Craftsman 139.18453Dの取扱説明書

デバイスCraftsman 139.18453Dの取扱説明書

デバイス: Craftsman 139.18453D
カテゴリ: ガレージドア自動開閉装置
メーカー: Craftsman
サイズ: 6.15 MB
追加した日付: 3/10/2014
ページ数: 80
説明書を印刷

ダウンロード

使い方は?

私たちの目的は、皆様方にデバイスCraftsman 139.18453Dの取扱説明書に含まれたコンテンツを可能な限り早く提供することです。オンラインプレビューを使用すると、Craftsman 139.18453Dに関してあなたが抱えている問題に対する解決策の内容が素早く表示されます。

便宜上

説明書Craftsman 139.18453Dをこちらのサイトで閲覧するのに不都合がある場合は、2つの解決策があります:

  • フルスクリーン表示 – 説明書を(お使いのコンピュータにダウンロードすることなく)便利に表示させるには、フルスクリーン表示モードをご使用ください。説明書Craftsman 139.18453Dのフルスクリーン表示を起動するには、全画面表示ボタンを押してください。
  • コンピュータにダウンロード - Craftsman 139.18453Dの説明書をお使いのコンピュータにダウンロードし、ご自身のコレクションに加えることもできます。デバイス上のスペースを無駄にしたくない場合は、いつでもManualsBaseサイトでダウンロードすることもできます。
Craftsman 139.18453D 取扱説明書 - Online PDF
Advertisement
« Page 1 of 80 »
Advertisement
印刷版

多くの人々は画面表示ではなく印刷された説明書を読むほうを好みます。説明書を印刷するオプションも提供されており、上記のリンクをクリックすることによりそれを利用できます - 説明書を印刷。説明書Craftsman 139.18453Dを全部印刷する必要はなく、選択したページだけを印刷できます。紙を節約しましょう。

要旨

次のページにある説明書Craftsman 139.18453Dの内容のプレビューは、以下にあります。次のページにある説明書の内容をすぐに表示したい場合は、こちらをご利用ください。

内容要旨
ページ1に含まれる内容の要旨

ENGLISH
Owner’s Manual
®
1/2 HP
GARAGE DOOR OPENER
For Residential Use Only
Models • 139.18451D • 139.18452D • 139.18453D • 139.18473D
Read and follow all safety rules ■ Safety Precautions
and operating instructions before
■ Assembly
first use of this product.
■ Installation
■ Adjustment
Fasten the manual near the garage
door after installation. ■ Maintenance
■ Operation
Periodic checks of the opener are
■ Troubleshooting
required to ensure safe operation.
■ Parts List
Sears Canada, Inc., Toront

ページ2に含まれる内容の要旨

TABLE OF CONTENTS Introduction 2-7 Adjustment 27-29 Safety symbol and signal word review........................2 Adjust the travel limits ...............................................27 Preparing your garage door ........................................3 Adjust the force .........................................................28 Tools needed...............................................................3 Test the safety reversal system.................................29 ® Planning ..........

ページ3に含まれる内容の要旨

1 Preparing your garage door WARNING WARNING Before you begin: To prevent possible SERIOUS INJURY or DEATH: � Disable locks. • ALWAYS call a trained door systems technician if garage CAUTION WARNING � Remove any ropes connected to garage door. door binds, sticks, or is out of balance. An unbalanced garage door may not reverse when required. � Complete the following test to make sure your garage door is balanced and is not sticking or binding: • NEVER try to loosen, move or adjust garage door, d

ページ4に含まれる内容の要旨

— — — — — — — — Planning Identify the type and height of your garage door. Survey � Look at the garage door where it meets the floor. Any your garage area to see if any of the conditions below gap between the floor and the bottom of the door must apply to your installation. Additional materials may be not exceed 1/4" (6 mm). Otherwise, the safety reversal required. You may find it helpful to refer back to this system may not work properly. See Adjustment Step 3. page and the accom

ページ5に含まれる内容の要旨

Planning (Continued) WARNING WARNING ONE-PIECE DOOR INSTALLATIONS Without a properly working safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED � Generally, a one-piece door does not require or KILLED by a closing garage door CAUTION . WARNING reinforcement. If your door is lightweight, refer to the • The gap between the bottom of the garage door and the information relating to sectional doors in Installation floor MUST NOT exceed 1/4" (6 mm). Otherwise, the

ページ6に含まれる内容の要旨

Carton Inventory Your garage door opener is packaged in one carton material. Parts may be stuck in the foam. Hardware for which contains the motor unit and all parts illustrated assembly and installation is shown on the next page. below. Accessories will depend on the model purchased. Save the carton and packing material until installation If anything is missing, carefully check the packing and adjustment is complete. Chain Spreader ® SECURITY✚ 3-Function Remote Control Models 18453D (2), 18473D

ページ7に含まれる内容の要旨

Hardware Inventory Separate all hardware and group as shown below for the assembly and installation procedures. ASSEMBLY HARDWARE Lock Washer Nut Lock Nut 3/8" (1) 3/8" (1) 1/4"-20 (2) Bolt 1/4"-20x1-3/4" (2) Master Link (2) Idler Bolt (1) Trolley Threaded Shaft (1) INSTALLATION HARDWARE Ring Handle Carriage Bolt Wing Nut Nut 5/16"-18 (8) Fastener (3) 1/4"-20x1/2" (2) 1/4"-20 (2) Lag Screw Hex Bolt Insulated 5/16"-9x1-5/8" (2) 5/16"-18x7/8" (4) Lock Washer 5/16" (7) Staples (30) Lag Screw Scr

ページ8に含まれる内容の要旨

WARNING WARNING ASSEMBLY STEP 1 CAUTION WARNING Assemble the Rail & Install the Trolley To prevent INJURY from pinching, keep hands and fingers away from the joints while assembling the rail. To avoid installation difficulties, do not run the garage door opener until instructed to do so. The front rail has a cut out “window” at the door end (see 4. As a temporary stop, insert a screwdriver into the hole illustration). The hole above this window is larger on 10" (25 cm) from the front end of the

ページ9に含まれる内容の要旨

WARNING WARNING ASSEMBLY STEP 2 CAUTION WARNING Fasten the Rail to the Motor Unit To avoid SERIOUS damage to garage door opener, use ONLY those bolts/fasteners mounted in the top of the opener. � Insert a 1/4"-20x1-3/4 bolt into the cover protection bolt hole on the back end of the rail as shown. Tighten securely with a 1/4"-20 lock nut. Do NOT overtighten. � Remove the two bolts from the top of the motor unit. Hex Screws � Place the “U” bracket, flat side down onto the motor 8-32x7/16" unit a

ページ10に含まれる内容の要旨

ASSEMBLY STEP 4 WARNING WARNING Install the Chain/Cable To avoid possible SERIOUS INJURY to fingers from moving garage door opener: 1. Pull the cable around the idler pulley and toward the CAUTION WARNING • ALWAYS keep hand clear of sprocket while operating trolley. opener. 2. Connect the cable to the retaining slot on the trolley, as • Securely attach chain spreader BEFORE operating. shown (Figure 1): � From below, push pins of master link bar up through Dispensing Carton cable link and trolley

ページ11に含まれる内容の要旨

ASSEMBLY STEP 5 Tighten the Chain Figure 1 Trolley � Spin the inner nut and lock washer down the trolley Outer Lock Threaded Nut Washer Shaft threaded shaft, away from the trolley. To Tighten Outer Nut � To tighten the chain, turn outer nut in the direction shown (Figure 1). Inner Nut � When the chain is approximately 1/4" (6 mm) above the base of the rail at its midpoint, re-tighten the inner To Tighten Inner Nut nut to secure the adjustment. Sprocket noise can result if chain is too loose. Fi

ページ12に含まれる内容の要旨

Unfinished INSTALLATION STEP 1 Ceiling OPTIONAL Determine the Header Bracket CEILING MOUNT Location FOR HEADER BRACKET Header Wall 2x4 WARNING WARNING Vertical Centerline To prevent possible SERIOUS INJURY or DEATH: of Garage Door • Header bracket MUST be RIGIDLY fastened to structural 2x4 Structural CAUTION WARNING support on header wall or ceiling, otherwise garage door Supports might not reverse when required. DO NOT install header bracket over drywall. • Concrete anchors MUST be used if moun

ページ13に含まれる内容の要旨

INSTALLATION STEP 2 Wall Mount Install the Header Bracket You can attach the header bracket either to the wall above the garage door, or to the ceiling. Follow the UP instructions which will work best for your particular requirements. Do not install the header bracket over drywall. If installing into masonry, use concrete anchors (not provided). Optional WALL HEADER BRACKET INSTALLATION Mounting Holes � Center the bracket on the vertical centerline with the bottom edge of the bracket on the hor

ページ14に含まれる内容の要旨

INSTALLATION STEP 3 Attach the Rail to the Header Bracket NOTE: (Optional) With some existing installations, you may re-use the old header bracket with the two plastic spacers included in the hardware bag. Place the spacers inside the bracket on each side of the rail, as illustrated. � Position the opener on the garage floor below the header bracket. Use packing material as a protective base. NOTE: If the door spring is in the way you’ll need help. Have someone hold the opener securely on a temp

ページ15に含まれる内容の要旨

WARNING WARNING INSTALLATION STEP 4 CAUTION WARNING Position the Opener To prevent damage to garage door, rest garage door opener rail on 2x4 placed on top section of door. Follow instructions which apply to your door type as illustrated. SECTIONAL DOOR OR ONE-PIECE DOOR WITH TRACK A 2x4 laid flat is convenient for setting an ideal door-to-rail distance. Rail � Remove foam packaging. � Raise the opener onto a stepladder. You will need help at this point if the ladder is not tall enough. � Open

ページ16に含まれる内容の要旨

INSTALLATION STEP 5 WARNING WARNING Hang the Opener To avoid possible SERIOUS INJURY from a falling garage door opener, fasten it SECURELY to structural supports of Three representative installations are shown. Yours may CAUTION the garage. Concrete anchors MUST be used if installing any WARNING be different. Hanging brackets should be angled (Figure brackets into masonry. 1) to provide rigid support. On finished ceilings (Figure 2 and Figure 3), attach a sturdy metal bracket to structural suppo

ページ17に含まれる内容の要旨

WARNING WARNING INSTALLATION STEP 6 CAUTION WARNING Install the Door Control To prevent possible SERIOUS INJURY or DEATH from electrocution: Locate door control within sight of door, at a minimum height of 5 feet (1.5 m) where small children cannot • Be sure power is not connected BEFORE installing door control. reach, away from moving parts of door and door hardware. If installing into drywall, drill 5/32" holes and • Connect ONLY to 24 VOLT low voltage wires. use the anchors provided. For To

ページ18に含まれる内容の要旨

NOTICE WARNING WARNING INSTALLATION STEP 7 CAUTION WARNING Install the Light To prevent possible OVERHEATING of the endpanel or light socket: � Press the release tabs on both sides of lens. Gently • DO NOT use short neck or specialty light bulbs. rotate lens back and downward until the lens hinge is • DO NOT use halogen bulbs. Use ONLY incandescent. in the fully open position. Do not remove the lens. To prevent damage to the opener: � Install a 100 watt maximum light bulb in the socket. • DO NO

ページ19に含まれる内容の要旨

INSTALLATION STEP 9 WARNING WARNING Electrical Requirements To prevent possible SERIOUS INJURY or DEATH from electrocution or fire: To avoid installation difficulties, do not run the CAUTION WARNING • Be sure power is not connected to the opener, and opener at this time. disconnect power to circuit BEFORE removing cover to To reduce the risk of electric shock, your garage door establish permanent wiring connection. opener has a grounding type plug with a third grounding • Garage door installatio

ページ20に含まれる内容の要旨

INSTALLATION STEP 10 WARNING WARNING ® Install The Protector System Be sure power is not connected to the garage door opener BEFORE installing the safety reversing sensor. The safety reversing sensor must be connected and CAUTION WARNING To prevent SERIOUS INJURY or DEATH from a closing aligned correctly before the garage door opener will garage door: move in the down direction. • Correctly connect and align the safety reversing sensor. This required safety device MUST NOT be disabled. IMPORTAN


類似の説明書
# 取扱説明書 カテゴリ ダウンロード
1 Craftsman 139.53315SR 取扱説明書 ガレージドア自動開閉装置 13
2 Craftsman 139.18473D 取扱説明書 ガレージドア自動開閉装置 2
3 Craftsman 139.18452D 取扱説明書 ガレージドア自動開閉装置 1
4 Craftsman 139.53225SRT 取扱説明書 ガレージドア自動開閉装置 6
5 Craftsman 139.53325SRT 取扱説明書 ガレージドア自動開閉装置 3
6 Craftsman 139.18451D 取扱説明書 ガレージドア自動開閉装置 3
7 Craftsman 139.18595 取扱説明書 ガレージドア自動開閉装置 1
8 Craftsman 139.53335SRT3 取扱説明書 ガレージドア自動開閉装置 2
9 Craftsman 139.53403 取扱説明書 ガレージドア自動開閉装置 0
10 Craftsman 139.53515SR - I/2HP 取扱説明書 ガレージドア自動開閉装置 21
11 Craftsman 139.53425SRT 取扱説明書 ガレージドア自動開閉装置 0
12 Craftsman 139.53610 取扱説明書 ガレージドア自動開閉装置 0
13 Craftsman 139.53625SR 取扱説明書 ガレージドア自動開閉装置 5
14 Craftsman 139.53628SRT 取扱説明書 ガレージドア自動開閉装置 12
15 Craftsman 139.53635SRT 取扱説明書 ガレージドア自動開閉装置 4
16 Sony Remote Commander RM-V111T 取扱説明書 ガレージドア自動開閉装置 50
17 Sony RM-B750 取扱説明書 ガレージドア自動開閉装置 22
18 Sony RCP 920 取扱説明書 ガレージドア自動開閉装置 5
19 Aspire Digital ASPIRE RF RFKGT 取扱説明書 ガレージドア自動開閉装置 0
20 Aiphone IS-SS-HID-I 取扱説明書 ガレージドア自動開閉装置 0