Teledyne HFM-300の取扱説明書

デバイスTeledyne HFM-300の取扱説明書

デバイス: Teledyne HFM-300
カテゴリ: 自動車部品
メーカー: Teledyne
サイズ: 0.82 MB
追加した日付: 11/7/2014
ページ数: 31
説明書を印刷

ダウンロード

使い方は?

私たちの目的は、皆様方にデバイスTeledyne HFM-300の取扱説明書に含まれたコンテンツを可能な限り早く提供することです。オンラインプレビューを使用すると、Teledyne HFM-300に関してあなたが抱えている問題に対する解決策の内容が素早く表示されます。

便宜上

説明書Teledyne HFM-300をこちらのサイトで閲覧するのに不都合がある場合は、2つの解決策があります:

  • フルスクリーン表示 – 説明書を(お使いのコンピュータにダウンロードすることなく)便利に表示させるには、フルスクリーン表示モードをご使用ください。説明書Teledyne HFM-300のフルスクリーン表示を起動するには、全画面表示ボタンを押してください。
  • コンピュータにダウンロード - Teledyne HFM-300の説明書をお使いのコンピュータにダウンロードし、ご自身のコレクションに加えることもできます。デバイス上のスペースを無駄にしたくない場合は、いつでもManualsBaseサイトでダウンロードすることもできます。
Teledyne HFM-300 取扱説明書 - Online PDF
Advertisement
« Page 1 of 31 »
Advertisement
印刷版

多くの人々は画面表示ではなく印刷された説明書を読むほうを好みます。説明書を印刷するオプションも提供されており、上記のリンクをクリックすることによりそれを利用できます - 説明書を印刷。説明書Teledyne HFM-300を全部印刷する必要はなく、選択したページだけを印刷できます。紙を節約しましょう。

要旨

次のページにある説明書Teledyne HFM-300の内容のプレビューは、以下にあります。次のページにある説明書の内容をすぐに表示したい場合は、こちらをご利用ください。

内容要旨
ページ1に含まれる内容の要旨

TELEDYNE
HASTINGS
INSTRUMENTS
INSTRUCTION MANUAL
HFM-300 FLOW METER,
HFC-302 FLOW CONTROLLER
ISO 9001
CER T IFIED

ページ2に含まれる内容の要旨

Manual Print History The print history shown below lists the printing dates of all revisions and addenda created for this manual. The revision level letter increases alphabetically as the manual undergoes subsequent updates. Addenda, which are released between revisions, contain important change information that the user should incorporate immediately into the manual. Addenda are numbered sequentially. When a new revision is created, all addenda associated with the previous revision of the

ページ3に含まれる内容の要旨

Table of Contents 1. GENERAL INFORMATION............................................................................................................................................ 4 1.1. FEATURES.................................................................................................................................................................... 4 1.2. SPECIFICATIONS.................................................................................................................

ページ4に含まれる内容の要旨

1. General Information The Teledyne Hastings HFM-300 is used to measure mass flow rates in gases. In addition to flow rate measurement, the HFC-302 includes a proportional valve to accurately control gas flow. The Hastings mass flow meter (HFM-300) and controller (HFC-302), hereafter referred to as the Hastings 300 series, are intrinsically linear and are designed to accurately measure and control mass flow over the range of 0-5 sccm to 0-10 slm with an accuracy of better than ±0.75

ページ5に含まれる内容の要旨

1.2. Specifications Accuracy .................................................................................... < ±0.75% full scale (F.S.) at 3σ (±1.0% F.S. for >10 slm versions) Repeatability .............................................................................±0.05% of reading + 0.02% F.S. Maximum Pressure........................................................................................500 psi [3.45 MPa] (With high pressure option) 1000 psi [6.9 MPa] Pressure Coefficient

ページ6に含まれる内容の要旨

The 4-20 mA I/O option can accept a current input. The 0-5 VDC command signal on pin 14 can be replaced by a 4-20mA command signal. The loop presets an impedance of 75 ohms and is returned to the power supply through the valve common. 1.4. Other Accessories 1.4.1. Hastings Power supplies Hastings Power Pod power supply/display units are available in one and four channel versions. They convert 100, 115 or 230VAC to the ±15 VDC required to operate the fl

ページ7に含まれる内容の要旨

2. Installation and Operation This section contains the steps necessary to assist in getting a new flow meter/controller into operation as quickly and easily as possible. Please read the following thoroughly before attempting to install the instrument. 2.1. Receiving Inspection Carefully unpack the Hastings unit and any accessories that have also been ordered. Inspect for any obvious signs of damage to the shipment. Immediately advise the carrier who delivered the shipment if any dam

ページ8に含まれる内容の要旨

2.4. Mechanical Connections 2.4.1. Filtering The smallest of the internal passageways in the Hastings 300 is the diameter of the sensor tube, which is 0.026”(0.66 mm), and the annular clearance for the 500 sccm shunt which is 0.006"(0.15 mm) (all other flow ranges have larger passages), so the instrument requires adequate filtering of the gas supply to prevent blockage or clogging of the tube. 2.4.2. Mounting There are two mounting holes (#8-32 thread) in the bottom of the transducer tha

ページ9に含まれる内容の要旨

Fig. 2.1 Fig. 2.2 Figures 2.1/2.2, and Tables 2.1/2.2, show the 300/302 pin out. Table 2.1 Table 2.2 "U" Pin-Out "H" Pin-Out Pin # Pin # 1 Signal Common 1 Do not use 2 Do not use 2 Do not use 3 Do not use 3 Do not use 4 +15 VDC 4 Do not use 5 5 Signal Common 6 Output 0-5 VDC (4-20mA) 6 Output 0-5 VDC (4-20mA) 7 Signal Common 7 Case Ground 8 Case Ground 8 Valve Override 9 Valve Override 9 -15VDC 10 10 Do not use 11 -15VDC 11 +15VDC 12 External Input 12 Signal Common 1

ページ10に含まれる内容の要旨

2.6.2. Zero Check Turn the power supply on if not already energized. Allow for a 1 hour warm-up. Stop all flow through the instrument and wait 2 minutes. Caution: Do not assume that all metering valves completely shut off the flow. Even a slight leakage will cause an indication on the meter and an apparent zero shift. For the standard 0-5 VDC output, adjust the zero potentiometer located on the inlet side of the flow meter until the meter indicates zero (Fig 2.3). For the optional

ページ11に含まれる内容の要旨

Span Error Vs. Pressure Fig. 2.5 0.017" Sensor 5% 4% 3% 2% 1% 0% Mean Max -1% Min -2% 0 100 200 300 400 500 600 700 800 900 1000 Pressure (psig) If the system pressure is higher than 250 psig (1.7 MPa) the pressure induced error in the span reading becomes significant. The charts above show the mean error enveloped by the minimum/maximum expected span errors induced by high pressures. This error will approach 16% at 1000 psig. For accurate high pressure measurements this error must be

ページ12に含まれる内容の要旨

The first method requires that the two controllers use the same signal range (0 to 5 VDC or 4 to 20 mA) and that they be sized and calibrated to provide the correct ratio of gasses. Then, by routing the actual flow Output signal from the primary meter/controller through the secondary controller’s External Input pin (See Tables 2.1 & 2.2), the ratio of flows can be maintained over the entire range of gas flows. EXAMPLE: Flow controller A has 0-100 slpm range with a 5.00 volt output at full

ページ13に含まれる内容の要旨

variable directly. This analog output signal could be 0-5 volts, 0-10 volts (or 4-20 ma for units with 4- 20 ma boards) or any value in between. On the controller card there is a jumper that sets whether the control loop controls mass flow or an external process variable. See Figure 2.7. If the jumper is over the top two pins, the loop controls mass flow. If the jumper is over the bottom two pins, the loop controls an external process variable. This process variable signal must be suppl

ページ14に含まれる内容の要旨

2.12. Temperature Coefficients As the ambient temperature of Fig. 2.8 the instrument changes from the original calibration temperature, errors will be introduced into the output of the instrument. The Temperature Coefficient of Zero describes the change in the output that is seen at zero flow. This error is added to the overall output signal regardless of flow, but can be eliminated by merely adjusting the zero potentiometer of the flow meter/controller to read zero volts at z

ページ15に含まれる内容の要旨

3. Theory of Operation This section contains an overall functional description of the Hastings 300 series of flow instruments. In this section and other sections throughout this manual, it is assumed that the customer is using a Hastings power supply. 3.1. Overall Functional Description The Hastings 300 meter consists of a sensor, base, and a shunt. In addition to the components in a meter, The 300 controller includes a control valve and extra electronic circuitry. The sensor is c

ページ16に含まれる内容の要旨

low temperatures used by the sensor, and because the sensor construction preferentially favors the conductive and convective heat transfer modes. The thermal energy of each heater will then be dissipated by conduction down the stainless steel sensor tube, conduction to the insulating foam, plus the convection due to the mass flow of the sensed gas. Because great care is taken to wind the resistive heater coils symmetrically about the midpoint of the tube, it is assumed that the heat condu

ページ17に含まれる内容の要旨

The gas stream will increase in temperature due to the heat it gains from the upstream heater. This elevated gas stream temperature causes the heat transfer at the downstream heater to gain heat from the gas stream. The heat gained from the gas stream forces the downstream bridge control loop to apply less power to the downstream heater coil in order to maintain a constant differential o temperature of 48 C. The power difference at the RTD’s is a function of the mass flow rate and the sp

ページ18に含まれる内容の要旨

the shunt. Most instruments employ Poiseuille’s law and use some sort of multi-passage device that creates laminar flow between the upstream sensor inlet and the downstream outlet. This makes the volumetric flow versus pressure drop curve primarily linear, but there are other effects which introduce higher order terms. Most flow transducers are designed such that the outlet plenum has a smaller diameter than the inlet plenum. This eases the insertion and containment of the shunt

ページ19に含まれる内容の要旨

Qρ L = (3.5) e 5πμ For a typical flow divider tube the entry length is approximately 0.16 cm. From this it can be seen that if the sensor inlet pickup point is inside of the flow divider tube but downstream of the entrance length and if the sensor outlet point is inside the flow divider tube but upstream of the exit point then the pressure drop that drives the flow through the sensor would be linear with respect to volumetric flow rate. Since the pressure drop a

ページ20に含まれる内容の要旨

Fig. 3.5 Thickness of the annular ring as a function of flow rate for a sensor with a 75 Pa drop and a 2 cm spacing. 0.18 0.16 0.14 0.12 0.1 0.08 0.06 0.04 0.02 0 0 5 10 15 20 25 30 35 Flow (liter/min) Each shunt must have a section of the annular region upstream of the upstream sensor tap to allow the flow to become fully developed before reaching the first tap. The entry length for the annular passage is then: Qρ() Δr


類似の説明書
# 取扱説明書 カテゴリ ダウンロード
1 Teledyne HASTINGS 200 取扱説明書 自動車部品 3
2 Teledyne 203 取扱説明書 自動車部品 0
3 Teledyne 201 取扱説明書 自動車部品 1
4 Teledyne 202 取扱説明書 自動車部品 0
5 Teledyne 200 取扱説明書 自動車部品 0
6 Teledyne 207 取扱説明書 自動車部品 0
7 Teledyne HFC-302 取扱説明書 自動車部品 0
8 Teledyne HFC-303/307 取扱説明書 自動車部品 0
9 Teledyne 205 取扱説明書 自動車部品 0
10 Teledyne HFM-I-401 取扱説明書 自動車部品 0
11 Teledyne HFM-I-405 取扱説明書 自動車部品 1
12 Teledyne 730 Bubbler 取扱説明書 自動車部品 0
13 Sony BP-GL95 取扱説明書 自動車部品 25
14 Sony BP-GL65 取扱説明書 自動車部品 2
15 Philips Epic 50PF9966 取扱説明書 自動車部品 3
16 Philips HTS3011 取扱説明書 自動車部品 2
17 Philips SDJ6040W 取扱説明書 自動車部品 1