ページ1に含まれる内容の要旨
Installation and operating instructions for
rolling door opener Model RDO800-series
Chamberlain GmbH
Alfred-Nobel-Strasse 4
66793 Saarwellingen
Germany
TEL: +49 (0) 6838/907-250
FAX: +49 (0) 6838/907-179
www.liftmaster.com
ページ2に含まれる内容の要旨
Start by Reading These Important Safety Instructions WARNING: Failure to comply with the following instructions may result in serious personal injury or property damage. • Read these instructions carefully and follow ALL instructions carefully • The garage door opener is designed and tested to offer reasonable safe service provided it is installed and operated in strict accordance with the instructions in this manual. These safety alert symbols mean WARNING – a personal safety or property damage
ページ3に含まれる内容の要旨
3 Door Requirements The maximum allowable door height is 4.5m, maximum allowable curtain area is 12.0m² (door height in metres multiplied by the width in metres) and maximum allowable door weight is 100kg. The Protector System™ (Safety Beams) must be installed if the force at the edge of the closing door force exceeds 400N (40kgf). Door shaft diameter must not exceed 35mm. Typical side room installation Minimum side room installation Ensure that there is at least 45mm from the edge of the curta
ページ4に含まれる内容の要旨
5 Prepare Opener Set Opener Position (Left or Right hand) For left hand side installations For right hand side installations the wire jumper should be removed. the wire jumper should be in place (factory installed). Attaching the Extension Poles (if required) 1. Insert the extension poles into the gear 2. Align the extension pole holes with the gear holes 3. Using the supplied screws secure the extension poles. Place the Opener in Manual Release mode. Pull the release cord down and across to e
ページ5に含まれる内容の要旨
6 Installation steps FOR RIGHT HAND INSTALLATIONS (REFER SECTION 5, page 3) 1. Ensure that the opener position jumper (wire connector) is in place (refer section 5, page 3). 2. Place the opener in manual release mode (refer section 5, page 3). 3. Open the roller door fully. For safety, tie a rope around the door. 4. Ensure that the U-bolt on the left hand side of the door is secure. 5. Mark the position of the door shaft on the right hand door bracket. 6. Carefully remove the U-bolt on the ri
ページ6に含まれる内容の要旨
7 Attach the Release Handle and Cord • Thread one end of the rope through the hole in the top of the Release cable red handle so “NOTICE” reads right side up as shown. Secure with an overhand knot at least 25mm from the end of the rope to prevent slipping. Rope • Thread the other end of the rope through the link on the emergency release cable. Manual Release • Adjust rope length so the handle is no higher than 1.8m Overhand knot Warning Label above the floor. Secure with an overhand knot.
ページ7に含まれる内容の要旨
L i f t M a s t e r 10 Program your Opener & Remote Please note your remote controls and wall plate have already been programmed into your operator. Activate the opener only when door is in full view, free of obstruction and properly adjusted. No one should enter or leave garage while door is in motion. Do not allow children to operate push button(s) or remote(s). Do not allow children to play near the door. Your garage door opener has already been programmed at the factory to operate wi
ページ8に含まれる内容の要旨
12 Setting the Force The force, as measured on the closing edge of the door, should not exceed 400N (40kgf). If the closing force is measured to more than 400N, the Protector System must be installed. See section 14. The force setting regulates the amount of power required to open and close the door. 1. Press the purple button (1) twice to enter opener into Force 1 2 Adjustment Mode. The indicator light (2) will flash quickly. 4 2. Press the green start button (4) on the bottom of the opener.
ページ9に含まれる内容の要旨
LOCK LIGHT LOCK LIGHT 15 Special Features 2 1 1.Motion Detecting Control Panel 3 Connect white/red wire to the red quick connect terminal and the white wire to the white quick connect terminal. 2.The Protector System™ (Safety Beams) Connect both white wires to the white quick connect 0 180 sec. terminal and both white/black wires to the grey quick 5 connect terminal. 50 3.Flashing light connection. The flashing light can be installed anywhere. 4.Battery Backup To access the battery backup co
ページ10に含まれる内容の要旨
Troubleshooting 1. The opener doesn't operate from either the green start button or the remote controls: • Does the opener have electric power? Plug a lamp into the outlet. If it doesn't light, check the fuse box. • Have you disabled all door locks? Review installation instruction warnings on page 1. • Is there a build-up of ice or snow under the door? The door may be frozen to the ground. Remove any restriction. • The garage door spring may be broken. Have it replaced. 2. Opener operates from t
ページ11に含まれる内容の要旨
MAINTENANCE OF YOUR OPENER SPECIFICATIONS Once a Month: Input Voltage: 230-240VAC, 50Hz, 90W • Repeat safety reverse test. Rated Load: 18Nm Make any necessary adjustments. Max.Pull Force: 550N • Manually operate door. If it is unbalanced or binding, call Max. Door Weight 100kg for professional garage door service. Idle Current: less than 25mA @ 230VAC • Check to be sure door opens and closes fully. Set Limits and/or Force if necessary. Drive: DC gearmotor permanent lubrication Max. Drum Rota
ページ12に含まれる内容の要旨
GARAGE DOOR OPENER WARRANTY Declaration of Conformity Chamberlain warrants to the first retail purchaser of this product that the product shall be free from any defect in materials and/or Automatic rolling door openers, as stated, are in conformity to the applicable sections of EN55014-1 workmanship for a period of 24 full months (2 years) from the (2000), EN55014-2 (1997), EN61000-3-2 (2000), EN61000-3-3 (1995), EN 301 489-3 (V1.3.1), date of purchase. Upon receipt of the product, the first re
ページ13に含まれる内容の要旨
Installation and operating instructions for rolling door opener Model RDO800GB Chamberlain GmbH Alfred-Nobel-Strasse 4 66793 Saarwellingen Germany TEL: +49 (0) 6838/907-250 FAX: +49 (0) 6838/907-179 www.liftmaster.com
ページ14に含まれる内容の要旨
Start by Reading These Important Safety Instructions WARNING: Failure to comply with the following instructions may result in serious personal injury or property damage. • Read these instructions carefully and follow ALL instructions carefully • The garage door opener is designed and tested to offer reasonable safe service provided it is installed and operated in strict accordance with the instructions in this manual. These safety alert symbols mean WARNING – a personal safety or property damage
ページ15に含まれる内容の要旨
3 Door Requirements The maximum allowable door height is 4.5m, maximum allowable curtain area is 12.0m² (door height in metres multiplied by the width in metres) and maximum allowable door weight is 100kg. The Protector System™ (Safety Beams) must be installed if the force at the edge of the closing door force exceeds 400N (40kgf). Door shaft diameter must not exceed 35mm. Typical side room installation Minimum side room installation Ensure that there is at least 45mm from the edge of the curta
ページ16に含まれる内容の要旨
5 Prepare Opener Set Opener Position (Left or Right hand) For left hand side installations For right hand side installations the wire jumper should be removed. the wire jumper should be in place (factory installed). Attaching the Extension Poles (if required) 1. Insert the extension poles into the gear 2. Align the extension pole holes with the gear holes 3. Using the supplied screws secure the extension poles. Place the Opener in Manual Release mode. Disengage: Pull the release cord down once
ページ17に含まれる内容の要旨
6 Installation steps FOR RIGHT HAND INSTALLATIONS (REFER SECTION 5, page 3) 1. Ensure that the opener position jumper (wire connector) is in place (refer section 5, page 3). 2. Place the opener in manual release mode (refer section 5, page 3). 3. Open the roller door fully. For safety, tie a rope around the door. 4. Ensure that the U-bolt on the left hand side of the door is secure. 5. Mark the position of the door shaft on the right hand door bracket. 6. Carefully remove the U-bolt on the ri
ページ18に含まれる内容の要旨
7 Attach the Release Handle and Cord Release cable • Thread one end of the rope through the hole in the top of the red handle so “NOTICE” reads right side up as shown. Secure with an overhand knot at least 25mm from the end of the rope to prevent slipping. Rope • Thread the other end of the rope through the link on the emergency release cable. Manual Release Overhand knot • Adjust rope length so the handle is no higher than 1.8m Warning Label above the floor. Secure with an overhand knot. I
ページ19に含まれる内容の要旨
L i f t M a s t e r 10 Program your Opener & Remote Please note your remote controls and wall plate have already been programmed into your operator. Activate the opener only when door is in full view, free of obstruction and properly adjusted. No one should enter or leave garage while door is in motion. Do not allow children to operate push button(s) or remote(s). Do not allow children to play near the door. Your garage door opener has already been programmed at the factory to operate wi
ページ20に含まれる内容の要旨
12 Setting the Force The force, as measured on the closing edge of the door, should not exceed 400N (40kgf). If the closing force is measured to more than 400N, the Protector System must be installed. See section 14. The force setting regulates the amount of power required to open and close the door. 1. Press the purple button (1) twice to enter opener into Force 1 2 Adjustment Mode. The indicator light (2) will flash quickly. 4 2. Press the green start button (4) on the bottom of the opener.
