ページ1に含まれる内容の要旨
U514Aen 98/2/18 4:25 AM Page 1
PLASMA MONITOR
OWNER’S MANUAL
MODELS: 42PM1M 42PM1M-UC
42PM3MV 42PM3MV-UC
50PM1M 50PM1M-UC
Please read this manual carefully and completely before
operating your Monitor.
Retain this manual for future reference.
Record model number and serial number of the Monitor in the
spaces provided below.
See the label attached on the back cover and relate this infor-
mation to your dealer if you require service.
Model Number :
Serial Number :
ページ2に含まれる内容の要旨
U514Aen 98/2/18 4:25 AM Page 2 Warning/Caution Warning/Caution Warning/Caution WARNING/CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING/CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of s
ページ3に含まれる内容の要旨
Owner's Manual U514Aen 98/2/18 4:25 AM Page 3 Safety Instructions Safety Instructions Safety Instructions IMPORTANT SAFETY INSTRUCTIONS Important safety instructions shall be provided with each apparatus. This information shall be given in a separate booklet or sheet, or be located before any operating instructions in an instruction for installation for use and supplied with the appa- ratus. This information shall be given in a language acceptable to the country where the apparatus is intended
ページ4に含まれる内容の要旨
U514Aen 98/2/18 4:25 AM Page 4 Safety Instructions 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. Do not overload wall outlets. Overloaded wall outlets, loose When a cart is used, use caution when moving the or damaged wall outlets, extension cords, frayed power cart/apparatus combination to avoid injury from tip-over. cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in elec
ページ5に含まれる内容の要旨
U514Aen 98/2/18 4:25 AM Page 5 Contents Contents Contents Warinig/Caution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Time Setting Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3~4 Clock Setup . . . . . . . . . . . . . . . . . . . . . . . . . . .22 On/Off Timer Setup . . . . . . . . . . . . . . . . . . . . .22 Introduction Auto Off / Sleep Timer . . . . . . . . . . . . . . . . . . .23 Accessories . . . . . . . . . . . . . . . . . . . . . .
ページ6に含まれる内容の要旨
U514Aen 98/2/18 4:25 AM Page 6 Introduction Introduction Introduction What is a Plasma Display Panel (PDP)? A plasma display panel is the latest display technology and the best way to achieve flat panel displays with excellent image quality and large screen sizes that are easily viewable. The PDP can be thought of as a descendant of the neon lamp and it can be also be viewed as a series of fluorescent lamps. How does it work? PDP is an array of cells, known as pixels, which are comprised of 3
ページ7に含まれる内容の要旨
OK POWER MUTE POWER INPUT MULT IMEDIA MTS/ MENU ARC EXIT ENTER VOL VOL 123 456 789 APC 0 DASP SPLIT ZOOM A.PROG/ SLEEP MEMOR Y/ REVIEW/ ER ASE/ FCR/ REW PLAY FF RECORD STOP STILL U514Aen 98/2/18 4:25 AM Page 7 Introduction Accessories Accessories Ensure that the following accessories are included with your plasma display. If an accessory is missing, please contact the dealer where you purchased the product. 1.5V Owner’s Manual Batteries Remote Control Power Cord D-sub 15 pin Cable Controls Co
ページ8に含まれる内容の要旨
U514Aen 98/2/18 4:25 AM Page 8 Introduction Connection Options Connection Options - Connection panels shown may be somewhat different from your Monitor. AC INPUT 9 AUDIO AUDIO REMOTE CONTROL RGB OUTPUT COMPONENT INPUT 2 MONITOR OUTPUT R L R L COMPONENT INPUT 1 A/V INPUT RL R L (MONO) RS-232C INPUT HDMI/ VARIABLE AUDIO OUT EXTERNAL SPEAKER AUDIO INPUT RGB INPUT VIDEO AUDIO AUDIO VIDEO S-VIDEO (CONTROL/SERVICE) DVI(VIDEO) 1 2 3 4 5 6 7 8 1. RS-232C INPUT(CONTROL/SERVICE) PORT 8. VIDE
ページ9に含まれる内容の要旨
POWER U514Aen 98/2/18 4:25 AM Page 9 Introduction Remote Control Key Functions Remote Control Key Functions - When using the remote control, aim it at the remote control sensor on the Monitor. - Under certain conditions such as if the remote IR signal is interrupted, the remote control may not function. Press the key again as necessary. MUTE MUTE POWER POWER Switches the sound on or off. Turns your Monitor on or off. INPUT INPUT MULTIMEDIA MTS/ Selects source: RGB,HDMI, Not functional Compon
ページ10に含まれる内容の要旨
U514Aen 98/2/18 4:25 AM Page 10 Installation Instructions Installation Instructions Installation Instructions GROUNDING Power Supply Ensure that you connect the earth ground wire to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the Short-circuit unit by connecting it to telephone wires, lightening rods, or gas pipes. Breaker Desktop Pedestal Installation Desktop Pedestal Installation
ページ11に含まれる内容の要旨
U514Aen 98/2/18 4:25 AM Page 11 External Equipment Connections External Equipment Connections External Equipment Connections NOTE: All cables shown are not included with the monitor. VCR Stup VCR Stup - To avoid picture noise (interference), leave an adequate distance between the VCR and monitor. - Use the ISM Method (on the Special menu) feature to avoid having a fixed image remain on the screen for a long period of time. Typically a frozen still picture from a VCR. If the 4:3 picture format
ページ12に含まれる内容の要旨
U514Aen 98/2/18 4:25 AM Page 12 External Equipment Connections External External A/V Source Setup A/V Source Setup How to connect Connect the audio and video cables from the external equipment's output jacks to the set input jacks, as shown in the figure. AUDIO COMPONENT INPUT 2 MONITOR OUTPUT When connecting the set to external equipment, match the COMPONENT INPUT 1 A/V INPUT RL R L MONO VARIABLE jack colors (Video = yellow, Audio Left = white, and Audio VIDEO AUDIO AUDIO VIDEO AUDIO OUT S
ページ13に含まれる内容の要旨
U514Aen 98/2/18 4:26 AM Page 13 External Equipment Connections DTV DTV Setup Setup - To watch digitally broadcast programs, purchase and connect a digital set-top box. AUDIO AUDIO REMOTE CO CONTROL RGB OUTPUT R L R L CO RL RS-232C INPUT HDMI/ VARIABLE EXTERNAL SPEAKER VIDEO (CONTROL/SERVICE) DVI(VIDEO) AUDIO INPUT RGB INPUT AUDIO AUDIO OUT or or B R (R) AUDIO (L) HDMI OUTPUT DVI-DTV OUTPUT (R) AUDIO (L) RGB-DTV OUTPUT Digital Set-top Box How to connect Signal Component 1/2 RGB, HDMI
ページ14に含まれる内容の要旨
U514Aen 98/2/18 4:26 AM Page 14 External Equipment Connections PC PC Setup Setup NOTE: All cables shown are not included with the Monitor How to connect 1. To get the best picture quality, adjust the PC graphics card to 1024x768, 60Hz. But in 42PM3MV series, we recommend using 640x480, AUDIO REMOTE 60HZ for the PC mode. CONTROL RGB OUTPUT 2. Use the set’s RGB INPUT or HDMI/DVI (VIDEO) RS-232C INPUT HDMI/ VARIABLE (CONTROL/SERVICE) DVI(VIDEO) AUDIO INPUT RGB INPUT AUDIO OUT INPUT port fo
ページ15に含まれる内容の要旨
U514Aen 98/2/18 4:26 AM Page 15 External Equipment Connections Monitor Display Specifications (RGB / HDMI-PC ) Horizontal Vertical Horizontal Vertical Resolution Proposed Resolution Proposed Frequency(KHz) Frequency(Hz) Frequency(KHz) Frequency(Hz) 31.468 70.09 EGA VESA(XGA) 48.363 60.00 640x350 37.861 85.08 EGA VESA(XGA) 56.476 70.06 1024x768 31.469 70.08 DOS VESA(XGA) 60.023 75.02 720x400 37.927 85.03 DOS VESA(XGA) 68.677 85.00 31.469 59.94 VESA(VGA) VESA 54.348 60.05 35.000 66.66 Macintosh
ページ16に含まれる内容の要旨
U514Aen 98/2/18 4:26 AM Page 16 Basic Operation Basic Operation Basic Operation Turning the monitor On Turning the monitor On Turning on the set just after installation 1. Connect power cord correctly, the set is switched to standby mode. 2. Press the ON/OFF (or rr / I), INPUT SELECT button on the set or press the POWER, MULTIMEDIA, INPUT on the remote control and then the set will switch on. Turning on the set (power cord is still connected) If the set was turned off with the remote cont
ページ17に含まれる内容の要旨
U514Aen 98/2/18 4:26 AM Page 17 Basic Operation On Screen Menus Selection and On Screen Menus Selection and Adjustment Adjustment • Your monitor's OSD (On Screen Display) may differ slightly from what is shown in this manual. 1. Press the MENU button and then D D / E E button to select each menu. 2. Press the G G button and then use D D / E E / F F / G G button to display the available menus. PICTURE PICTURE SOUND TIMER TIMER SOUND Clock APC DASP Off timer ACC BBE On timer A
ページ18に含まれる内容の要旨
U514Aen 98/2/18 4:26 AM Page 18 Picture Adjustment Picture Adjustment APC (Auto Picture Control) APC (Auto Picture Control) - APC adjusts the Monitor to the best picture appearance. - If adjusting picture options (contrast, brightness, color, sharpness, or tint) manually, APC automatically changes to Off. 1. Press the APC button repeatedly to select the picture appearance setup option as shown below. Daylight Optimum Night time Off • You can also adjust APC in the PICTURE menu. • Daylight, O
ページ19に含まれる内容の要旨
U514Aen 98/2/18 4:26 AM Page 19 Picture Adjustment ACM (Active Color Management) ACM (Active Color Management) - Adjust the ACM to select the desired skin color option. - This function works in the following mode: VIDEO, COMPONENT1, 2, RGB-DTV, HDMI-DTV. - This feature is not operational with the XD Off feature. PICTURE PICTURE APC 1. Press the MENU button and then use D D / E E button to select the PICTURE menu. ACC 2. Press the G G button and then use D D / E E button to select ACM. Flesht
ページ20に含まれる内容の要旨
U514Aen 98/2/18 4:26 AM Page 20 Sound Adjustment Sound Adjustment DASP (Digital Auto Sound Processing) DASP (Digital Auto Sound Processing) - This function lets you enjoy the best sound without any special adjustment because the Monitor has the appro- priate sound options based on the program content. - If you adjust sound options (Treble and Bass) manually, DASP automatically changes to Off. 1. Press the DASP button repeatedly to select the appropriate sound setup as shown below. SRS TSXT Fla
