ページ1に含まれる内容の要旨
Viper
u s e r ` s g u i d e
AMERICAN
TECHNOLOGIES
NETWORK
CORP.
ページ2に含まれる内容の要旨
One 3 volt battery Builtin infra-red illuminator Camera 5 Diopter adapter 35mm F 1:1.4 lens for maximum clarity Optional focal length doubler gives the Viper increased magnification, in just seconds, without any tools. Master power 1’ to Infinity focus FEATURES • Great for hunting, camping, boating or surveillance • Total darkness technology • Automatic brightness control • Built-in IR illuminator • Manual focus • Adjustable eyepiece • High res. 1st Gen+ intensifier tube • Rugged
ページ3に含まれる内容の要旨
APPLICATION The Viper Night Vision Scope is a complex opticoelectronic system for individual use. The device consists of (see above figure) the objective lens assembly, eyepiece and the body. The body contains a 1st Gen.+ image intensifier tube assembly with an integrated high voltage power source and the three volt battery housing. When installing the battery one should keep in mind that the polarity of the battery should coincide with the diagram on the body next to the battery housing c
ページ4に含まれる内容の要旨
INFRA-RED ILLUMINATOR Infra-red illuminators, or IR illuminators, are common to night vision. The IR light greatly enhances the performance of the Viper while remaining almost totally invisible to the naked eye. The IR illuminator on the Viper is located underneath the front lens, next to the battery compartment. When you turn the scope on the IR will automatically turn on. It is impor- tant to remember that the IR illuminator is simply an infra red light source, and like any light source,
ページ5に含まれる内容の要旨
• You may need to focus the 35mm camera or video camera in combination with the Viper in order to get the sharpest possible image. • We suggest that you find an open space to work in. Focus the Viper so that the scene is at its sharpest. For best results you should disable the auto focus (if any) on either the 35mm camera or the video camera and manually focus the 35mm camera or the video camera. Once the image is sharp, then simply adjust the Viper’s front lens to change the focus. • An im
ページ6に含まれる内容の要旨
CLEANING THE EYEPIECE You may need to clean the eyepiece of the Viper from time to time in order to guarantee top performance. When you receive your Viper you should check for dust on the eyepiece of the unit. First you will need to remove the eyepiece. To do that you will need to initially loosen the 2 set screws that can be found on the base. Then unscrew the eyepiece counter-clockwise to remove it. NOTE: You do not have to remove the set screws completely, they are very small and easy to
ページ7に含まれる内容の要旨
2 YEAR PRODUCT WARRANTY This product is guaranteed to be free from manufacturing defects in material and workmanship under normal use for a period of 2 (two) years from the date of purchase. In the event a defect that is covered by the foregoing warranty occurs during the applicable period stated above, ATN, at its option, will either repair or replace the product, and such action on the part of ATN shall be the full extent of ATN’s liability, and the Customer’s sole and exclusive remedy.
ページ8に含まれる内容の要旨
For customer service and technical support, please contact American Technologies Network Corp. North American Office 20 S. Linden Ave. Suite 1B, South San Francisco, CA 94080 phone: 800-910-2862, 650-875-0130; fax: 650-875-0129 European Office phone: 44(0)870-0111286, fax: 44(0) 845-3349142 The following countries can use our toll free number 00 800 9102-8620 Austria, France, Germany, Holland, Italy, Spain, Sweden, Switzerland www.atncorp.com ©2001 ATN Corporation
