ページ1に含まれる内容の要旨
OPERATION
®
Mode: On-Time: Works: Day Night
Test 5 Sec x x
Auto 1, 5, 20 min. x
Twin Halogen
Manual Until Dawn* x
* resets to Auto Mode at dawn.
Motion Sensing
1
Note: When fi rst turned on wait about 1 / minutes for
2
the circuitry to calibrate.
Light with 2-Level
TEST
Lighting
2-Level
Put ON-TIME switch ON-TIME
Lighting
on the sensor bot-
Model 5512 tom to TEST and
TEST 1 5 20
the 2-Level Lighting
Off 3 6 Dusk to
Features
switch OFF.
Dawn
� Turns on lighting when motio
ページ2に含まれる内容の要旨
INSTALLATION WIRE THE LIGHT CONTROL For easy installation, select an existing light operated WARNING: Turn power off at circuit breaker. by a wall switch for replacement. ❒ Remove the existing light fi xture. For best performance, mount the fi xture about 8 ft. (2.4 m) ❒ Install mounting strap to junction box using screws above the ground. appropriate for your junction box. ❒ The plastic hanger can be used to hold the fi xture CAUTION: Keep the sensor at least 1" (2.5 cm) while wiring. The sm
ページ3に含まれる内容の要旨
T S O O B ❒ Loosen the clamp screw in the Clamp TEST AND ADJUSTMENT sensor ball joint and gently Screw ❒ Turn on the circuit breaker and light switch. rotate the sensor. 1 ❒ Walk through the coverage NOTE: Sensor has a 1 / minute warm up period be- 2 Ball area noting where you are fore it will detect motion. When fi rst turned on Joint when the lights turn on. Move 1 or when switching modes wait 1 / minutes. 2 the sensor head up, down, or sideways to change the cover- ❒ Turn the RANGE c
ページ4に含まれる内容の要旨
TROUBLESHOOTING GUIDE SYMPTOM POSSIBLE CAUSE SYMPTOM POSSIBLE CAUSE Lights will 1. Light switch is turned off. Lights stay 1. A lamp is positioned too close to the on continu- not come on. 2. Light is loose or burned out. sensor or pointed at nearby objects ously. 3. Fuse is blown or circuit breaker is that cause heat to trigger the sensor. turned off. (Reposition the lamp away from the 4. Daylight turn-off is in effect (Recheck sensor or nearby objects). after dark). 2. Sensor is pointed to
ページ5に含まれる内容の要旨
1 Cuando lo prenda por primera vez espere 1 / minutos 2 hasta que el circuito se calibre. ® Para PRUEBA: Luz gemela de halógeno Ponga el interruptor de ON-TIME Alumbrado Duración (ON-TIME) que de 2 niveles detectora de movimiento está en la parte inferior TEST 1 5 20 del detector en Prueba con 2 niveles de alumbrado Off 3 6 Dusk to (TEST) y el interruptor de alumbrado Dawn de 2 niveles en Apagado (OFF). Modelo 5512 Características Para AUTOMATICO: � Prende la luz cuando detecta movimie
ページ6に含まれる内容の要旨
INSTALACION CONECTE EL CONTROL DE LUZ Para una fácil instalación escoja una luz con un interruptor ADVERTENCIA: Apague la energía en el fusible de pared. o cortacircuitos. Para un mejor funcionamiento, instale el aparato a casi ❒ Quite el aparato de luz existente. 2,4 m del suelo. ❒ Instale la lámina de montaje a la caja de empalme usan- CUIDADO: Mantenga al detector por lo menos a 2.5 do tornillos apropiados para la caja de empalme. cm de las lámparas. ❒ Se puede usar el colgador plástico
ページ7に含まれる内容の要旨
T S O O B ❒ Afl oje el tornillo sujetador Tornillo PRUEBA Y AJUSTE en la unión esférica y gire Sujetador ❒ Prenda el cortacircuitos y el interruptor de luz. despacio el detector. 1 NOTA: El detector tiene un período de cerca de 1 / 2 Unión ❒ Camine por el área a prote- minutos de calentamiento antes de detectar Esférica gerse y dése cuenta dónde movimiento. Cuando lo prenda por primera está cuando se prende la 1 vez, espere 1 / minutos. 2 luz. Mueva la cabeza del detector hacia arriba,
ページ8に含まれる内容の要旨
GUIA DE INVESTIGACION DE AVERIAS SINTOMA POSIBLE CAUSA SINTOMA POSIBLE CAUSA La luz no se 1. El interruptor de luz está apagado. La luz se queda 1. Un faro está colocado demasiado cerca enciende. 2. El faro está fl ojo o fundido. prendida con- al detector o apunta a objetos cercanos 3. El fusible está quemado o el cortacircuitos tinuamente. que hacen que el calor active el detector. está apagado. (Reposicione la lámpara lejos del detec- 4. La desconexión de luz del día está en tor o de los obj