channel number and its RF frequency. You may refer to Digital TV channel table on Appendix 1. ● Press “ ▼” button to highlight “Frequency”, “Bandwidth” and “Priority” to make sure the parameters are correct, then press “ ▼” button to highlight “Start Scan” and press the “ENTER” button to start scanning. No
ページ20に含まれる内容の要旨
PROGRAM ● On the main menu, select “PROGRAM” to enter the program list. ● Use the “ ▲” and “ ▼” buttons to browse through the channel numbers and names Note: Alternatively, when you are watching a Digital TV channel (without any menu on screen), you can press the “LIST” button on the remote control twice to call up the program list. ELECTRONIC PROGRAM GUIDE ● To call out the program guide of the specific channel, highlight th
