Chamberlain 2220 1/2 HPの取扱説明書

デバイスChamberlain 2220 1/2 HPの取扱説明書

デバイス: Chamberlain 2220 1/2 HP
カテゴリ: ガレージドア自動開閉装置
メーカー: Chamberlain
サイズ: 1.49 MB
追加した日付: 11/10/2013
ページ数: 36
説明書を印刷

ダウンロード

使い方は?

私たちの目的は、皆様方にデバイスChamberlain 2220 1/2 HPの取扱説明書に含まれたコンテンツを可能な限り早く提供することです。オンラインプレビューを使用すると、Chamberlain 2220 1/2 HPに関してあなたが抱えている問題に対する解決策の内容が素早く表示されます。

便宜上

説明書Chamberlain 2220 1/2 HPをこちらのサイトで閲覧するのに不都合がある場合は、2つの解決策があります:

  • フルスクリーン表示 – 説明書を(お使いのコンピュータにダウンロードすることなく)便利に表示させるには、フルスクリーン表示モードをご使用ください。説明書Chamberlain 2220 1/2 HPのフルスクリーン表示を起動するには、全画面表示ボタンを押してください。
  • コンピュータにダウンロード - Chamberlain 2220 1/2 HPの説明書をお使いのコンピュータにダウンロードし、ご自身のコレクションに加えることもできます。デバイス上のスペースを無駄にしたくない場合は、いつでもManualsBaseサイトでダウンロードすることもできます。
Chamberlain 2220 1/2 HP 取扱説明書 - Online PDF
Advertisement
« Page 1 of 36 »
Advertisement
印刷版

多くの人々は画面表示ではなく印刷された説明書を読むほうを好みます。説明書を印刷するオプションも提供されており、上記のリンクをクリックすることによりそれを利用できます - 説明書を印刷。説明書Chamberlain 2220 1/2 HPを全部印刷する必要はなく、選択したページだけを印刷できます。紙を節約しましょう。

要旨

次のページにある説明書Chamberlain 2220 1/2 HPの内容のプレビューは、以下にあります。次のページにある説明書の内容をすぐに表示したい場合は、こちらをご利用ください。

内容要旨
ページ1に含まれる内容の要旨

The Chamberlain Group, Inc.
845 Larch Avenue
Elmhurst, Illinois 60126-1196
www.liftmaster.com
®
GARAGE DOOR OPENER
Model 2110 1/3 HP
2220 1/2 HP
2220-267 1/2 HP
For Residential Use Only
Owner’s Manual
 Please read this manual and the enclosed safety materials carefully!
 Fasten the manual near the garage door after installation.
®
 The door WILL NOT CLOSE unless the Protector System is connected and
properly aligned.
 Periodic checks of the opener are required to ensure safe operation.
 Th

ページ2に含まれる内容の要旨

TABLE OF CONTENTS Introduction Pages 2-5 Adjustment Pages 24-26 Safety symbol and signal word review........................2 Adjust the travel limits ...............................................24 Preparing your garage door ........................................3 Adjust the force .........................................................25 Tools needed...............................................................3 Test the safety reversal system.................................26 ® Plannin

ページ3に含まれる内容の要旨

1 Preparing your garage door WARNING WARNING Before you begin: To prevent possible SERIOUS INJURY OR DEATH: • Disable locks. • ALWAYS call a trained door systems technician if CAUTION WARNING • Remove any ropes connected to garage door. garage door binds, sticks, or is out of balance. An unbalanced garage door may not reverse when • Complete the following test to make sure your required. garage door is balanced and is not sticking or • NEVER try to loosen, move or adjust garage door, door bindi

ページ4に含まれる内容の要旨

— — — — — — — — Planning Identify the type and height of your garage door. Survey your garage area to see if any of the conditions below apply to your installation. Additional materials may be required. You may find it helpful to refer back to this page and the accompanying illustrations as you proceed with the installation of your opener. SECTIONAL DOOR INSTALLATION FINISHED CEILING Support bracket & fastening hardware is required. Horizontal and vertical reinforcement See page

ページ5に含まれる内容の要旨

Carton Inventory Your garage door opener is packaged in two cartons purchased. If anything is missing, carefully check the which contain the motor unit and all parts illustrated packing material. Parts may be stuck in the foam. below. Accessories will depend on the model Hardware for installation is also listed below. Models 2220, 2220-267 Model 2110 Models 2220 (1), 2220-267 (2) Model 2110 (1) Remote Control SECURITY✚ SECURITY✚ Transmitter Visor Clip Single-Function Remote Control 3-Channel R

ページ6に含まれる内容の要旨

ASSEMBLY STEP 1 HARDWARE SHOWN ACTUAL SIZE Fasten the Rail to the Motor Unit Hex Bolt Lock Nut 1/4" - 20 1/4" - 20 x 5/8" To avoid installation difficulties, do not run the garage door opener until instructed to do so. • Working on a level surface, align the rail assembly with the motor unit, as shown. • Slip the coupling over the rail sprocket. • Slide the rail through the motor unit bracket until the coupling fits securely over the motor unit Motor Unit sprocket. Sprocket Motor Unit • Align th

ページ7に含まれる内容の要旨

ASSEMBLY STEP 3 Lock Nuts Attach the Rail Brackets 1/4"-20 Rail Brackets • Align rail brackets to end of rail assembly, as shown. • Insert two 1/4"-20 x 5/8" hex bolts and lock nuts. Tighten securely with a 7/16" socket. You have now finished assembling your garage Hex door opener. Please read the following warnings Bolts Rail 1/4"-20x5/8 before proceeding to the installation section. HARDWARE SHOWN ACTUAL SIZE Hex Bolt Lock Nut 1/4" - 20 1/4" - 20 x 5/8" INSTALLATION IMPORTANT INSTALLATION IN

ページ8に含まれる内容の要旨

INSTALLATION STEP 1 Finished Determine the Header Bracket Vertical Ceiling Centerline Location Header Structural 2x4 Wall Supports WARNING WARNING To prevent possible SERIOUS INJURY or DEATH: • Header bracket MUST be RIGIDLY fastened to CAUTION WARNING structural support on header wall or ceiling, otherwise garage door might not reverse when required. DO NOT install header bracket over drywall. • Concrete anchors MUST be used if mounting header Vertical bracket or 2x4 into masonry. Centerline •

ページ9に含まれる内容の要旨

ONE-PIECE DOOR WITHOUT TRACK Unfinished Ceiling 1. Close the door and mark the inside vertical centerline of your garage door. Extend the line Structural onto the header wall above door, as shown. Supports Header Wall Vertical If headroom clearance is minimal, you can install Centerline 2x4 the header bracket on the ceiling. See page 10. 2x4 If you need to install the header bracket on a 2x4 (on wall or ceiling), use lag screws (not provided) OPTIONAL to securely fasten the 2x4 to structural sup

ページ10に含まれる内容の要旨

INSTALLATION STEP 2 Install the Header Bracket Wall Mounting Holes You can attach the header bracket either to the wall CEILING MOUNT ONLY above the garage door, or to the ceiling. Follow the The nail hole is for positioning only. instructions which will work best for your particular You must use lag screws UP requirements. Do not install the header bracket to mount the header bracket. over drywall. If installing into masonry, use concrete anchors (not provided). WALL HEADER BRACKET INSTALLAT

ページ11に含まれる内容の要旨

INSTALLATION STEP 3 Attach the Rail to the Header Bracket • Position the opener on the garage floor below the header bracket. Use packing material as a protective base. NOTE: If the door spring is in the way you’ll need help. Have someone hold the opener securely on a temporary support to allow the rail to clear the spring. • Position the rail bracket against the header bracket. Header Wall • Align the bracket holes and join with a clevis pin as shown. Header Bracket • Insert a ring fastener to

ページ12に含まれる内容の要旨

INSTALLATION STEP 4 WARNING WARNING ® Install The Protector System • Be sure power is not connected to the garage door opener BEFORE installing the safety reversing sensor. The safety reversing sensor must be connected CAUTION WARNING • To prevent SERIOUS INJURY or DEATH from a closing and aligned correctly before the garage door garage door: opener will move in the down direction. – Correctly connect and align the safety reversing IMPORTANT INFORMATION ABOUT sensor. This required safety device

ページ13に含まれる内容の要旨

INSTALLING THE BRACKETS Figure 1 Be sure power to the opener is disconnected. Install and align the brackets so the sensors will face DOOR TRACK MOUNT (RIGHT SIDE) each other across the garage door, with the beam no higher than 6" above the floor. They may be installed Door in one of three ways, as follows: Track Garage door track installation (preferred): Lip Indicator • Slip the curved arms over the rounded edge of light each door track, with the curved arms facing the door. Snap into place

ページ14に含まれる内容の要旨

MOUNTING AND WIRING THE SAFETY Figure 4 SENSORS Wing nut • Slide a 1/4"-20x1/2" carriage bolt head into the slot on each sensor. Use wing nuts to fasten sensors to brackets, with lenses pointing toward each other across the door. Be sure the lens is not Carriage bolt obstructed by a bracket extension (Figure 4). 1/4"-20x1/2" Lens • Finger tighten the wing nuts. Recommended Wire Routing HARDWARE SHOWN ACTUAL SIZE 1. Using insulated staples, run the wires from both sensors to the rail at the doo

ページ15に含まれる内容の要旨

WARNING WARNING INSTALLATION STEP 5 CAUTION WARNING Position the Opener To prevent damage to garage door, rest garage door opener rail on 2x4 placed on top section of door. Follow instructions which apply to your door type as illustrated. SECTIONAL DOOR OR ONE-PIECE DOOR WITH TRACK A 2x4 laid flat is convenient for setting an ideal door- to-rail distance. 2x4 • Raise the opener onto a stepladder. You will need Header laid flat Bracket help at this point if the ladder is not tall enough. • Open

ページ16に含まれる内容の要旨

INSTALLATION STEP 6 WARNING WARNING Hang the Opener To avoid possible SERIOUS INJURY from a falling garage door opener, fasten it SECURELY to structural Two representative installations are shown. Yours CAUTION WARNING supports of the garage. Concrete anchors MUST be used may be different. Hanging brackets should be angled if installing ANY brackets into masonry. (Figure 1) to provide rigid support. On finished ceilings (Figure 2), attach a sturdy metal bracket to structural supports before inst

ページ17に含まれる内容の要旨

LIGHT LIGHT WARNING WARNING INSTALLATION STEP 7 CAUTION WARNING Install the Door Control To prevent possible SERIOUS INJURY or DEATH from electrocution: Locate door control within sight of the door at a minimum • Be sure power is not connected BEFORE installing door height of 5 feet where small children cannot reach, and control. away from moving parts of the door and door hardware. The installation surface must be smooth and flat. If • Connect ONLY to 24 VOLT low voltage wires. installing into

ページ18に含まれる内容の要旨

NOTICE Top Lens Tab INSTALLATION STEP 8 Lens Install the Lights • Install up to a 100 watt maximum light bulb in each Bottom Lens Tab socket. The lights will turn ON and remain lit for Top approximately 4-1/2 minutes when power is Chassis Slot connected. Then the lights will turn OFF. • Insert bottom lens tabs into slots on chassis. Tilt towards chassis to engage top tabs, then drop down gently into place. Bottom • To remove, depress both top lens tabs. Tilt lens Chassis Slots slightly outward

ページ19に含まれる内容の要旨

INSTALLATION STEP 10 WARNING WARNING Electrical Requirements To prevent possible SERIOUS INJURY or DEATH from electrocution or fire: To avoid installation difficulties, do not run the CAUTION WARNING • Be sure power is not connected to the opener, and opener at this time. disconnect power to circuit BEFORE removing cover to To reduce the risk of electric shock, your garage door establish permanent wiring connection. opener has a grounding type plug with a third • Garage door installation and wir

ページ20に含まれる内容の要旨

WARNING WARNING CAUTION INSTALLATION STEP 12 WARNING Fasten the Door Bracket To prevent damage to garage door, reinforce inside of door with angle iron both vertically and horizontally. Follow instructions which apply to your door type as illustrated below or on the following page. A horizontal reinforcement brace should be long Header Bracket enough to be secured to two or three vertical supports. A vertical reinforcement brace should cover the height of the top panel. Figure 1 shows one piec


類似の説明書
# 取扱説明書 カテゴリ ダウンロード
1 Chamberlain 1000E - 1/4 HP 取扱説明書 ガレージドア自動開閉装置 188
2 Chamberlain 1000SDC 1/3HP 取扱説明書 ガレージドア自動開閉装置 30
3 Chamberlain 1140 取扱説明書 ガレージドア自動開閉装置 17
4 Chamberlain 1025 取扱説明書 ガレージドア自動開閉装置 18
5 Chamberlain 1000SDR 1/3 HP 取扱説明書 ガレージドア自動開閉装置 9
6 Chamberlain 1000SDC-R, 2000SDC-R 取扱説明書 ガレージドア自動開閉装置 3
7 Chamberlain 1022 取扱説明書 ガレージドア自動開閉装置 11
8 Chamberlain 1042 取扱説明書 ガレージドア自動開閉装置 2
9 Chamberlain 1146 取扱説明書 ガレージドア自動開閉装置 1
10 Chamberlain 1024 取扱説明書 ガレージドア自動開閉装置 3
11 Chamberlain 1145-1/3HP 取扱説明書 ガレージドア自動開閉装置 1
12 Chamberlain 1145 取扱説明書 ガレージドア自動開閉装置 2
13 Chamberlain 1145- 1/3HP 取扱説明書 ガレージドア自動開閉装置 1
14 Chamberlain 1145jg 取扱説明書 ガレージドア自動開閉装置 3
15 Chamberlain 1150 取扱説明書 ガレージドア自動開閉装置 4
16 Sony Remote Commander RM-V111T 取扱説明書 ガレージドア自動開閉装置 50
17 Sony RM-B750 取扱説明書 ガレージドア自動開閉装置 22
18 Sony RCP 920 取扱説明書 ガレージドア自動開閉装置 5
19 Aspire Digital ASPIRE RF RFKGT 取扱説明書 ガレージドア自動開閉装置 0
20 Aiphone IS-SS-HID-I 取扱説明書 ガレージドア自動開閉装置 0