ページ1に含まれる内容の要旨
44” Roller Bar Mower Kit
Installation
Part No. 1687077
For Conquest / 1700 / 2700 / YT / Broadmoor / 1600 / 2600 / LT
Instructions
6
1
9
2
6
9
6
3
9
4
6
5
9
19
6
9
7
8
6
9
7
6
9
6
6
10
8
16
18
12
13
15
13
14
11
17
2
Figure 1. Kit Contents: 1687077
Ref Part No. Qty. Description
11 1931352 1 CARRIAGE BOLT, 3/8-16 x 1-1/2
1 1716159A 1 ROLLER BAR, 44 Mower
12 1731383A 2 CAPSCREW, Hex, 5/16-18 x 1-1/2
2 2860681 2 LOCKNUT, Top Lock, 3/8-16
13 1919381 4 WASHER, 5/16
3 1677507 1 SLIDE
14 1731384 2 LO
ページ2に含まれる内容の要旨
Installation Instructions Roller Bar Mower Kit K A E I F X D U Y J V X E C B G Q A L M N D Z D D O P F R T S W H Figure 2. Remove Frame Hung I. Crank & Trunnion Assembly S. Adjustment Rod Components J. Capscrews, 5/16-18 x 1-1/4 T. Rocker Arm Assembly A. Capscrews, 5/16-18 x 1-1/4 K. Arm U. Washer, 3/8, Small B. Washer, 5/16 L. Height of Cut Plate V. Strap C. Indicator M. Lockwasher, 5/16 W. Locknut, 3/8-16 D. Capscrews & Locknuts N. Nut, 5/16-18 X. Chains, 3 Link E. Hangers O. Hair Pin Y. Upst
ページ3に含まれる内容の要旨
Roller Bar Mower Kit Installation Instructions O E P U B V F B C A Q W X B G S T D Y B W H I U Z R B V J A K N M L Q Figure 3. Installation 44” Rollers I. Nut & Lockwasher R. Carriage Bolt, 3/8-16 x 1-1/2 A. Capscrews, 5/16-18 x 1-1/4 J. Hair Pin S. Washer, Small, 5/16 B. Washer, Large, 5/16 K. Clevis Pin T. Upstop C. Indicator L. Adjustment Rod U. Capscrew, 5/16-18 x 1-1/2 D. Mower Support Plate M. Rocker Arm Assembly V. Chain, 2 Link E. Crank & Trunnion Assembly N. Straps W. Locknut, 5/16-18
ページ4に含まれる内容の要旨
Installation Instructions Roller Bar Mower Kit MOWER DECK REMOVAL & A INSTALLATION C Chain Lift Models B D WARNING Figure 4. Mower Lift A. Lift Hook C. PTO Belt Engage parking brake, disengage PTO, stop B. Lift Chain D. Idler Arm engine and remove key before attempting to install or remove the mower. Muffler and surrounding areas may be hot. Removing the Mower Deck 1. Park the tractor, fully lower the attachment lift, turn off the PTO, turn off the engine, remove the key, and engage the parking
ページ5に含まれる内容の要旨
Roller Bar Mower Kit Installation Instructions Installing the Mower Deck NOTE: Perform mower installation on a hard, level sur- face such as a concrete floor. A 1. Park the tractor, fully lower the attachment lift, turn off the PTO switch, turn off the engine, remove the key, and engage the parking brake. Turn the wheels fully to the left. 2. Place mower in the lowest cutting position using the mower height adjuster. Slide the mower deck under B the right side of tractor so that the mower hitch
ページ6に含まれる内容の要旨
Installation Instructions Roller Bar Mower Kit Leveling The Mower If the cut is uneven, the mower may need leveling. Unequal or improper tire pressure may also cause an uneven cut. Make sure tire pressure is correct as speci- A fied in Checking Tire Pressure. SIDE-TO-SIDE LEVELING 1. With the mower installed, place the tractor on a B smooth, level surface such as a concrete floor. Turn the front wheels straight forward. 2. Check for bent blades and replace if necessary. 3. Place the mower in mid
