ページ1に含まれる内容の要旨
PLASMA DISPLAY
ELECT
Owner’s Instructions
Before operating the unit,
please read this manual thoroughly,
and retain it for future reference.
REMOTE CONTROL
ON-SCREEN MENUS
PICTURE IN PICTURE
TELETEXT
ENG
ページ2に含まれる内容の要旨
Safety Instructions ENG Do not place the PDP on an unstable cart, stand, tripod, bracket, table, or floor where it can fall. Do not expose the PDP to extreme temperature conditions or to extreme humidity conditions. Do not expose the PDP to direct sunlight and other sources of heat. Do not expose the PDP to any liquids. Never put objects of any kind into the television, and do not place a water-containing vessel on the PDP. During a storm conditions (especially when there is lightnin
ページ3に含まれる内容の要旨
Caution ENG CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN ! CAUTION: TO PREVENT ELECTRICAL SHOCK, DO NOT REMOVE REAR COVER, NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash and arrow head The main voltage is indicated on the ☛ within the triangle is a warning sign rear of the PDP and the frequency is alerting you of “dangerous voltage” 50 or 60Hz. inside the product. The exclamation point within the WARNING: TO PREVENT DAMAGE WHICH MAY triangle i
ページ4に含まれる内容の要旨
ENG Contents (continued) FOREWORD Safety Instructions .................................................................................................... 2 User Instructions....................................................................................................... 2 Caution ..................................................................................................................... 3 Checking Parts ...................................................................
ページ5に含まれる内容の要旨
ENG Contents CONNECTING AND OPERATING A PC Connecting a PC....................................................................................................... 33 Setting up Your Display Plug and Play ..................................................................... 34 Setting up Your PC Software (Windows only) .......................................................... 34 PC Input Mode................................................................................................
ページ6に含まれる内容の要旨
Your New Plasma Display Panel ENG Front Panel SPEAKER SPEAKER POWER Remote Control Signal Receiver Press to turn the Aim the remote control towards this spot on PDP on and off. the PDP. SOURCE External input selection. MENU Menu display. - VOLUME + Volume adjustment. SELECT Control the cursor in the Menu. MUTE Temporary sound switch-off. 6
ページ7に含まれる内容の要旨
Your New Plasma Display Panel The actual configuration on your PDP may be different, ➢ ENG depending on your model. Rear Panel a) External Speaker Outputs (8Ω ) e) SCART Input Connect external speakers. Connect a audio, video, or RGB signal from external sources like VCRs or DVD players. b) S-VIDEO Input (Signal Output does not operate). Connect a S-Video signal from an S-VHS VCRs or DVD players. f) Audio Inputs (Video/PC) Connect a audio signal from external sources c) VIDEO Input like VCRs or
ページ8に含まれる内容の要旨
Remote Control Buttons Some remote control buttons do not operate with the PDP. ➢ ENG AUTOMATIC SWITCH-OFF VCR/DVD FUNCTIONS; - STOP - REWIND - PLAY/PAUSE/ - FAST-FORWARD PIP FUNCTIONS; - PIP ON/OFF - INTERCHANGE THE MAIN AND THE SUB PICTURE (SWAP) Power - LOCATION SELECTION (LOCATE) - SIZE SELECTION (SIZE) - INPUT SOURCE SELECTION (SOURCE) POWER ON/OFF MAKE THE REMOTE CONTROL WORKS NUMERIC BUTTONS FOR MONITOR, VCR, CABLE, DVD PLAYER EXTERNAL INPUT SELECTION SELECT TO THE PC MODE DIRECTLY TEMPO
ページ9に含まれる内容の要旨
Inserting the Batteries in the Remote Control ENG You must insert or replace the batteries in the remote control when you: Purchase the PDP Find that the remote control is no longer operating correctly 1 Remove the cover on the rear of the remote control by pressing the symbol downwards and then pulling firmly to remove it. 2 Insert two R03, UM4, “AAA” 1.5V or equivalent batteries taking care to respect the polarities: + on the battery against + on the remote control - on the battery aga
ページ10に含まれる内容の要旨
Installing the Display on the Wall Attachment Panel Wall attachment panel is sold separately. Check with your dealer ➢ ENG 1 Check for the stability of the wall where the PDP is to be installed. If the wall is not enough strong to support the PDP, strengthen the wall before installation. 2 Fix the wall attachment panel on the wall using bolts as shown in the figure: Fixing bolts must protrude from the wall appox. 1.5cm. 3 Using the wall attachment panel, you may adjust the angle of the display f
ページ11に含まれる内容の要旨
Installing the Display on the Wall Attachment Panel ENG 4 Remove four large screws from the rear side of the display. Insert the bolts, dish-type washers, and insulation rubber into the four screw-holes as shown in the figure: Bolt Insulation rubber 5 Put the insulation rubber point protruding from the rear top of the display in the groove on the top of the wall attachment panel. Lift up the display a little bit so that the insulation rubber point at the bottom Πof the rear side of the displa
ページ12に含まれる内容の要旨
Separating the Display from the Wall Attachment Panel ENG Remove the fixing bolts from both sides (left and right) of the wall attachment panel. Lift and pull the bottom of the display a small amount, to separate the insulation rubber point from the bottom of the wall attachment panel. Lift the display and separate the insulation rubber point from the groove on top of the wall attachment panel. Œ ´ 12
ページ13に含まれる内容の要旨
Before Connecting the Display to External Equipment ENG Carefully check the connectors for position and type before making any connections. Loose connectors can result in picture or color problems. Make sure that all connectors are securely inserted into their terminals. Ferrite Cores The ferrite cores are used to attenuate undesired signals. When connecting cables, attach one of these ferrite cores to the cable near the connector. 50” only When you connect the speaker wire to the ➢ External Spe
ページ14に含まれる内容の要旨
Connecting Speakers ENG Connect the speaker audio cable to the external speaker output jack on the rear of the PDP matching the “+” and “-” ends of the cable with the diagram on the PDP. The speakers MUST have more than 7watts rating (impedance 8Ω ). ➢ Connecting PDP and Speakers Fix the bracket onto the guide pole located on the rear of speaker Guide pole and fasten the screws. After removing the three screws on the PDP, clamp the speaker and the PDP together and fasten the screws. Guide pole W
ページ15に含まれる内容の要旨
Connecting Your VCR or Cable Box ENG Connect a Video/S-Video cable between the Rear panel Video/S-Video output jack on the VCR/Cable box and the Video input jack on the PDP. - For better video, you can use a S-Video cable. Connect an Audio cable between the Audio output jack on the VCR/Cable box and the Audio input jack on the PDP. Videotape Playback 1 Turn on PDP and select the Video or S-Video mode (if S-Video jack is connected) by pressing the Source on the remote control. 2 Turn on your
ページ16に含まれる内容の要旨
Switching On and Off ENG The mains lead is attached to the rear of the PDP. Front panel If you have purchased this PDP in the United Kingdom, ☛ refer to page 55 for further instructions on plug wiring. 1 Plug the mains lead into an appropriate socket. The main voltage is indicated on the rear of the display and ➢ the frequency is 50 or 60Hz. 2 Press the POWER ( ) button on the front panel or remote control to switch the display on. If your Monitor isn’t turned on when the power button is ➣ press
ページ17に含まれる内容の要旨
Choosing Your Language ENG When you start using your PDP for the first time, you must select the S E T U P language which will be used for displaying menus and indications. Color System Auto Digital NR Off 1 Press the Menu button. Auto Power On On Panel Lock Off Result: The main menu is displayed. Miscellaneous 2 Move the joystick up or down to select the SETUP menu and press Move Enter Exit the joystick button. 3 Move the joystick up or down to select the Miscellaneous me
ページ18に含まれる内容の要旨
Using the Various Setup Menus ENG Color System S E T U P You can use your PDP in many countries. Each country ˆ ¤ Color System Auto has its own broadcasting standard. Depending on your Digital NR Off country, the color systems are displayed in the order Auto Power On On given. Panel Lock Off If an abnormal phenomenon appears on the screen ➣ Miscellaneous when Auto is selected, then select the color system manually. Move Select Exit Digital NR If the broadcast signal rec
ページ19に含まれる内容の要旨
Using Automatic Picture Settings ENG You can select the picture effect which best corresponds to your P I C T U R E viewing requirements. The following picture effects are available in Select ˆ Custom ¤ the order given: Contrast Custom, Standard, Sports, Movie, Mild, Dynamic. Brightness Sharpness Color In the PC mode, you can select Custom, High, Middle or Low. ➣ Color Tone Normal Move Select Exit 1 Press the Menu button, then press the joystick b
ページ20に含まれる内容の要旨
Customizing the Picture ENG Your PDP has several settings which allow you to control picture P I C T U R E quality: Select Custom Contrast, Brightness, Sharpness, Color, Contrast Color Tone, Tint (NTSC only). Brightness Sharpness Color When the Select is set to Custom, the following settings can ➣ Color Tone Normal be adjusted. Move Adjust Exit 1 Press the Menu button, then press the joystick button to enter the PICTURE menu. Contrast
