ページ1に含まれる内容の要旨
OWNER’S MANUAL
FREEDOM 458 Series COMBI
TM
INVERTER/CHARGER
MODEL 15 Part No. 81-1510-12
MODEL 15D Part No. 81-1520-12
MODEL 20 Part No. 81-2010-12
MODEL 20D Part No. 81-2020-12
INFORMATION IN THIS MANUAL IS SUBJECT TO CHANGE WITHOUT NOTICE
®
A Valley Forge Company
1
Part No. 90-0123-00
Libertycombi.p65 10/26/98
ページ2に含まれる内容の要旨
Thank you for purchasing a Heart Interface Freedom 458 Series Combi Inverter/ TM Charger. Heart Interface takes pride in manufacturing quality products specifically designed to meet your power requirements. Freedom Combi Inverter/Chargers provide silent, efficient and reliable AC power for a variety of applications. They feature “hands-free” operation, automatic 3-stage battery charging and automatic AC transfer switching. For your convenience, service is available world-wide by qualified serv
ページ3に含まれる内容の要旨
TABLE OF CONTENTS Introduction. . . . . . . . . . . . . . . . . . . . . . . . . 4 Troubleshooting . . . . . . . . . . . . . . . . . . . . .31 LED Fault Status Things You Should Know . . . . . . . . . . . . . 5 Things to Check Circuit Breaker Protection Thermostat Controlled Cooling Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 Inverter Idle Circuit Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 35 Low and High Battery Shutdown Power Sharing
ページ4に含まれる内容の要旨
INTRODUCTION This owner’s manual describes the power through directly to the loads. When the Freedom 458 Series Combi Inverter/ external AC power source is disconnected, the TM Chargers from Heart Interface. These units transfer switch allows automatic switching perform three distinct functions: back to the inverter. 1. DC to AC power inverting. The Freedom Inverter/Charger operates 2. Automatic transfer switching between as a self-contained backup power system, just inverter power and incoming
ページ5に含まれる内容の要旨
THINGS YOU SHOULD KNOW Circuit Breaker Protection Thermostat Controlled Cooling The Freedom Inverter/Charger is Freedom Inverter/Chargers are equipped supplemental breaker protected. The with a thermostatically-controlled fan that cools INVERT/CHARGE breaker on the front of the the unit so it can operate continually at its rated unit protects against sustained inverter/charger output. over current conditions. Inverter Idle Circuit The 30 Ampere AC INPUT circuit breaker This automatic energy sav
ページ6に含まれる内容の要旨
THINGS YOU SHOULD KNOW Temperature Sensitive Charging When the supplied battery temperature sensor is connected to the unit and the batteries, the charge voltage is controlled based on battery temperature. The charger adjusts the charge voltage to the best level, minimizing water loss in wet cell batteries. Charge voltage regulation optimizes the battery life cycle. TSC Sensor Battery Freedom 20D 6 Part No. 90-0123-00 Libertycombi.p65 10/26/98
ページ7に含まれる内容の要旨
OPERATION • Battery type setup. To enter the battery The Freedom Inverter/Charger provides 120 volt AC power from auxiliary DC batteries, type select mode, press and hold the INVERT automatic battery charging and automatic AC switch for five seconds. The status LEDs will change from indicating status information to transfer switching between an external AC indicating battery type. The selection of the source and inverter mode. battery type is made with the Charge switch. External AC Power Turni
ページ8に含まれる内容の要旨
OPERATION STATUS LEDs NOTE: When AC power is available, the Each Status LED performs two functions, default setting for the charger is ON. If the unit providing battery type selection and operation was manually turned OFF and AC power is in- status. terrupted and becomes available again, the charger will return to ON. Status LEDs LOW BATTERY - Red LED INVERT CHARGE TSC REMOTE • When the LED is OFF the battery OVERTEMP OVERLOAD / AGM voltage is normal, between 10.5 and 15.0 LOW BATTERY / GEL 2 CH
ページ9に含まれる内容の要旨
OPERATION LOW BATTERY & OVERTEMP/OVERLOAD - Red LEDs Overtemp • When both LEDs are blinking, an AC backfeed has been detected. A backfeed Low TSC Auxiliary Port Remote Battery occurs when AC power from an external source is connected to the output of the inverter. Inspect wiring for possible input/output wiring error. This condition will damage the unit and must be corrected before further operation. TSC (Temperature Sensitive Charging) This provides for the connection of a sensor to measure bat
ページ10に含まれる内容の要旨
OPTIONAL REMOTE CONTROL PANELS LINK 2000 Remote Control Panel An optional remote control panel is The Link 2000 has the same features as the Link 1000, providing inverter/charger available. The LED bargraphs on the remote control and complete battery state-of-charge control panel shows battery voltage and DC information. It monitors two battery banks. current in both inverter and charger modes. LINK 2000 Easy to see red, yellow and green LEDs show the battery state-of-charge. Power Sharing, char
ページ11に含まれる内容の要旨
BATTERIES Wet cell batteries will give off gas as a natural result of charging and will experience some water loss. It is very important that the electrolyte level be checked frequently and topped off with distilled water when necessary. Follow the battery manufacturer’s recommendations for maintenance. Never allow the top of the battery plates to be exposed to air, as contamination of the cell will result. Keep the top of batteries clean. Always provide adequate ventilation for the battery stor
ページ12に含まれる内容の要旨
BATTERIES Beware of so-called maintenance-free Series batteries. These batteries have calcium Connecting two batteries in series will alloyed with the lead and hold the liquid double the voltage of the battery bank. For electrolyte in a sponge-like material. They are instance, two 6 volt batteries connected in sealed and water can not be added. Do not series will produce 12 volts. The Amp-hour confuse them with true gel cell or AGM capacity of the battery bank will be the same batteries, they wi
ページ13に含まれる内容の要旨
BATTERIES Parallel Note: It is not advisable to connect Connecting two batteries in parallel will batteries of different case sizes or Amp-hour double the Amp-hour rating of the battery bank, ratings in the same battery bank. while the voltage will be the same as each Always use properly sized wire and individual battery. Example, two 12 volt 105 terminals for your interconnecting battery Amp-hour batteries in parallel will produce one cables. For size information refer to NEC 12 volt 210 Amp-ho
ページ14に含まれる内容の要旨
BATTERIES To achieve 50% cycling you should AMP-HOUR CONSUMPTION FORMULAS calculate your Amp-hour consumption between charging cycles and use a battery (AC Amps x 10) x 1.1 x hours of bank with twice that capacity**. Each AC operation = DC Amp-hours appliance or tool has a rating plate on it and will be rated in either AC Amps or Watts or AC VA (Watts/ DC Voltage) x 1.1 x hours of (Volt-Amps) apparent power. To calculate Amp- operation = DC Amp-hours hour consumption, use one of the formulas to
ページ15に含まれる内容の要旨
BATTERY CHARGING Freedom Battery Chargers Battery Charging Freedom battery chargers are designed Completely charging wet cell deep-cycle to overcome the limitations of conventional batteries requires the battery voltage to be chargers by utilizing 3 distinct charge stages, raised beyond what is known as the gassing each designed for optimal charging of wet, gel point. This is the voltage at which the battery cell and AGM deep-cycle batteries. Battery begins to bubble and gas is given off. If typ
ページ16に含まれる内容の要旨
BATTERY CHARGING NOTE: Freedom battery chargers are ON The battery charger stages are: whenever AC power is connected to the Stage 1 - Bulk Charge During the bulk charger input. The charger can be turned OFF charge stage most of the energy that has been using the CHARGE switch on the front of the consumed during discharge is returned to the unit. This sequence will occur each time battery bank. This phase is engaged as soon external AC power is available. The charger as the battery charger i
ページ17に含まれる内容の要旨
BATTERY CHARGING The float charge stage holds the battery Gel cell and Advanced AGM batteries can voltage constant at a preset lower level, where accept a higher rate of charge. Consult the it is safe for long term battery maintenance. manufacturer for specifications. During the float charge stage, the full output Stage 2 - Acceptance Charge The current of the battery charger is available to acceptance stage immediately follows the bulk operate any DC appliances that may be on the charge stage.
ページ18に含まれる内容の要旨
BATTERY CHARGING The equalizing charge is a timed, 8-hour cycle. The cycle can be ended early by inter- rupting the AC power to the charger at any time during the cycle. Equalizing should only be engaged after the batteries have been fully charged by a normal battery charging cycle. During this equalizing stage, the battery voltage will increase to the equalize voltage. This will cause the battery bank to gas profusely and will accomplish the following: 1. Removal of residual sulfate. Each time
ページ19に含まれる内容の要旨
BATTERY CHARGING WARNINGS 1. Do not equalize gel cell batteries. Check remote default settings. 2. Always monitor the equalize charge cycle. Provide proper ventilation for battery fumes. Do not allow any sparks during equalizing. If one or more cells begin to overflow, terminate the equalize cycle. 3. Check the battery electrolyte both before and after the equalizing charge. Do not expose the battery plates to air. Leave the battery caps on while equalizing. Top off after equalizing. 4. Remove a
ページ20に含まれる内容の要旨
BATTERY CHARGER VOLTAGE SETTINGS TEMP TYPE 0 TYPE 1 TYPE 2 TYPE 3 Wet Cell Gel 1 * Gel 2 * AGM °F°T CAT CCEPFT LOAAT CCEPFT LOAAT CCEPFT LOAAT CCEP FLOA 12045 915 2. 10 2. 10 3. 10 3. 10 3. 19 3. 19 2. 12. 11046 317 3. 15 2. 10 3. 10 3. 14 4. 19 3. 19 3. 12. 10038 819 3. 17 2. 12 3. 11 3. 15 4. 10 3. 10 4. 13. 90 30 211 4. 18 3. 13 3. 12 3. 16 4. 11 3. 11 4. 13. 80 22 713 4. 10 3. 15 4. 13 3. 17 4. 12 3. 12 4. 13. 70 **24 1 **15 4. 11 3. 16 4. 14 3. 18 4. 13 3. 13 4. 13. 60 16 617 4. 13 3. 18 4.
