ページ1に含まれる内容の要旨
®
SeaLand
GRAvITy dISchARGe ToILeT
oWNeR’S MANuAL
®
SeaLand 3200 Series All-ceramic Toilets
WARNING
!
This manual must be read and under-
stood before installation, adjustment,
service, or maintenance is performed.
Modification of this product can result
in property damage.
dometic Sanitation corporation
328 State Rt 226, PO Box 38
Big Prairie, OH 446
SeaLand Product Customer Service: -800-32-9886
(8:00 a.m. - 5:00 p.m. ET)
ページ2に含まれる内容の要旨
TAbLe of coNTeNTS Toilet Model Identification .....................................2 Deodorants and Special Tissue ............................8 Toilet Dimensions ..................................................3 Flush Mechanism Components .............................9 Installation Instructions .................................... 3 - 6 Troubleshooting ...................................................0 Toilet Operation .....................................................6 Wiring Diagr
ページ3に含まれる内容の要旨
ToILeT dIMeNSIoNS ModeL 3210 Dimensions may vary ±3/8-inch (13mm). INSTALLATIoN INSTRucTIoNS System Requirements: • 2 GPM (0.6 lpm) or larger water pump. • 1/2-inch (12.7 mm) water line terminating in 1/2-inch MPT fitting (to connect to toilet water supply hose). • 4-bolt floor (closet) flange. SeaLand flanges available include 3-inch spigot, socket, MPT, or 45-degree swivel socket. • 2 VDC through 2-amp fuse or circuit breaker. Use 4-gauge stranded copper wire. STEP 1: Carefully unpack
ページ4に含まれる内容の要旨
STEP 5a: For through-the-floor water line and electrical wires, mark another centerline 6 inches (52 mm) from below-floor Installation the back wall (fig. 4). fig. 4 STEP 5b: For through-the-wall water line and electrical Above-floor Installation wires, mark a centerline 8 inches (203 mm) up from the floor centerline (fig. 5). fig. 5 STEP 7: Insert floor flange into larger hole and secure to the floor with #12x3/4-inch long flat head wood or STEP 6: Make a 4-3/4 inch (2 mm) diameter ho
ページ5に含まれる内容の要旨
STEP 9: WITh The eLecTRIcAL PoWeR off , route STEP 13: Temporarily set the toilet in place on the floor #14 gauge stranded copper wire from 12 VDC ground flange (fig. 14). and positive 2 VDC from the fuse panel through a 2-amp fuse or circuit breaker. Leave at least 2 inches (305 mm) of wire for connecting to toilet (fig. 9). fig. 9 fig. 14 STEP 0: Connect the holding tank to the bottom of the STEP 4: Mark the holes for the two toilet mounting discharge flange. bolts (fig. 15)
ページ6に含まれる内容の要旨
STEP 7: Connect the positive (+) 2 VDC lead to the red wire and the negative (-) lead to the black wire (fig. 8). Fig. 18 fig. 19 fig. 20 STEP 8: Re Move Red c AP f Ro M MIdd Le of f LANGe AdAPTeR befo Re f INAL To ILeT INSTALLATIoN. IMPo RTANT – do No T ATTeMPT To SLIde The To ILe T ove R The f LANGe Ad APTe R. The To ILeT MuST be SeT do WN ove R The AdAPTeR To PReve NT Po SSIbLe dAMAGe. fig. 21 STEP 19: Set the toilet in place (fig. 19) and secure to floor with the #14x2
ページ7に含まれる内容の要旨
PRoPeR cLeANING ANd MAINTeNANce Clean your SeaLand toilet regularly for maximum sanitation and operational ef- fig. A ficiency. You can clean it just as you would a household toilet. do not use caustic chemicals, such as drain-opening types, as they will damage the seals. bo WL c LeANING: For stubborn stains, use SeaLand Toilet Bowl Cleaner (fig. A). It’s manufactured especially for use with SeaLand ceramic toilets. In certain locations where water is hard, a build-up of lime may dull the
ページ8に含まれる内容の要旨
deodoRANTS ANd SPecIAL TISSue Your SeaLand toilet requires the regular addition of a deodorant product to reduce malodors and to help break down holding tank contents. Several factors should be considered in selecting a deodorant product. Liquid or dry: Liquid products obviously work more quickly by readily going into solution. Granulated powder formulations, on the other hand, have the advantage of requiring less storage space and are less likely to leak if the package is inadvertently
ページ9に含まれる内容の要旨
Flu SH Mec Hani SM c o Mponent S 1. To access base 3. Lift china toilet straight up from base assembly components, and set it down just in remove decorative screw caps and unscrew two front of floor flange. bolts that hold china toilet Turn off water to to floor. toilet and disconnect flexible water line. Disconnect power 2. Remove access wires if necessary. cover from top of china and set it aside. Ba Se a SSeMBl Y co Mponent S Water Valve (under ceramic toilet) Vacuum Switch
ページ10に含まれる内容の要旨
TRoubLeShooTING Important: Always turn off electrical power and water to the toilet for disassembly. Problem Possible cause Service Instructions 1. Toilet emits odor (flush ball a. Odor emitting from base of toilet. a. Use SeaLand brand deodorants. open). b. Plugged holding tank vent line. b. Clear obstructions from vent line. 2. Water will not stay in bowl. a. Improper seal between flush ball a. Clean underside of flush ball seal and seal due to dirt or debris on (see cleaning method on pag
ページ11に含まれる内容の要旨
WIRING dIAGRAM SeALANd T oILeT oRdeRING P ARTS Dometic is ready to assist you in the event service is required. Before calling, please have the following informa- tion available. Your cooperation in having this information ready is appreciated and allows us to better meet your needs. . Toilet Model Number 2. Serial Number 3. Part Number, Description and Quantity (see separate Parts List)
ページ12に含まれる内容の要旨
cuST oMeR SeR vIce There is a strong, worldwide network to assist in servicing and maintaining your sanitation system. For the Authorized Service Center near you, please call from 8:00 a.m. to 5:00 p.m. (ET) Monday through Friday. Telephone: 1 800-321-9886 U.S.A. and Canada 330-496-3211 International Email: sealand@dometicusa.com Mail: dometic Sanitation corporation 13128 SR 226 PO Box 38 big Prairie, oh 44611 MANuf AcTuReR’S TWo-yeAR ANd TeN-yeAR LIMITed W ARRANTIeS ® Dometic
