ページ1に含まれる内容の要旨
®
MultiModem ISI
ISI9234HPCIE Server Card User Guide
ページ2に含まれる内容の要旨
MULTIMODEM®ISISERVERCARDUSERGUIDE ® MultiModem ISIServerCardUserGuide Model: ISI9234HPCIE Part Number: S000581, Version 1.1.3 Copyright This publication may not be reproduced, in whole or in part, without the specific and express prior written permission signed by an executive officer of Multi-Tech Systems, Inc. All rights reserved. Copyright©2014byMulti-TechSystems,Inc. Multi-Tech Systems, Inc. makes no representations or warranties, whether express, implied or by estoppels, with respect to the
ページ3に含まれる内容の要旨
CONTENTS Contents ProductOverview....................................................................................................................................................5 Product Overview.......................................................................................................................................................... 5 ISI Server Cards................................................................................................................................
ページ4に含まれる内容の要旨
CONTENTS EnvironmentalInformation.................................................................................................................................... 24 Waste Electrical and Electronic Equipment Statement.............................................................................................. 24 WEEE Directive.......................................................................................................................................................... 24 Instructio
ページ5に含まれる内容の要旨
PRODUCTOVERVIEW ProductOverview ProductOverview The MultiModem ISI server cards and modems provide four built-in V.92/56K modems on an industry-standard PCI Express x1 architecture for analog dial-up or dedicated fax servers. It also offers V.34/33.6K Super G3 fax and Error Correction Mode to reduce fax transmission time. ISIServerCards The ISI9234HPCIE is a server modem expansion card that uses the PCI Express x1 architecture with four V.92 data/Super G3 fax modems. It allows you to add modems
ページ6に含まれる内容の要旨
PRODUCTOVERVIEW Documentation Download documentation from www.multitech.com/setup/product.go. MultiModem ISI ISI9234HPCIE User Guide This document. Provides specifications, safety and regulatory information, installation, and configuration information (part number S000581). MultiModem and SocketModem MT9234 AT Provides AT commands for configuring your device (part Command Reference Guide number S000434). Fax Overview Developer Guide Describes fax protocols, formats, compression, and transmission
ページ7に含まれる内容の要旨
PRODUCTOVERVIEW Specifications Category Description General Bus Type PCI Express form factor 1x, PCIe 1.0 compatible. Interrupt Request One IRQ per card (can be shared) Speed Baud Rates 300 bps to 230 Kbps per port PhysicalDescription Weight 0.45 lbs. (200 g) Dimensions See the topic, Dimensions. ConnectorsandCables Connectors One RJ-45 jack Cables One RJ-45 4-port fan-out cable Environment 1 Operating Temperature 23° to 140° F (-5° to 60° C) PowerRequirements Input Voltage 3.3V from PCIe interf
ページ8に含まれる内容の要旨
PRODUCTOVERVIEW Dimensions DimensionswithStandardBracket ® 8 MultiModem ISI ISI9234HPCIE Server Card User Guide
ページ9に含まれる内容の要旨
PRODUCTOVERVIEW DimensionswithLowProfileBracket PowerMeasurements Sleep Typical Maximum Peak TotalInrush TotalInrush Charge Charge measuredin Duration Millicoulombs during (mC) Powerup 3.3volts Current (AMPS) 0.402 0.541 0.550 0.592 16.00 26mS Watts 1.320 1.760 1.790 ® MultiModem ISI ISI9234HPCIE Server Card User Guide 9
ページ10に含まれる内容の要旨
SAFETYNOTICES SafetyNotices AnalogTelecomSafetyWarnings Before servicing, disconnect this product from its power source and telephone network. Also: ■ Never install telephone wiring during a lightning storm. ■ Never install a telephone jack in wet locations unless the jack is specifically designed for wet locations. ■ Use this product with UL and cUL listed computers only. ■ Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interf
ページ11に含まれる内容の要旨
INSTALLINGHARDWARE InstallingHardware ChangingMountingBrackets To use the low profile bracket, remove the standard bracket and replace it with the low profile bracket. Warning: Before handling the device, discharge any static in your body by touching a piece of grounded metal such as the computer chassis. Electrostatic discharge (ESD) is the release of stored static electricity that can damage electrical circuitry or components. Static electricity is often stored in your body and discharged when
ページ12に含まれる内容の要旨
INSTALLINGHARDWARE 2. Remove the two screws holding the standard bracket to the device. ® 12 MultiModem ISI ISI9234HPCIE Server Card User Guide
ページ13に含まれる内容の要旨
INSTALLINGHARDWARE 3. Mount the low profile bracket using the screws you removed in Step 1. InstallingHardware Note: Install the hardware, before installing drivers. Warning: Before handling the device, discharge any static in your body by touching a piece of grounded metal such as the computer chassis. Electrostatic discharge (ESD) is the release of stored static electricity that can damage electrical circuitry or components. Static electricity is often stored in your body and discharged when y
ページ14に含まれる内容の要旨
INSTALLINGHARDWARE Attention: Perform the procedure described in this section only at an ESD workstation using an antistatic wrist strap. If such a station is not available, you can provide some ESD protection by wearing an antistatic wrist strap and attaching it to a metal ground screw (lug). To install the ISI card in your PCI-bus computer: 1. Turn off your computer, remove the power cord, and disconnect any peripheral devices. 2. Remove the computer's cover as instructed in your computer's ma
ページ15に含まれる内容の要旨
INSTALLINGHARDWARE CableDiagrams The ISI9234HPCIE uses a single fan-out cable to connect the four modems to four phone lines. The cable has an RJ- 45 connector on one end and four RJ-11 connectors on the other end. Use the RJ-11 connectors to connect to phone lines. ® MultiModem ISI ISI9234HPCIE Server Card User Guide 15
ページ16に含まれる内容の要旨
INSTALLINGONWINDOWS InstallingonWindows The ISI9234HPCIE supports both 32-bit and 64-bit versions of the following Windows operating systems: ■ Windows Server 2003, 2008, and 2012 ■ Windows 7, 8, Vista, and XP For Linux support, refer to Installing on Linux. DownloadingWindowsDrivers Note: Drivers for all supported Windows operating systems are included in the same zip file. To select the correct driver, you need to know if you have a 32-bit or 64-bit operating system. If you do not know, check
ページ17に含まれる内容の要旨
INSTALLINGONWINDOWS To get the Communications port numbers to match COM ports: 1. In the Device Manager, go toModems. 2. Right-clickMultiTechSystemsMT9234SMI#4 and selectUninstall. 3. On the Confirm Device Uninstall tab, check Deletethedriversoftwareforthisdevice. ,if provided, and selectOK. 4. Repeat the uninstall for the remaining three modems. 5. In Device Manager go toPorts. 6. Right-clickMultiTechCommunicationsPort(COMx) and selectUninstall. 7. On the Confirm Device Uninstall tab, check Del
ページ18に含まれる内容の要旨
INSTALLINGONLINUX InstallingonLinux InstallingonLinuxKernel3.5andHigher Note: The steps below were tested with Ubuntu 12.04 with Linux kernel 3.5.0 and may or may not work for other 3.x.x versions. After installing the ISI9234HPCIE in a PCIe slot: 1. Power up the computer and boot to Linux. 2. Go to www.multitech.com/setup/product.go and select your model from the Product drop down list. 3. Download the Linux driver,xr17v35x-lnx3.x.x-pak.zip, into a specified directory, such as /exar. 4. Start a
ページ19に含まれる内容の要旨
INSTALLINGONLINUX 11. Run the commanddepmod. 12. Reboot Linux. Linux device drivers and device should now be installed and activated. To verify that the modules loaded, send the command lsmod ® MultiModem ISI ISI9234HPCIE Server Card User Guide 19
ページ20に含まれる内容の要旨
CONFIGURINGMODEMSFORYOURCOUNTRY ConfiguringModemsforYourCountry Different countries have different regulations for modem operation. Before using your modems, you must configure them for the country in which you are using them. For Windows computers, use the Global Wizard to set the country. For Linux computers, use AT Commands to set the country. InstallingtheGlobalWizard The Global Wizard utility works with the 32-bit and 64-bit versions of following Windows operating systems: ■ Windows Server
