ページ1に含まれる内容の要旨
TL-WN881ND
300Mbps Wireless N PCI Express Adapter
Rev: 1.0.0
1910010532
ページ2に含まれる内容の要旨
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2011 TP-LINK TECHNOLOGIES CO.,
ページ3に含まれる内容の要旨
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
ページ4に含まれる内容の要旨
CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. National Restrictions 2400.0-2483.5 MHz Country Restriction Reason/remark General authorization required for outdoor use and Bulgaria public service Outdoor use limited to 10 mW Military Radiolocation use. Refarming of the 2.4 GHz France e.i.r.p. within the band band has been ongoing in recent years to allo
ページ5に含まれる内容の要旨
TP-LINK TECHNOLOGIES CO., LTD DECLARATION OF CONFORMITY For the following equipment: Product Description: 300Mbps Wireless N PCI Express Adapter Model No.: TL-WN881ND Trademark: TP-LINK We declare under our own responsibility that the above products satisfy all the technical regulations applicable to the product within the scope of Council Directives: Directives 1999/5/EC The above product is in conformity with the following standards or other normative documents: ETSI EN 300
ページ6に含まれる内容の要旨
CONTENTS Package Contents .................................................................................................... 1 Chapter 1 Introduction ........................................................................................ 2 1.1 Product Overview...................................................................................................... 2 1.2 Features .................................................................................................................
ページ7に含まれる内容の要旨
Package Contents Please verify that all the package contents below are available. One TL-WN881ND 300Mbps Wireless N PCI Express Adapter Quick Installation Guide One Resource CD for TL-WN881ND, including: • TP-LINK Wireless Configuration Utility (TWCU) and Drivers • User Guide • Other helpful information Note: Make sure that the above items are contained in the package. If any of the above items are damaged or missing, please contact your distributor. Conventions The ‘adapter’
ページ8に含まれる内容の要旨
TL-WN881ND 300Mbps Wireless N PCI Express Adapter User Guide Chapter 1 Introduction 1.1 Product Overview The adapter is an 802.11n client device designed to deliver a high-speed and unrivaled wireless performance for your desktop. With a faster wireless connection, you can get a better Internet experience, such as downloading, gaming, video streaming. With the 802.11n technology, higher throughput improvements using MIMO (multiple input, multiple output antennas), the TL-WN881ND’s auto-s
ページ9に含まれる内容の要旨
TL-WN881ND 300Mbps Wireless N PCI Express Adapter User Guide 1.3 Hardware Overview LED status: Status Working Status The driver has not been installed; Off The adapter's radio has been disabled. The driver has been installed but no data is being transmitted or Flashing Slowly received. Flashing Quickly Data is being transmitted or received. 3
ページ10に含まれる内容の要旨
TL-WN881ND 300Mbps Wireless N PCI Express Adapter User Guide Chapter 2 Installation Please install the PCI Express adapter into your computer before installing the driver software from the Resource CD. 2.1 Hardware Installation 1. Turn off your computer and unplug the power cord from the computer. 2. Open the case and locate an available PCI Express slot. Remove the metal slot cover on the back of the PC. Keep the screws. Turn to your computer manufacturer for instructions if needed.
ページ11に含まれる内容の要旨
TL-WN881ND 300Mbps Wireless N PCI Express Adapter User Guide 2. The InstallShield Wizard window will appear. Click Next to continue. Figure 2-2 3. Choose a setup type. It is recommended to select Install TP-LINK Wireless Configuration Utility and Driver. Selecting Install Driver Only will only install driver. Click Next to continue. Figure 2-3 5
ページ12に含まれる内容の要旨
TL-WN881ND 300Mbps Wireless N PCI Express Adapter User Guide 4. Click Change to specify the destination location for the software or you can leave it default. Click Next in the screen below to continue. Figure 2-4 5. Click Install to continue the setup. Figure 2-5 6
ページ13に含まれる内容の要旨
TL-WN881ND 300Mbps Wireless N PCI Express Adapter User Guide 6. The utility and drivers will install. This may take 1~2 minutes. Figure 2-6 7. After all the steps above, you will see the screen below. Click Finish to complete the setup. Figure 2-7 7
ページ14に含まれる内容の要旨
TL-WN881ND 300Mbps Wireless N PCI Express Adapter User Guide 8. After installation, the utility configuration page will automatically pop up as shown in the following figure and the icon will appear in your system tray. To connect to a network, please refer to Chapter 3 Connect to a Wireless Network. Figure 2-8 8
ページ15に含まれる内容の要旨
TL-WN881ND 300Mbps Wireless N PCI Express Adapter User Guide Chapter 3 Connect to a Wireless Network With both the hardware and software successfully installed into your computer, you can quickly connect to a wireless network using one of the following methods. Method One: To connect using TWCU TL-WN881ND uses the TP-LINK Wireless Configuration Utility as the management software. The utility provides you an easy interface to connect to a network and to change any settings related to th
ページ16に含まれる内容の要旨
TL-WN881ND 300Mbps Wireless N PCI Express Adapter User Guide SSID (Service Set Identifier) is the name of the wireless network. The adapter will automatically connect to your target network next time if you tick Connect automatically. Figure 3-2 3. If word None appears behind the SSID, this means the network to be connected is not security-enabled and you can connect to the network without entering a key. To prevent outside intrusion and safeguard your network, it is strongly recommende
ページ17に含まれる内容の要旨
TL-WN881ND 300Mbps Wireless N PCI Express Adapter User Guide Input the password which can be found on the configuration page of your router or access point, then click OK to continue. Or push the QSS/WPS button on your router if your router features the QSS/WPS function to quickly build a connection without having to enter a key. Figure 3-4 4. You have now successfully connected to your network. Click Close to enjoy the Internet. Figure 3-5 5. To view more information about the netw
ページ18に含まれる内容の要旨
TL-WN881ND 300Mbps Wireless N PCI Express Adapter User Guide Figure 3-6 3.2 To connect using QSS QSS (Quick Secure Setup) function allows you to add a new wireless device to an existing network quickly. If the wireless router supports QSS or Wi-Fi Protected Setup (WPS), you can establish a wireless connection between wireless card and router using either Push Button Configuration (PBC) method or PIN method. Three QSS connection methods are listed in the following parts while the third
ページ19に含まれる内容の要旨
TL-WN881ND 300Mbps Wireless N PCI Express Adapter User Guide Figure 3-7 3. The adapter will be connecting to the target network. Figure 3-8 13
ページ20に含まれる内容の要旨
TL-WN881ND 300Mbps Wireless N PCI Express Adapter User Guide 4. When the following window appears, you have successfully connected to the network. Figure 3-9 3.2.2 PIN method There are two ways to configure the QSS by PIN method: 1) Enter the PIN from your AP device. 2) Enter a PIN into your AP device. Following are detailed configuration procedures of each way. 3.2.2.1. Enter the PIN from your AP device 1. Open TWCU and click QSS tab. Select Enter the PIN of my access point or wir
