ページ1に含まれる内容の要旨
Featuring
ページ2に含まれる内容の要旨
INTRODUCTION Thank you for purchasing a Monitor 2 mixer, brought to you with pride by the SPIRIT team of Andy, Colin, Chris, James, Simon, Mukesh, Graham, Martin, Paul, Tony and Peter, with the support of many others - we hope you will have as much fun using it as we did building it! SAFETY PRECAUTIONS The SPIRIT MONITOR 2 mixer must only be connected For your own safety and to through the Power Supply supplied. avoid invalidation of the warranty please read this section carefully. The wires
ページ3に含まれる内容の要旨
Connecting Up 24 INPUTS Page 3
ページ4に含まれる内容の要旨
100Hz HI-PASS FILTER USING MONITOR 2 Pressing this switch activates a steep 18dB per octave filter which reduces the level of bass frequencies only. Use this in live PA situations to clean up Mono Input Channel 1 the mix, reducing stage rumble or popping from microphones. XLR Input INSERT POINT The UltraMic Plus padless input preamp is designed to accept BALANCED or The unbalanced, pre-EQ insert point is a break in the channel signal path, UNBALANCED signals at a wide range of input levels up
ページ5に含まれる内容の要旨
MONITOR SENDS 7 These controls route the input channel signal to any one or more Monitor busses and the associated Monitor Outputs, allowing a number of unique monitor mixes to be created. The sends are arranged as a group of mono sends (1-8) and two stereo pairs (9/10 & 11/12). Each group of sends is normally POST-FADE, POST-EQ but may be switched to PRE-FADE, POST-EQ by pressing the corresponding PRE switch. All sends are muted when the MUTE switch (9) is pressed. Sends 9-12 are arranged
ページ6に含まれる内容の要旨
FOH Facility OUTPUT SECTION A sub-grouping facility is included on outputs 1-10 to allow the console to be used as a FOH mixer. Pressing the 11-12 switch MONITOR OUTPUTS routes the post-fade, post-insert signal to the Monitor 11/12 These outputs provide summing of the corresponding input channel busses, enabling these outputs to be used as a stereo final mix. monitor sends, and drive XLR-type output sockets from impedance The PAN control positions the monitor signal in the stereo 11 balanced ou
ページ7に含まれる内容の要旨
FX RETURNS MASTER SECTION Two balanced Stereo Returns are included for the outputs of effects units WEDGE SOURCE and are made available for mixing directly to the Monitor outputs at a level The Engineers Wedge outputs are normally fed from a mix of the MNTR set by the FX1 RET or FX2 RET controls. If a mono source is used, plugging feeds from outputs 1-12. The pre-fade wedge signal feeds the headphones into the Left jack only automatically feeds the signal to both Left and Right. 2 and meters
ページ8に含まれる内容の要旨
l Feed the signal to selected monitor outputs by Setting Up & Troubleshooting Troubleshooting setting the appropriate monitor sends to an initial Hum on outputs when SPLIT OUT sockets are used working level (approx. position 7 on the send No Power Initial Set Up knob). Listen to the signal by feeding the l Check for ground loops, and try isolating the Once you have connected up your system (see the selected monitor signal to the engineers wedge l Is the mains supply present? Check the mains S
ページ9に含まれる内容の要旨
APPLICATIONS Live Monitor with Effects BAND INSTRUMENTS/VOCALS Page 9
ページ10に含まれる内容の要旨
Live Monitor with In-Ear Monitoring BAND INSTRUMENTS/VOCALS Page 10
ページ11に含まれる内容の要旨
Theatre Page 11
ページ12に含まれる内容の要旨
FOH Console Page 12
ページ13に含まれる内容の要旨
FOH Console with Subgrouping Page 13
ページ14に含まれる内容の要旨
System Block Diagram +48V +48V PEAK DETECT INPUT & PFL ON PHASE PFL SENS PEAK 100Hz DETECT SOLO/PFL MIC TRIM INPUT PFL 2 3 PHONES SOLO L 1 PHONES MONITOR EQ SPLIT INSERT SOLO R 2 3 1 MASTER T/B 1 TIP: SEND RING: RETURN MASTER SPLIT OUTPUT WEDGE/SOLO (Internal Link) DIM 2 SOLO L METER L Link - Grounded No Link - Ground Lift SIG MNTR WEDGE 3 SIGNAL SOURCE 11-12 WEDGE DETECT WEDGE L 3 4 DIM 1 2 MUTE 5 WEDGE 6 R 3 DIM 2 1 1-8 7 PRE PFL/SOLO SOLO R 8 ENABLE INPUT WEDGE/SOLO FADER METER R 9 9-10
ページ15に含まれる内容の要旨
Connecting Leads ’Y’ Leads (Balanced) Balanced Unbalanced Headphone Splitter ’Y’ Leads (Unbalanced) Insert Leads Lamp Connections Page 15
ページ16に含まれる内容の要旨
Control Position Sheet You may freely copy this page to mark control positions to assist in resetting the desk between performances.
ページ17に含まれる内容の要旨
INPUTS MONITOR 2 CONSOLE Typical Starting Out Control Positions Page 17
ページ18に含まれる内容の要旨
Dimensions 87.5 mm Specifications (3.44") dim. ’x’ Noise Measured RMS, 22Hz to 22kHz Bandwidth. Inputs at unity gain and terminated 150W Output Noise 24 inputs routed, sends down, master @ unity < -80dBu EIN dim. ’y’ Mic EIN @ max. gain (150Wterminated) -129dBu THD+N Width without end trim Mic sens. -10dBu, Faders @ unity, send at max., (for flight case mounting) +20dBu at all outputs @ 1kHz <0.005% Crosstalk (@1kHz) Typical Channel send range >90dB Console dim ’x’ dim ’y’ Channel fader
ページ19に含まれる内容の要旨
A Harman International Company Part No: ZM0192
