ページ1に含まれる内容の要旨
GRASS COLLECTION
SYSTEM
PEC PEC PEC PEC PECO O O O O
PPPPP
DESIGNED FOR:
MODEL 12621209 - 12
GRAVELY 200 SERIES MOWER
OPERATOR’S MANUAL
ASSEMBLY OPERATION MAINTENANCE
MANUAL PART#: Q0316 $4.00 REV: 1
ページ2に含まれる内容の要旨
PECO GRASS COLLECTION SYSTEM TABLE OF CONTENTS SECTION PAGE SECTION PAGE Safety ------------------------------2 2-10 Attaching The Boot To The Mower Deck------9 Safety Alert Symbols----------------------3 2-11 Adjusting The Length Of Hose ------------9 Warranty -----------------------------4 2-12 Attaching The Upper Hose- - - ------------10 I INTRODUCTION AND DESCRIPTION - - ------------5 2-13 Attaching The Lower Hose To The Blower 1-1 Introduction - ------------------------5 Cone - - ----------
ページ3に含まれる内容の要旨
SAFETY WARNING! NEVER operate the unit unless the discharge guard and either the deflector assembly or the vacuum collector adapter are fastened securely in place. WARNING! Do not work around the mower deck boot or the blower area until you are certain that the mower blades and the blower impeller have stopped rotating. WARNING! To avoid serious injury, perform maintenance on the vacuum collector; ONLY AFTER STOPPING THE MOWER’S ENGINE AND WAITING FOR ALL MOVING PARTS TO COME TO A COMPLETE STOP.
ページ4に含まれる内容の要旨
PECO LIMITED WARRANTY FOR NEW PRODUCTS A. WHAT IS WARRANTED? PECO extends the following warranties to the original purchaser of each new PECO consumer product subject to the following limitations: 1. PRODUCT WARRANTY: Any part of any consumer product, which is defective in material or workmanship as delivered to the purchaser will be repaired or replaced, as PECO elects, without charge for parts or labor, if the defect appears within 12 months from the date of delivery of the product to the orig
ページ5に含まれる内容の要旨
SECTION I INTRODUCTION AND DESCRIPTION P#(K1198) and (2) 3/8”-16 flange nuts P#(K1215). Use 1-1 Introduction the existing bolt removed from the mower to fasten the front side of the leg. Repeat this step to fasten the right We are pleased to have you as a PECO customer. Your main frame leg assembly P#(A0514). See Figure 1 for collection system has been designed to give you a low details. maintenance, simple, and effective way to collect the Figure 1 Left Lower Main grass clippings from your mowe
ページ6に含まれる内容の要旨
2-3 Attaching The Lift Handle To The 2-5 Aluminum Grass Container Inlet Aluminum Grass Container Attachment The various parts of the handle assembly P#(A0512) The inlet will need to be attached to the container must be attached to the container frame. Figure 5 shows (Figure 8). Open the container, push the inlet from the the orientation and location of the components. Slide the inside of the container through the hole in the container lift handle into the slot in the handle mount bracket to the
ページ7に含まれる内容の要旨
Figure 5 Figure 8 Aluminum Grass Container Assy. Lift Handle Assy. Handle Grip Handle Mount Bracket Latch Rod Figure 6 Aluminum Grass Container With Handle Attached Figure 7 Latch Hook Mechanism Assembled 7
ページ8に含まれる内容の要旨
Figure 9 Aluminum (1) C0025 (1) B8113 Box Top (1) C0029 Grass Container Screen Screen Support Exploded View (1) C0023 (4) B1668 Box Back & Inlet Clamp Sides (1) C1184 (1) V1054 (1) A0938 (1) A0512 Fill Gage Inlet Box/Door Box Handle Frame (1) J0522 (1) B1730 Handle Grip Handle Mount (1) V1131 Plastic Door (1) J0176 Latch Spring (2) B2526 Linkage Rod (1) B3688 (2) K1422 Upper Door Adjusting Nut Member (1) A0260 Latch Rod (2) K1435 Adjusting Screw (1) K1442 Adjusting Ball Joint (1)C0024 (1) A0738
ページ9に含まれる内容の要旨
2-8 Motor Mount Arm Installation 2-10 Attaching The Boot To The Mower Deck Slide the motor mount arm assembly P#(A0006) (Figure 11) into the outer motor mount tube. Secure the motor Mounting The Boot Hanger mount arm assembly using (1) detent pin P#(J0248). Remove the mower’s deflector shield mount (Figure 13). Figure 11 Place the boot hanger P#(B0117) in-between the deflector shield mount and the mower deck. Fasten by using (3) 3/8”-16 x 1-1/4” HHCS P#(K1192) and the existing 3/8” nuts. The boo
ページ10に含まれる内容の要旨
2-11 Adjusting Of The Length Of 2-14 Attachment Of The Lower Hose Hose To The Boot The hoses in steps 2-12 and 2-13 must be cut to fit your Take the unattached end of the lower hose and slide it machine. Follow steps 2-12 and 2-13. Do not cut the over the circular end of the boot. Use the lower hose hoses until you have tried to fit them on your machine. clamp to secure the hose to the boot (Figure 14). Tip: Remember that the hoses have to be long enough to Before securing clamp rotate hose coun
ページ11に含まれる内容の要旨
A. Stop the forward movement of the mower. SECTION III B. Disengage the mower deck. C. Using the throttle cable slow the engine down to idle. OPERATING INSTRUCTIONS D. Push the dump handle, on the left of the operator, away from the unit. While holding the handle pushed 3-1 General Safety away, move the handle upward. The container door will swing upward and the container will rotate downward. The container will release its contents. Only qualified people familiar with this operator’s manual and
ページ12に含まれる内容の要旨
SECTION V PARTS AND SERVICE 5-1 Parts And Service Information PECO collection system owners should record the name and telephone number of their Service Center. Your Service Center will be happy to supply replacement parts, accessories, and do any service or repairs to your collection system. If for any reason your Service Center is unable to service your collection system or supply replacement parts, contact PECO and include the following information on the chart below. THE SERIAL NUMBER PLATE
ページ13に含まれる内容の要旨
13
ページ14に含まれる内容の要旨
NOTES 14
ページ15に含まれる内容の要旨
NOTES 15
ページ16に含まれる内容の要旨
PEC PEC PEC PEC PECO O O O O PPPPP P.O. BOX 1197 ARDEN, NORTH CAROLINA 28704 (800) 438-5823 OR (828) 684-1234 FAX: (828) 684-0858 EMAIL: pecoinc1@bellsouth.net WEBSITE: www.lawnvac.com
