ページ1に含まれる内容の要旨
GPS NAVIGATION SYSTEM
DNX8220BT
MONITOR WITH DVD RECEIVER
DDX8022BT
INSTALLATION MANUAL
© B54-4650-00/00 (EW/E2W)
ページ2に含まれる内容の要旨
Accessories 1 ..........1 2 ..........1 3 ..........1 4 ..........1 5 ..........2 6 ..........1 7 DNX8220BT only ..........1 8 DNX8220BT only ..........1 9 ..........1 | 2 DNX8220BT/DDX8022BT
ページ3に含まれる内容の要旨
Installation Procedure • If your vehicle’s ignition does not have an ACC position, or 1. To prevent short circuits, remove the key from the if the ignition wire is connected to a power source with ignition and disconnect the - terminal of the constant voltage such as a battery wire, the power will not battery. be linked with the ignition (i.e., it will not turn on and off 2. Make the proper input and output wire along with the ignition). If you want to link the unit’s power connections f
ページ4に含まれる内容の要旨
Connection Connector A Ground wire (Black) Battery wire (Yellow) 8 6 4 2 7 5 3 1 Ignition wire (Red) FM/AM antenna 8 6 4 2 Antenna Cord input (JASO) 7 5 3 1 Connector B (Orange/White) Dimmer control wire (Orange/White) ILLUMI Connect to the vehicle's parking brake detection switch harness. Parking sensor wire (Light Green) PRK SW For the sake of safety, be sure to connect the parking sensor. Reveres sensor wire (Purple/White) Connect to vehicle's reverse lamp harness when using the optional
ページ5に含まれる内容の要旨
Bluetooth Microphone (Accessory 9) (see page 10) Cooling fan GPS Antenna (Accessory 7) (DNX8220BT only) (see page 10) FUSE ( 15A ) Accessory 1 REVERSE REMO.CONT MUTE ANT. CONT P CONT EXT.CONT | English 5
ページ6に含まれる内容の要旨
Connecting Wires to Terminals Connector Function Guide 2WARNING Pin Numbers for Cable Colour Functions Connecting the ISO Connector ISO Connectors The pin arrangement for the ISO connectors depends on External Power the type of vehicle you drive. Make sure to make the proper Connector connections to prevent damage to the unit. A-4 Yellow Battery The default connection for the wiring harness is described in A-5 Blue/White Power Control 1 below. If the ISO connector pins are set as described i
ページ7に含まれる内容の要旨
System Connection USB terminal (iPod) USB device (commercially available) USB terminal USB device (commercially available) iPod ■ Visual input (iPod) Resistance-free mini plug ■ Audio input (iPod) Resistance-free stereo type mini plug Accessory Accessory Accessory 4 2 3 ■ Audio/Visual Output • Visual output (Yellow) • Audio left output (White) • Audio right output (Red) ■ Audio/Visual input1 • Visual input (Yellow) • Audio left input (White) • Audio right input (Red) ■ Audio/Visual inp
ページ8に含まれる内容の要旨
Optional Accessory Connection iPod (commercially available) KCA-iP300V (Optional Accessory) Audio Output (Black) Navigation System Input (DDX8022BT only) Visual Output (Yellow) USB terminal USB terminal (iPod) iPod cannot be connected. USB terminal TV Tuner (Optional Accessory) Navigation System (Optional Accessory) Connection cable (Included in the TV tuner) Connection cable (Included in the Navigation System) | 8 DNX8220BT/DDX8022BT iPod TO
ページ9に含まれる内容の要旨
Installation for Monitor/Player Unit Firewall or metal support Screw (M4X8) (commercially available) Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. Self-tapping screw Metal mounting strap (commercially available) (commercially available) Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (eg, the sound may skip). Installing the Escutcheon 1. Attach accessory 6 to the unit. Accessory 6 | Engli
ページ10に含まれる内容の要旨
Installing the GPS Antenna Installing the Microphone Unit (DNX8220BT only) GPS antenna is installed inside of the car. It should 1. Check the installation position of the microphone be installed as horizontally as possible to allow easy (accessory 9). reception of the GPS satellite signals. 2. Remove oil and other dirt from the installation To mount the GPS antenna inside your vehicle: surface. 1. Clean your dashboard or other surface. 3. Install the microphone. 2. Peel the backing off of th
ページ11に含まれる内容の要旨
Removing Monitor/Player Unit Removing the Hard Rubber Frame Removing the Unit (escutcheon) 1. Remove the hard rubber frame by referring to the removal procedure in the section . remove the two locks on the lower level. 2. Remove the Hex-head screw with integral washer Lower the frame and pull it forward as shown in (M4 × 8) on the back panel. the figure. 3. Insert the two removal tools 5 deeply into the Acce
ページ12に含まれる内容の要旨
