ページ1に含まれる内容の要旨
802.11a/b/g SDIO
WiFi Module
User Manual
1
ページ2に含まれる内容の要旨
Table of Contents INTRODUCTION ..............................................................................................5 FEATURES.........................................................................................................5 INSTALL THE DRIVER...................................................................................7 ACCESS THE WLAN UTILITY ......................................................................7 CONFIGURE WIRELESS NETWORKS...........................
ページ3に含まれる内容の要旨
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio com
ページ4に含まれる内容の要旨
IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. IMPORTANT NOTE: This module is intended for OEM integrator. The OEM integrator is still responsible for the FCC compliance requirement of the end product, which integrates this module. 20cm minimum distance has to b
ページ5に含まれる内容の要旨
INTRODUCTION An IEEE 802.11a/b/g SDIO WiFi Module work for various applications. The 802.11a/b/g SDIO WiFi Module is a compact size wireless module for cellular handset and consumer electronic devices that require low power consumption. The module works with a lot of wireless LAN security protocols. Open, 64-bit and 128-bit WEP encryptions are supported. FEATURES Module size as 20 x 20 x 3.0 mm. Host interface support for SDIO. Supports the IEEE802.11 wireless. High radio per
ページ6に含まれる内容の要旨
The Peer-to-Peer workgroup configuration enables you to quickly set up a small wireless workgroup, where the workgroup participants can exchange files using features like “Files and Printer Sharing” as supported by Microsoft®Networking. You can use this option to setup a temporary or Ad-hoc network in environments where no access points are available (for example in Small Office/Home Office “SOHO” environments). As long as the stations are within range of one another, this is the easiest
ページ7に含まれる内容の要旨
INSTALL THE DRIVER Install the SD WLAN Module Driver into the PDA that using Microsoft WinCE 5.0 or higher. Note: Do not insert the SD WLAN Module into the SD slot of your PDA until the Driver installation has been performed completely. 1. Install the driver into the PDA, double click the file to start the driver installation, then it will install automatically. 2. After the installation process finished, go to Start > Program > Setup > System > Remove programs to confirm the driver
ページ8に含まれる内容の要旨
CONFIGURE WIRELESS NETWORKS Select an available AP or router from the list then tap to make a connection. Wireless tab Wireless Networks Select an available AP or router from the list then tap to make a connection. Networks to access Select the type of network access from the pull-down list. All available: A group of wireless devices communicating with both access points and network adapters. Only access points: A group of wireless devices communicating directly with only access po
ページ9に含まれる内容の要旨
Network Adapters tab My network card Tap Work or The Internet from the pull-down menu. connects to Work: Connects to the network in your office. The Internet: Connects to your ISP at home. Tap an adapter from the list to enter its configuration Tap an adapter to modify settings screen. If AR6000 SDIO WLAN Adapter is tapped, the following screen will appear for you to configure: IP Address tab 9
ページ10に含まれる内容の要旨
Use server-assigned IP address To use DHCP (Obtain IP address automatically), select Use server- assigned IP address. The Wireless Router will act as a DHCP server. An IP Address will be obtained from the Wireless Router automatically. Use specific IP address IP Address: Enter the IP address (within the range of the wireless router’s IP address, for instance, if the IP address of the router which you wish to connect is 192.168.1.254, you may enter the IP 10
ページ11に含まれる内容の要旨
address here from 192.168.1.1 to 192.168.1.253 ). For example: 192.168.1.199. Subnet mask: The Subnet Mask must be the same as that set on your Ethernet network. For example: 255.255.255.0 Default Gateway: Enter the IP address of your network’s gateway. The gateway is the device that enables communication between your computers and the Internet. In most cases, your router acts as your gateway. For example: 192.168.1.254 Name Servers tab DNS Enter the IP address of your ISP' s ser
ページ12に含まれる内容の要旨
Cannot Connect To Network If your SD WLAN Module seems to be working fine, but you are not able to connect to the network, this error might be due to a configuration mismatch. For example the problem is likely to be caused by a configuration mismatch of: - Network Name (The SD WLAN Module Network Name (SSID) is case-sensitive). - Encryption Key of the AP that you try to make a connection. Other causes may be: - No driver loaded. - Station not authorized to access network. - SD WLAN Modu
ページ13に含まれる内容の要旨
SPECIFICATIONS
! ! "
# $ %
& & ' ( )"* + ,
- . / 0& . 1 0".
+ ,
- . / 0& . 1 0". # 2 . 03 3 "-
% 4 #
ページ14に含まれる内容の要旨
E D ,
- < ) . "6
1 * +
%
% ) . "6
1 * + )! .
1 * + !
# = 22
; > , @ $ .
0= > < = D > < & = 4 > . .
% / . - 0)"B .
