ページ1に含まれる内容の要旨
Public Signage
Solutions
EN User Manual
TYPE NR. BDL5231V
ページ2に含まれる内容の要旨
TABLE OF CONTENTS SAFETY INSTRUCTIONS .............................................................................................................................................................. 1 Contents .................................................................................................................................................................................... 7 Connection & Button Overviews ......................................................................
ページ3に含まれる内容の要旨
ページ4に含まれる内容の要旨
User Manual BDL5231V/00 SAFETY INSTRUCTIONS WARNINGS AND PRECAUTIONS KNOW THESE SAFETY SYMBOLS CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates high voltage is present inside. It is dangerous to make any kind of contact with any inside part of this product. This symbol alerts you that important literature concer
ページ5に含まれる内容の要旨
User Manual BDL5231V/00 REGULATORY INFORMATION CE DECLARATION OF CONFORMITY Philips Consumer Electronics declare under our responsibility that the product is in conformity with the following standards • EN60950-1:2001 (Safety requirement of Information Technology Equipment) • EN55022:2006 (Radio Disturbance requirement of Information Technology Equipment) • EN55024:1998+A1:2001+A2:2003 (Immunity requirement of Information Technology Equipment) •EN6100-3-2:2000+A2:2006 (Limits for Ha
ページ6に含まれる内容の要旨
User Manual BDL5231V/00 POLISH CENTER FOR TESTING AND CERTIFICATION NOTICE The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All equipment that works together (computer, monitor, printer, and so on) should have the same power supply source. The phasing conductor of the room’s electrical installation should have a reserve short-circuit protection device in the form of a fuse with a nominal value no larger than 1
ページ7に含まれる内容の要旨
User Manual BDL5231V/00 INFORMATION FOR UK ONLY WARNING - THIS APPLIANCE MUST BE EARTHED. Important: This apparatus is supplied with an approved moulded 13A plug. To change a fuse in this type of plug proceed as follows: 1. Remove fuse cover and fuse. 2. Fit new fuse which should be a BS 1362 5A,A.S.T.A. or BSI approved type. 3. Refit the fuse cover. If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate 3-pin plug fitted in its
ページ8に含まれる内容の要旨
User Manual BDL5231V/00 中国电子信息产品污染控制标识要求 (中国RoHS法规标示要求) 产品中有毒有害物质或元素的名称及含量 有毒有害物质或元素 部件名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 （Pb） （Hg）（Cd）（Cr 6+）（PBB） （PBDE） 外壳 ○ ○ ○ ○ ○ ○ × × ○ ○ ○ ○ 液晶面板 × ○ ○ ○ ○ ○ 电路板组件 附件 × ○ ○ ○ ○ ○ (遥控器，电源线，连接线) × 遥控器电池 ○ ○ ○ ○ ○ ○：表示该有毒有害物质在该部件所有均质材料中的含量均在SJ/T11363-2006 标准规定的限量要求以下 ◦ ×：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11363-2006 标准规定的限量要求 ◦ 环保使用期限 此标识指期限(十年)，电子信息产品中含有的有毒有害物质或元素在正常使用的条件下不会发生外 泄或突变，电子信
ページ9に含まれる内容の要旨
User Manual BDL5231V/00 NORTH EUROPE (NORDIC COUNTRIES) INFORMATION Placering/Ventilation VARNING: FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR DU STÄLLER DIN UTRUSTNING PÅPLATS. Placering/Ventilation ADVARSEL: SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT ER NEMT TILGÆNGELIGE. Paikka/Ilmankierto VAROITUS: SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI IRROTTAA PISTORASIASTA. Plassering/Ventilasjon ADVARSEL: NÅ
ページ10に含まれる内容の要旨
User Manual BDL5231V/00 Contents The BDL5231V monitor pack* should include: • Main switch cover • LCD monitor • Screw for Main Switch cover x 2 • Power cord (1.8 m) • BNC TO RCA adapter x 5 • VGA Signal Cable (1.8 m) • Logo guider • User Manual • Clamper • Remote Control and AAA Batteries • Screw for Clamper x 2 • Cable belt x 3 (For tightening cables) Xxxxxxxxxxxxxx xxxxxxxxxxxxxx xxxxxxxxxxxxxx xxxxx
ページ11に含まれる内容の要旨
User Manual BDL5231V/00 Connection & Button Overviews Control Panel POWER button ( ) : To switch the power on/off. MUTE button : To switch the audio mute ON/OFF. INPUT button : To set the function while OSD menu is on or to activate input selection menu while OSD menu is off. PLUS (+) button : To increase the adjustment while OSD menu is on, or to increase the audio output level while the OSD menu is off. MINUS (-) button : To decrease the adjustment while OSD menu is on, or t
ページ12に含まれる内容の要旨
User Manual BDL5231V/00 Terminal Panel EXTERNAL CONTROL (mini D-Sub 9 pin) This is for serial connection when multiple BDL5231V monitors are connected. To achieve remote management through RS232 commands (refer to the RS232 remote control user manual), connect the RS-232C OUT connector from a computer or from a different BDL5231V monitor to the RS-232C IN connector from your BDL5231V monitor. The same RS-2
ページ13に含まれる内容の要旨
User Manual BDL5231V/00 Remote Control SET button To activate the setting with OSD menu. AUTO ADJUST button To execute the AUTO ADJUST function. MUTE button To turn the mute function on/off. VIDEO SOURCE button To activate input selection menu, and push “ ” or “ ” to select input source from [HDMI], [DVI-D], [PC-A], [CVI], [VIDEO(S)] and [AV], and then push “SET” to switch to selected input source. AUDIO SOURCE button To acti
ページ14に含まれる内容の要旨
User Manual BDL5231V/00 Operating Range for the Remote Handling the remote control Control * Do not subject to strong shock. * Do not allow water or other liquid to splash the remote control. Point the top of the remote control toward the LCD monitor's remote If the remote control gets wet, wipe it dry immediately. sensor during button operation. * Avoid exposure to heat and steam. Use the remote control within a distance of about 7 m/ 23 ft from the * Other than to
ページ15に含まれる内容の要旨
User Manual BDL5231V/00 How to Mount or Attach Feet to the LCD Monitor You can install the LCD monitor in one of the following two ways: Way 1: Attach and remove the optional stands How to install stands 1. Please turn the monitor off. 2. After inserting stand in guide block, fasten the thumbscrews on both sides of the monitor. NOTE: Install the stands with their longer portions directing to the front. In the upright position How to remove the stands 1. Spre
ページ16に含まれる内容の要旨
User Manual BDL5231V/00 To avoid monitor from falling Take measures to prevent the monitor from falling over in case of an earthquake or other disaster might occur to lessen the probability of injury and damage. As shown in the figure below, secure the monitor to a solid wall or pillar using rope (commercially available) strong enough to bear the weight of the monitor(BDL5231V: approx. 47.5 kg). Screw hooks (commercially available), of ring type rather than C-shaped scr
ページ17に含まれる内容の要旨
User Manual BDL5231V/00 Ventilation Requirements for enclosure locating To allow heat to disperse, leave space between surrounding objects as shown in the diagram below. 14
ページ18に含まれる内容の要旨
User Manual BDL5231V/00 Setup Procedure 3. Connect to external equipment 1. Install the system on the right location • To protect the connected equipment, turn off the main power CAUTION: before making connections. THE LCD MONITOR MUST BE MOVED OR INSTALLED BY • Please refer to section “Connectivity” P.18~P.22 for operations.. TWO OR MORE PERSONS. Failure to follow this caution may result in injury and damage when the LCD monitor falls. 4. Connect powe
ページ19に含まれる内容の要旨
User Manual BDL5231V/00 9. Adjust the image Make adjustments to brightness or contrast if required. 10. Recommended Adjustment To reduce the risk of “image persistence”, please adjust the following items based on the application being used. “POWER SAVE”, “PANEL SAVING”, “DATE AND TIME”. 11. To prevent the main power switch from being changed To prevent the possibility of main power switch being carelessly pushed, please attach the main switch cover (accessory) onto it. NOTE:
ページ20に含まれる内容の要旨
User Manual BDL5231V/00 Install the LCD Monitor in Portrait Mode BDL5231V can be installed in portrait position, under the following conditions: Caution: Portrait mode is effective only when wall-mounted or ceiling-mounted. The feet can not be used for the monitor in portrait position. Placing the monitor in portrait position, will shorten the average life of the LCD backlight. Operational Environment (Temperature) shall be limited, as shown below: Operational
