ページ1に含まれる内容の要旨
Philips
Business
Solutions
E
E User Manual
G Benützersanleitung
I Guida Utente
S
Manual de uso
F
Manuel de l’utilisateur
TYPE NR. BDH5011
ページ2に含まれる内容の要旨
User Manual BDH5011 TABLE OF CONTENTS 1. Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 2. FCC Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 3. Cleaning and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 4. Product Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ページ3に含まれる内容の要旨
User Manual BDH5011 1. IMPORTANT SAFETY INSTRUCTIONS WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrow-head symbol within a triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product enclosure that may be of sufficient magnitude to constitute a risk of electric shocks to persons. WARNING To reduce the risk of electric shock, do not remove the front or back covers. No user-serviceable parts inside. Refer servicing to qualifie
ページ4に含まれる内容の要旨
User Manual BDH5011 • Do not place the unit on a bed, sofa, rug, or other similar surface. Never place the unit near or over a radiator or heat source. • Do not install unit in an enclosed area unless proper ventilation is provided. • The unit should be operated from the type of power source indicated on the label. If the type of available power is unknown, consult your dealer or local power company. • The unit is equipped with a 3-pin grounded plug.The plug will only fit into a grounded power o
ページ5に含まれる内容の要旨
User Manual BDH5011 2. FCC STATEMENT FCC Compliance Statement The equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in strict accordance with the instruction manual, may caus
ページ6に含まれる内容の要旨
User Manual BDH5011 3. CLEANING AND MAINTENANCE Cautions When Using the Plasma Display • Do not bring your hands, face or objects close to the ventilation holes of the plasma display.Top of plasma display is usually very hot due to the high temperature of exhaust air being released through the ventilation holes. Burns or personal injuries may occur if any body parts are brought too close. Placing any object near the top of the display could also result in heat related damages to the object as w
ページ7に含まれる内容の要旨
User Manual BDH5011 • Do not use volatile substances such as insect sprays, solvents and thinners on the cabinet. • Do not place anything made from rubber or PVC near the cabinet for extended periods of time. Avoid Still Images • Do not allow a still picture to be displayed for extended periods of time.This can cause a permanent image to remain on the plasma display. Examples of still images may include: still computer images, still video game images, still logos or pictures, text and images dis
ページ8に含まれる内容の要旨
User Manual BDH5011 4. PRODUCT FEATURES • Advanced Digital Image Processing Advanced digital processor with adaptive motion de-interlacing converts all 15KHz signals into progressive scan for a brighter, flicker free image. • Pull-Down for Film Scan Conversion Built-in 3:2 pull-down processing can automatically detect and convert film content to properly display with minimal motion artifacts. • 3D Comb Filter Built-in 3D comb filter converts analog signal into a digital signal for more accurate
ページ9に含まれる内容の要旨
User Manual BDH5011 • DVI Digital Video Interface with HDCP (High-Bandwidth Digital Content Protection Protocol) Standard DVI interface supports the lastest in digital video peripherals equipped with DVI HDCP digital video output(s).This means that digital content can now be passed from sources such as a digital DVD player, directly to this display without digital-to-analog conversion that causes loss of video quality. Direct digital-to-digital connection ensures the absolute best in video quali
ページ10に含まれる内容の要旨
User Manual BDH5011 5. PACKAGE CONTENTS Supplied Accessories Please verify that you received the following items with your package content: Plasma Display Remote Control User Manual Power Cable 10
ページ11に含まれる内容の要旨
User Manual BDH5011 VGA Cable Batteries Optional Accessories The following accessories are available and may be purchased from your local sales representative: • Wall Mount • Composite Video Cable (RCA) • S-Video Cable (Mini-Din) • Component Video Cable (RCA to RCA) • Audio Cable (RCA Cable) 11
ページ12に含まれる内容の要旨
User Manual BDH5011 6. UNDERSTANDING YOUR DISPLAY 6.1 Front View Power (Standby) Button Turns power on/off from standby mode. There is a 3-second wait between on/off cycles. Status LED: • Not Illuminated - No AC Power detected If the main power switch (rear of panel) is turned off, this LED will not illuminate. • Solid Yellow - Standby (Power OFF) with AC power detected The LED will illuminate in yellow color if the display is shut-off but the main power cord is plugged into the back of the unit
ページ13に含まれる内容の要旨
User Manual BDH5011 6.3 Remote Control 1. Standby Power On/Off Push this button to switch on the display from Standby mode. Push it again to switch 1 14 off to Standby mode. 2 15 2. Number Keypad These buttons are not applicable for this 16 display. 3 17 3. QuickView 4 This button is not applicable for this display. 18 5 4. PIP/POP Source 19 Changes the input source of the PIP or POP 6 sub-window. (See Chapter 10.1) 20 5. PIP (Picture-in-Picture Button) 7 21 Turns on PIP (Picture-in-Picture) mod
ページ14に含まれる内容の要旨
User Manual BDH5011 16. Channel Up/Down These buttons are not applicable to this display. 1 14 17. Swap 2 15 This button swaps the main and sub picture windows under PIP or POP modes. 16 (See chapter 10.) 3 18. PIP Position 17 4 This button changes the PIP sub-window to 18 4 different corner locations. 5 (See Chapter 10.) 19 6 19. Input Select 20 Press to select input signal modes sequentially. (See Chapter 8.2.) 7 21 20. MENU Adjustment 8 1. Show OSD menu by pressing or 22 button or MENU button
ページ15に含まれる内容の要旨
User Manual BDH5011 7. CONNECTING THE DISPLAY 7.1 Connecting a DVD Player Using Component Video Input 1. Connect the green-colored (labeled as Y) jack from the DVD to the green-colored Y1-jack of the display. 2. Connect the red-colored (labeled as PR or CR) jack from the DVD to the red-colored PR1/CR1 jack of the display. 3. Connect the blue-colored (labeled as PB or CB) jack from the DVD to the blue-colored PB1/CB1 jack of the display. 4. Connect the red (R) and white (L) audio jacks from the
ページ16に含まれる内容の要旨
User Manual BDH5011 7.2 Connecting a HDTV Decoder Set-Top Box Using Component Video Input 1. Connect the green (labeled as Y) jack from the HDTV Set-top box to the green Y1 jack of the display. 2. Connect the red (labeled as PR or CR) jack from the HDTV Set-top box to the red PR1/CR1 jack of the display. 3. Connect the blue (labeled as PB or CB) jack from the HDTV Set-top box to the blue PB1/CB jack of the display. 4. Connect the red (R) and white (L) audio jacks from the HDTV Set-top box to the
ページ17に含まれる内容の要旨
User Manual BDH5011 7.4 External Audio Connections Connecting External Amplified Speakers 1. This display can be connected to an external set of amplified speakers using the AUDIO OUT jacks located on the back of the display. In addition, this display is equipped with a small 3.5 mm phono style plug for remote turn-on applications that will auto- matically send a remote turn-on/off signal to the external amplified speakers. 2. Connect the red (R) and white (L) AUDIO OUT jacks at the right hand s
ページ18に含まれる内容の要旨
User Manual BDH5011 7.5 Connecting a PC Using RGB or DVI Video Input 1. For most PC’s, connect the 15-pin D-Sub RGB connector from the back of the PC to the RGB-IN connector located on the back of the display. If you have a PC that is equipped with a DVI (Digital Visual Interface), you may connect the PC DVI connector from the back of the PC to the DVI-In connector located on the back of the display. 2. Connect the red (R) and white (L) audio jacks from the PC to the R and L jacks located to the
ページ19に含まれる内容の要旨
User Manual BDH5011 7.6 RS-232 Remote Control Connections RS-232 Serial Terminal Overview This display is equipped with an RS-232 serial terminal for using the display with computer controls.The RS-232 serial terminal conforms to the RS-232C interface specification.The computer will require a software application (such as programming language software) which allows the computer to send and receive control data that can support the communications parameters listed below. Communications Parameters
ページ20に含まれる内容の要旨
User Manual BDH5011 Notes: • To connect a PC to the display’s RS-232 port, you must use a straight-through RS-232 cable where pins 2 (RX) and 3 (TX) are not reversed at one end. • If there is no data to be sent, then it is not necessary to send the parameter signal. • If multiple commands are transmitted, make sure to wait for the response for the first command to come from the display before sending the next command. Normally the sent data byte will be returned as an answer. In case of an error
