ページ1に含まれる内容の要旨
BN68-00679A-00 ENG 4/19/04 2:56 PM Page 1
PDP-TELEVISION
(PLASMA DISPLAY PANEL)
Owner’s Instructions
Before operating the unit,
please read this manual thoroughly,
and retain it for future reference.
ON-SCREEN MENUS
PICTURE IN PICTURE (PIP)
TELETEXT / TELEWEB (OPTION)
ページ2に含まれる内容の要旨
BN68-00679A-00 ENG 4/19/04 2:56 PM Page 2 User Instructions ENG ◆ Screen Image retention Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the plasma monitor panel for more than 2 hours as it can cause screen image retention. This image retention is also known as “screen burn”. To avoid such image retention, reduce the degree of brightness and contrast of this screen when displaying a still image. ◆ Cell Defect The plasma display panel consists of f
ページ3に含まれる内容の要旨
BN68-00679A-00 ENG 4/19/04 2:56 PM Page 3 Checking Parts ENG Sold Separately DVI Cable S-VIDEO Cable Owner’s Instructions Remote Control/ AAA Batteries Component Cables PC Cable (RCA) Ferrite Core for Antenna Cable Side AV Cable Scart Cable Speaker Wire PC Audio Cable Power Cord Ferrite Core (depending on the model) The ferrite core is used to attenuate undesired signals. When connecting cable, attach this ferrite core to the cable near the connector. When you connect Side AV cable to the AV
ページ4に含まれる内容の要旨
BN68-00679A-00 ENG 4/19/04 2:56 PM Page 4 ENG Contents ◆ FOREWORD ■ User Instructions............................................................................................ 2 ◆ CONNECTING AND PREPARING YOUR DISPLAY ■ Your New Plasma Display Panel................................................................... 6 ■ Infrared Remote Control................................................................................ 8 ■ Inserting the Batteries in the Remote Control.....................
ページ5に含まれる内容の要旨
BN68-00679A-00 ENG 4/19/04 2:56 PM Page 5 ENG Contents (continued) ◆ USING YOUR DISPLAY ■ Adjusting the Sound Settings ........................................................................ 40 ■ Adjusting the Volume Automatically .............................................................. 40 ■ Setting the TruSurround XT........................................................................... 41 ■ Selecting the Internal mute...............................................................
ページ6に含まれる内容の要旨
BN68-00679A-01 ENG 4/19/04 5:05 PM Page 6 Your New Plasma Display Panel The actual configuration on your PDP may be different, ➢ ENG depending on your model. Front Panel Touch button Touch the right side of each button name using your finger to operate the button. a) SOURCE f) I / External input selection. Press to turn the PDP on and off. Power Indicator b) MENU - Power Off: Red Menu display. - Power On: Off - Timer On: Green c) - + Volume adjustment. g) Remote Control Signal Receiver Also
ページ7に含まれる内容の要旨
BN68-00679A-00 ENG 4/19/04 2:56 PM Page 7 Your New Plasma Display Panel (continued) The actual configuration on your PDP may be different, ➢ ENG depending on your model. Side of the TV S-Video Input Video Input Audio Input (L, R) Rear Panel For further details about connection, refer to pages 55~59. ➢ a) DVI INPUT (DVI-D / L-AUDIO-R) g) AV1, AV2, AV3 Connect to the digital video and audio output jack (VIDEO / L-AUDIO-R ) for device with DVI output. Video and audio inputs for external devic
ページ8に含まれる内容の要旨
BN68-00679A-00 ENG 4/19/04 2:56 PM Page 8 Infrared Remote Control ENG TURNS THE PDP ON AND OFF WHEN YOU PRESS A BUTTON , ‘ ’ APPEARS ALONG WITH SELECTED MODE (TV, VCR, CATV, DVD OR STB) AND BATTERY STATUS ON LCD PICTURE EFFECT SELECTION MAKE THE REMOTE CONTROL WORKS SOUND EFFECT SELECTION FOR TV, VCR, CATV, DVD PLAYER, STB TELETEXT CANCEL DIRECT CHANNEL SELECTION AUTOMATIC SWITCH-OFF/ TELETEXT SUB-PAGE PICTURE SIZE/ TELETEXT SIZE SELECTION NEXT CHANNEL/ TELETEXT NEXT PAGE/ VOLUME INCREASE TE
ページ9に含まれる内容の要旨
BN68-00679A-00 ENG 4/19/04 2:56 PM Page 9 Inserting the Batteries in the Remote Control ENG You must insert or replace the batteries in the remote control when you: ◆ Purchase the PDP ◆ Find that the remote control is no longer operating correctly 1 Remove the cover on the rear of the remote control by pressing the symbol ( ) downwards and then pulling firmly to remove it. 2 Insert two R03, UM4, “AAA” 1.5V or equivalent batteries taking care to respect the polarities: ◆ - on the battery again
ページ10に含まれる内容の要旨
BN68-00679A-00 ENG 4/19/04 2:56 PM Page 10 Installing the Display on the Wall Attachment Panel ENG Installation Notes ◆ Do not install the PDP on any place other than vertical walls. ◆ To protect the performance of the PDP and prevent troubles, avoid the followings: - Do not install next to smoke and fire detectors. - Do not install in an area subjected to vibration or high voltage. - Do not install near or around any heating apparatus. ◆ Use only recommended parts and components. Mounting Ki
ページ11に含まれる内容の要旨
BN68-00679A-00 ENG 4/19/04 2:56 PM Page 11 Installing the Display on the Wall Attachment Panel (continued) The exterior of the PDP may be different than the picture. ➢ ENG (Assembly and installation of the plastic hanger is the same.) 1 Remove the screws from the back of the PDP. 2 Use the screws and assemble the plastic hanger. ◆ Please ask the installers to install the ☛ wall mount bracket. ◆ Please be sure to check if the plastic hanger is completely secured on both the left and right side
ページ12に含まれる内容の要旨
BN68-00679A-00 ENG 4/19/04 2:56 PM Page 12 Connecting to an Aerial or Cable Television Network ENG To view television channels correctly, a signal must be received by the set from one of the following sources: ◆ An outdoor aerial ◆ A cable television network ◆ A satellite network 1 In the first three cases, connect the aerial or network input cable to the 75Ω coaxial socket on the rear of the PDP. Rear of the PDP 2 If you are using an indoor aerial, you may need to turn it when tuning your PD
ページ13に含まれる内容の要旨
BN68-00679A-00 ENG 4/19/04 2:56 PM Page 13 Switching On and Off ENG The mains lead is attached to the rear of your PDP. If you have purchased this PDP in the United Kingdom, ☛ refer to page 64 for further instructions on plug wiring. Front of the PDP 1 Plug the mains lead into an appropriate socket. Result: The Standby indicator on the front of the PDP lights up. The main voltage is indicated on the rear of the PDP and ➢ the frequency is 50 or 60Hz. 2 Press the “ I / ” button on the front of
ページ14に含まれる内容の要旨
BN68-00679A-00 ENG 4/19/04 2:56 PM Page 14 Becoming Familiar with the Remote Control ENG The remote control is used mainly to: ◆ Change channels and adjust the volume ◆ Display the on-screen menu system The following table presents the most frequently used buttons and their functions. Button Viewing Function Menu Function Used to display the next - stored channel. Used to display the - previous stored channel. to Used to display the corresponding channels. For double digit channels, the secon
ページ15に含まれる内容の要旨
BN68-00679A-00 ENG 4/19/04 2:56 PM Page 15 Setting Up Your Remote Control ENG This PDP’s remote control can operate VCR, CATV , DVD, or Set-top box (STB), in addition to controlling the PDP. The remote control is not compatible with the TV ➢ manufactured by another company. VCR 1 Turn off your VCR, Cable box, DVD or STB. 2 Press the SELECT button. Mode is changed whenever SELECT button is pressed. 3 Press the POWER() button on the remote control. The component you select should turn on. If i
ページ16に含まれる内容の要旨
BN68-00679A-00 ENG 4/19/04 2:57 PM Page 16 Plug & Play Feature ENG When the television is initially powered ON, several basic customer Plug & Play settings proceed automatically and subsequently. The following settings are available. Press ENTER to Start Plug & Play Start 1 If the television is in Standby mode, press the POWER() button Enter Exit on the remote control. Language Result: The message Plug & Play is displayed, and then the Language menu is automatically displayed a few sec
ページ17に含まれる内容の要旨
BN68-00679A-00 ENG 4/19/04 2:57 PM Page 17 Plug & Play Feature (continued) ENG If you want to reset this feature... TV Setup 1 Press the MENU button. √ √ Time Result: The main menu is displayed. Language : English √ √ √ √ AV Setup 2 Press the † or … button to select Setup. Digital NR : On √ √ √ √ Miscellaneous Result: The options available in the Setup group are displayed. PC Setup √ √ 3 Press the ENTER() button. Move Enter Return 4 Press the † or … button to select Miscellaneous. Press the E
ページ18に含まれる内容の要旨
BN68-00679A-00 ENG 4/19/04 2:57 PM Page 18 Storing Channels Automatically ENG You can scan for the frequency ranges available to you, (availability depends on your country). Automatically allocated programme TV Channel numbers may not correspond to actual or desired programme √ √ Country : Austria numbers. However you can sort numbers manually and clear any Auto Store √ √ channels you do not wish to watch. √ √ Manual Store Edit √ √ √ √ Fine Tune 1 Press the MENU button. Ch. Scan √ √ Result: T
ページ19に含まれる内容の要旨
BN68-00679A-00 ENG 4/19/04 2:57 PM Page 19 Storing Channels Manually ENG You can store up to 100 television channels, including those received via cable networks. TV Channel √ √ Country : Austria When storing channels manually, you can choose: Auto Store √ √ √ √ Manual Store ◆ Whether or not to store each of the channels found Edit √ √ √ √ ◆ The programme number of each stored channel which Fine Tune Ch. Scan √ √ you wish to identify Move Enter Return 1 Press the MENU button. Result: The main
ページ20に含まれる内容の要旨
BN68-00679A-00 ENG 4/19/04 2:57 PM Page 20 Storing Channels Manually (continued) ENG 8 If you know the number of the channel to be stored, see the Manual Store following steps. Prog. Colour Sound System System ◆ Press the œ or √ button to select Channel. 9 Auto BG ◆ Press the † or … button to select C (Air channel) or S (Cable Channel Search Store channel). -- C 245MHz ? ◆ Press the √ button. œ œ √ √ Move Adjust Return ◆ Press the numeric buttons (0~9), † or … button to select indicate t
