ページ3に含まれる内容の要旨
The OutBack Power Systems MX60 PV MPPT Charge Controller is ETL listed to UL1741 (Inverters, Convert- ers, Controllers, and Interconnection System Equipment for Use with Distributed Energy Resources). It is also in compliance with European Union standards EN 61000-6-1 and EN 61000-6-3 (see page 87). About OutBack Power Systems OutBack Power Systems is a leader in advanced energy conversion technology. Our products include true sine wave inverter/chargers, a maximum power point charge controlle
ページ4に含まれる内容の要旨
TABLE OF CONTENTS INTRODUC TION ........................................................................................................................................................................................ 6 INSTALLATION GUIDELINES AND SAFETY INSTRUCTIONS ............................................................................................. 7 Standards and Requirements .............................................................................................................
ページ5に含まれる内容の要旨
Absorb Time Limits .....................................................................................................................................................................47 Wakeup Mode ................................................................................................................................................................................48 (DATA) LOGGING .........................................................................................................
ページ6に含まれる内容の要旨
SCOPE The manual provides safety guidelines and installation information for the MX60 PV MPPT Charge Controller. It does not provide information about specifi c brands of solar panels and supplies limited information on batteries. Contact the supplier or manufacturer of the solar panels or batteries for further information. INTRODUCTION MX60 PV MPPT (Maximum Power Point Tracking) Charge Controller The OutBack MX60 PV MPPT Charge Controller off ers an effi cient, safe, multi-stage recharging p
ページ7に含まれる内容の要旨
INSTALLATION GUIDELINES AND IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS This product is intended to be installed as part of a permanently grounded electrical system as shown in the system confi guration sections of this manual with the following important restrictions: • The negative battery conductor should be bonded to the grounding system at only one point in the system. If a GFP (Ground Fault Protector) is present, the battery negative and ground are not bonded. • With the excep
ページ8に含まれる内容の要旨
WARNING - WORKING IN THE VICINITY OF A LEAD ACID BATTERY IS DANGEROUS. BATTERIES GENERATE EXPLOSIVE GASES DURING NORMAL OPERATION. Design the battery enclosure to prevent accumulation and concentration of hydrogen gas in “pockets” at the top of the enclosure. Vent the battery compartment from the highest point to the outside. A sloped lid can also be used to direct the fl ow of hydrogen to the vent opening. CAUTION - To reduce risk of injury, charge only deep-cycle lead acid, lead antimony
ページ9に含まれる内容の要旨
OPEN CIRCUIT VOLTAGE/WIRE AND DISCONNECT SIZING Maximum Open Circuit Voltage (Voc) • Voc is the unloaded voltage generated by the solar array. 141 VDC MX60 suspends operation to protect components 150 VDC max open circuit voltage with the coldest environment (although the MX60 shuts down at 141 VDC, it can absorb up to 150 VDC from the array; anything higher than 150 VDC will damage the MX60) • As every brand of panel is diff erent, be sure to know the manufacturer’s specifi cations. •
ページ10に含まれる内容の要旨
Figure 1 Field Wiring Connections and Surge Protection Use up to 2 AWG Battery Remote Temp (6.54 mm) wire and Sensor (RTS) RJ11 jack torque to 30-inch pounds/3.38 Nm at terminals. Programmable AUX Output Jack (supplies MATE/HUB up to 200mA @ 12 VDC RJ45 jack Chassis/Equipment If attaching to ply- Ground Lug wood, use a 1 5/8” wood screw to secure the MX60 at the top slotted hole and other screws as needed at interior bottom holes. PV+ PV- BAT- BAT+ Four-Position Terminal Block T
ページ11に含まれる内容の要旨
NOTES • An optional battery Remote Temperature Sensor (RTS) is recommended for accurate battery recharging (only one RTS is needed for multiple OutBack Series Inverter/Chargers and MX60 units when an OutBack HUB and a MATE are parts of the system). When one RTS is used, it must be connected to the component plugged into the Port 1 of the HUB. • AUX modes include powering a relay, LED indicator, and Piezo-buzzer or brushless fan. • The OutBack MATE can display a single MX60 or multiple MX60
ページ12に含まれる内容の要旨
Figure 2 MX60 WIRING DIAGRAM without ground fault protection—the ground conductors tie into the negative. 12
ページ13に含まれる内容の要旨
Figure 3 MX60 WIRING DIAGRAM with ground fault protection—the GFP/2 requires a separate ground bus bar. 13
ページ14に含まれる内容の要旨
BATTERY SYSTEM VOLTAGE • The MX60’s default setting is for a 12 VDC battery. • Change the setting after powering up the MX60 if a diff erent battery voltage is used. • The PV array voltage—which must not exceed 150 VDC open circuit—is automatically detected. KEY TO THE EXAMPLE DIAGRAMS Soft keys: (#1) (#2) (#3) (#4) Solid black indicates key is to be pressed: Down arrow will lead to the next screen: Up arrow points to one or more keys that will change a value: The keys correspond to any text
ページ15に含まれる内容の要旨
POWERING UP The MX60 power-up sequence fi rst activates the unit and brings up a series of screens; some screens allow the user to change the battery voltage. NOTE: Be sure the PV input and battery breakers are off before starting the power-up sequence. OFF SCREEN (this screen is initially blank at power up) With the PV array and battery breakers off , press and hold soft keys #1 and #3 and then turn on the battery breaker (see Figure 4). Battery Breaker Figure 4 NOTE: The battery voltage mu
ページ16に含まれる内容の要旨
Power-Up Screen Release both soft keys when the OutBack Power Systems OutBack 12V screen appears. The selected battery voltage appears in Power the upper right hand corner. The BATTERY VOLTAGE screen Systems MX60 will appear next. NOTE: The MX60 designation in the lower left corner will read MX60AU for Australian versions and MX60ES for Spanish versions. BATTERY VOLTAGE “^^” indicates the selected battery voltage. Press 12 24 36 48 60 the “ ” or soft keys to proceed to the ^^ PAS
ページ17に含まれる内容の要旨
Battery Voltage Screen Press the “ soft key to select a battery voltage. The BATTERY VOLTAGE MX60’s default values are based on a 12 VDC system. 12 24 36 48 60 Selecting a higher voltage system will change all the ^^ EXIT ENTER default values (e.g., the values will double with a 24 VDC system, triple with a 36 VDC system, etc.). “^^” indicates the chosen voltage. The MX60 will automatically accept the selected battery voltage if left unattended for 5 min- utes in this screen. After c
ページ18に含まれる内容の要旨
STATUS SCREEN The STATUS screen displays system information. See page 67 for detailed information of the diff erent Operational Modes. The optional OutBack MATE displays MX STATUS screens for convenient distant viewing from the installation location of the MX60. Please see page 71 to view the MX screens dis- played on the MATE. The PV voltage will slowly rise to the battery voltage level even when the PV breaker is off – this is normal as the PV capacitor charges up. PV Input Voltage Batte
ページ19に含まれる内容の要旨
PREPARING FOR RECHARGING Turn the PV input breaker on. The MX60 PV 113 V Bat 12.5 V automatically detects the PV input voltage. 00.0 A 00.0 A Watts 0000 Aux Off (NOTE: If PV voltage registers “000V” when the breaker is kWHrs 00.0 Sleeping on, please check the polarity of the PV wires.) After 5 seconds of stable input voltage, the MX60 enters PV 087 V Bat 12.5 V a “Wakeup” stage, transitions to “Sweeping” and prepares 05.0 A 32.9 A Watts 0412 Aux Off to charge the
ページ20に含まれる内容の要旨
ACCESSING THE MAIN MENU The MAIN Menu allows the user to adjust and calibrate the MX60 for maximum performance. From the STATUS screen, press soft key #1 to open the MAIN Menu screen. Press the soft key after aligning the asterisk *Charger Aux Light in front of the selected menu choice. EQ Misc Advanced Logging Log2 Pressing the soft key in the MAIN Menu EXIT GO returns to the STATUS Menu. Press the soft key in your chosen menu to return to the STATUS
ページ1に含まれる内容の要旨
MX60 PV MPPT
(Maximum Power Point Tracking)
Charge Controller
Installation, Programming and User’s Manual
ページ2に含まれる内容の要旨
Warranty Summary Dear OutBack Customer, Thank you for your purchase of OutBack products. We make every eff ort to assure our power conversion products will give you long and reliable service for your renewable energy system. As with any manufactured device, repairs might be needed due to damage, inappropriate use, or unintentional defect. Please note the following guidelines regarding warranty service of OutBack products: • Any and all warranty repairs must conform to the terms of the warranty
