ページ1に含まれる内容の要旨
USB ADSL Modem
USB ADSL Modem
Quick Installation Guide
Quick Installation Guide
M73-APO02-560
ページ2に含まれる内容の要旨
REGULATORY STATEMENTS Part15, Class B This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interface, and 2. This device must accept any interface received, including interface that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protecti
ページ3に含まれる内容の要旨
Table of Contents HARDWARE INSTALLATION ........................ 1 SOFTWARE INSTALLATION ......................... 2 Windows 98/98SE/ME................................ 2 Windows 2000/XP ...................................... 4 PPPOE and PPPOA Configuration........... 10
ページ4に含まれる内容の要旨
HARDWARE INSTALLATION Precaution Precaution Before the installation, make sure the USB port exists in your computer and is enabled. Go to My Computer Control Panel System. Open the Device Manager tab, check if the Universal Serial Bus controller device is found. 1. You can connect this modem without powering down your PC. 2. Connect the USB connector on the modem to the USB port of your PC. 3. Connect the phone line to the phone jack on your modem. 4. Windows will detect the ne
ページ5に含まれる内容の要旨
SOFTWARE INSTALLATION As you perform the installation, have your Windows disk at hand. You may need this disk to refresh or replace some Windows software. Also, make sure you have the existing Telephone Network Service and an ISP (Internet Service Provider) offered you ADSL service. After the device has been connected to your computer, Windows will detect the new hardware automatically. Windows 98/98SE/ME Windows 98/98SE/ME 1. For Windows 98/98SE applications, in Add New Hardware Wiz
ページ6に含まれる内容の要旨
5. Click Next. 6. Insert the Windows 98/98SE CD, and then click OK. 7. Click Finish. - 3 -
ページ7に含まれる内容の要旨
8. Click Yes to restart your computer. 9. At the Welcome screen, click Next. 10. Please refer to step 7 ~ step 13 in Windows 2000/XP section to continue the installation. Windows 2000/XP Windows 2000/XP 1. For Windows 2000 applications, click Next. - 4 -
ページ8に含まれる内容の要旨
2. For Windows 2000 applications, select Recommended option, then click Next. For Windows XP applications, select Advanced option, then click Next. 3. Insert the supplied CD into the CD-ROM drive. Select CD-ROM then click Next. 4. For Windows 2000 applications, in “Driver Files Search Results”, click Next. 5. The window may display a warning message, just ignore this message and click Yes (In Windows 2000) /Continue Anyway (In Windows XP) to complete the installation. - 5 -
ページ9に含まれる内容の要旨
6. At the Welcome screen, click Next. 7. In “License Agreement”, click Yes. 8. In “Read Me”, click Next. - 6 -
ページ10に含まれる内容の要旨
9. In “Driver Components”, follow your Internet Service Provider (ISP) instructions to select the appropriate driver type from RFC1483, PPPoA, or PPPoE. You may also see an option to change the VPI/VCI settings. Then click Next.. RFC1483 10. Select the appropriate framing setting given by your Internet Service Provider (ISP). This could be either LLC or VCMUX/NULL. Click Next. - 7 -
ページ11に含まれる内容の要旨
11. This step is only for users who select RFC1483 in step 9: Follow your Internet Service Provider (ISP) instructions to select from Bridged or Routed. If the ISP did not mention about it, select Bridged. Then click Next. In ”IP Configuration“, refer to the information provided by your Internet Service Provider (ISP) then click Next. - 8 -
ページ12に含まれる内容の要旨
12. Click Finish. 13. In “Rebooting Machine”, select Yes, I want to restart my computer now. Click OK to restart the computer. 14. For Windows XP applications, click Continue Anyway to complete the installation. - 9 -
ページ13に含まれる内容の要旨
P PP PP PO OE E a an nd d P PP PP PO OA A C Co on nf fiig gu ur ra at tiio on n After you have installed the appropriate driver, follow below steps to configure the connection. 1. Click either the desktop icon, or the Dial-Up Networking icon to open the Connect To window. 2. Provide the following information: 1. Supply the User Name. 2. Supply the Password. 3. Click the field for Save Password, if you want the system to remember the password. 4. Click Dial to set up the connectio
