ページ1に含まれる内容の要旨
Supported Equipment Manual
For the DT-800RF Device Manufactured by Casio
ページ2に含まれる内容の要旨
Copyright © 1996 - 2006 by Connect, Inc. All rights reserved. This document may not be reproduced in full or in part, in any form, without prior written permission of Connect Inc., 1701 Quincy Avenue, Suites 5 & 6, Naperville, IL 60540. Connect, Inc. makes no representation or warranties with respect to the contents of this document and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. Further, Connect, Inc. reserves the right to r
ページ3に含まれる内容の要旨
Table of Contents Chapter 1 • Introduction............................................................................................. 1-1 Description………………… ..........................................................................................1-1 Picture………………………...........................................................................................1-2 Setup Requirements…….. ...........................................................................................1-2 Accessories
ページ4に含まれる内容の要旨
This page is intentionally blank. iv Supported Equipment Manual • March, 2006
ページ5に含まれる内容の要旨
Chapter 1 • Introduction Description The DT-800RF has a versatile high-speed scanning (100 scans per second) that ensures a rapid first-time read rate and high data integrity. Its combination of distance and contact laser scanning allows bar codes to be easily read even when badly printed on curved and irregular surfaces. Amongst the lightest weight terminals in its class, the compact lightweight design of the DT-800RF reduces operator fatigue over extended usage periods. Its backl
ページ6に含まれる内容の要旨
Introduction Picture Setup Requirements Installation of PowerNet Twin Client requires, at a minimum, the following: • A Pentium-class processor • 32 MB of RAM • 10 MB of free hard disk space available • Microsoft Windows 95, 98, ME, XP, or NT/2000 operating system Accessories The following accessories are available for the DT-800RF: I/O Box • DT-860IOE (satellite I/O box) • DT-865IOE (master I/O box) Charger (Single-Pack) • DT-820CHGE (Quick charger) Lith
ページ7に含まれる内容の要旨
Accessories AC Adaptors • DT-9020ADPG (AC adaptor (230V) for DT-820CHGE) • DT-9020ADPU (AC adaptor (120V) for DT-820CHGE) • DT-825ADP-G (AC adaptor (230V) for I/O boxes) • DT-825ADP-U (AC adaptor (120V) for I/O boxes) Cables • DT-881RSC-E: RS232C Modem cable • DT-882RSC-E: RS232C Cross cable (between DT860IO-E and PC: 25pin male) • DT-883RSC-E: RS232C Cross cable (between DT860IO-E and PC: 25pin female) • DT-887AX: RS232C Cross cable (between DT86
ページ8に含まれる内容の要旨
Introduction Operating System Version of the Operating System The version of the operating system on a DT-800RF terminal is 2.00. Finding the Version of the Operating System The version of operating system will appear on a terminal screen when the terminal is rebooted. For rebooting instructions, see Command Mode Boot in the Quick Start section. 1-4 Supported Equipment Manual • March, 2006
ページ9に含まれる内容の要旨
Chapter 2 • Terminal Setup Running Setup from a Download File The downloaded file is a compressed archive. After extraction using a utility such as WinZip or PKWARE, folders are created on the hard disk as shown in the following figure. Click on the Disk1 folder to view the files as shown in the following figure. Click on the Setup application and proceed to the following section entitled Installation for further instructions. 2-1 Supported Equipment Manual • March, 2006
ページ10に含まれる内容の要旨
Terminal Setup Installation The InstallShield wizard runs and presents the following screen. Click on Next to begin the installation process. 2-2 Supported Equipment Manual • March, 2006
ページ11に含まれる内容の要旨
Installation To change the default Destination Location, click on Browse and select a location. Then click on Next. The default folder is PowerNet. This default may be changed either by selecting an existing program group or by typing in a new name at the prompt. Then click on Next. When the installation is complete, reboot the system to initialize the Twin Client software. 2-3 Supported Equipment Manual • March, 2006
ページ12に含まれる内容の要旨
Terminal Setup a. To reboot the system immediately, click on Finish. b. To reboot later, click on the option to restart the computer later, and click on Finish. Running the Manager The PowerNet Twin Client Manager is the utility that manages the terminal software and configurations. Select Start, Programs, PowerNet, and Twin Client Manager. The PowerNet Twin Client Manager screen appears as shown in the following figure. This is the administrator's main screen, and all functions are ac
ページ13に含まれる内容の要旨
Quick Start Quick Start Quick Start describes how to prepare the Twin Client Manager and the Casio terminal for a Telnet session with the host. Following an initial serial download, the terminal software and configuration is managed automatically, over the wireless network. Configuring the Manager The first step is to configure the Twin Client Manager to meet site-specific requirements, and then prepare it for the automatic management of the terminal software and IP addresses. This sim
ページ14に含まれる内容の要旨
Terminal Setup To set these addresses from the Settings menu, click on Servers and then click on Add. Enter the name of each server, its IP Address and IP port (normally 23 for Telnet servers), and emulation type. Then click on OK. Repeat this step for each telnet server the terminals are required to access. If an error is made in the name, IP Address, IP Port number, or Terminal emulation type, click on the line that is in error and then click on the Edit button to make the corrections
ページ15に含まれる内容の要旨
Quick Start Saving the Configuration Click File and Save As. Enter a name for this configuration. For the purposes of this example, the name is vt100. 2-7 Supported Equipment Manual • March, 2006
ページ16に含まれる内容の要旨
Terminal Setup Download Files to Terminal Select Terminal and Send Program Files to Terminal from the menu bar. The program asks if you want to include configuration files. Select Yes. The Casio Load Options screen appears telling you what actions to perform on the terminal. The first three of these instructions perform the terminal reboot. The remainder perform the actual download. Click OK. The Casio CD-ROM, distributed with Casio terminals, contains LMWIN2 in the directory
ページ17に含まれる内容の要旨
Quick Start Select Execute from the menu bar, then select Link Manager and select Start Link Manager. Note: A shortcut is to just click on the start icon. To stop the download, select Execute then Link Manager Stop, or press the Stop key, the fifth icon from the left under the Download/Upload Utility menu. After the files are sent, close the Download/Upload Utility to return to the Twin Client Configuration Utility main screen and proceed. The PowerNet Twin Client startup screen i
ページ18に含まれる内容の要旨
Terminal Setup Connecting the Cradle The terminal download requires a serial connection between the terminal and the PC through a cradle. Connect the serial load cable from a serial port on the PC to the communications port of the terminal cradle or to a Casio terminal. In preparation for this download perform the following: • Make sure you have copied the LMWIN utility to any directory on your PC. • Connect the selected serial port on the PC to the cradle with a null modem cable. Use C
ページ19に含まれる内容の要旨
Quick Start 3. Press the Clear key. 4. Select 1: yes. 5. Press the Clear key to return to the system menu. 6. Select 4: Transmit, 4: Utility and 4: Change memory size. 7. Enter 640 and then press the Enter key. 8. Select yes to change the size. 9. Press the Clear key to return to the system menu. 10. Select 1: Execute AP. 11. Select Enter for “yes” to execute the AP. The terminal is now configured to accept a download from Twin Client Manager. Starting a Telnet Session At the
ページ20に含まれる内容の要旨
Terminal Setup Standard Setup The default terminal setup is sufficient for most installations. However, to meet site- specific requirements, it may be necessary to customize terminal operation. The standard setup options simplify this process and can be modified using one of the following methods: • Using the Twin Client Manager. • Using the Twin Client terminal menu system. Standard Setup describes how to use the Twin Client Manager and the terminal menu systems to set up the terminal.
