ページ1に含まれる内容の要旨
```
Quick Installation Guide
Wireless N 3G / 3.5G Mobile Router
Model # AR660W3G
Ver. 1A
ページ2に含まれる内容の要旨
Introduction Congratulations on your purchase of AR660W3G Wireless N 3G/3.5G Mobile Router. This product is specifically designed for business travelers or SOHO needs. It provides an extended WAN solution, 3G Mobile USB modem card for Internet surfing besides regular Cable or DSL modem and is easy to share the Internet connectivity wherever 3G mobile Internet service is available. It is recommended to use with AirLink101® Wireless N products to provide the best performance. The hi
ページ3に含まれる内容の要旨
Step 1 Option 1 Plug the 3G/3.5G USB modem card into the USB slot on the front panel of the router. 3G USB Modem Option 2 Connect one end of a network cable to the WAN port of the router and connect the other end of the cable to the DSL/Cable modem. Power on the modem. Cable/DSL Modem Step 2 With another network cable, connect one end of the cable to your computer’s Ethernet port and connect the other end to one of the LAN ports of the router. (After setup finishes, you can
ページ4に含まれる内容の要旨
Step 3 Plug the power adapter to the router and connect it to an outlet or power strip. Step 4 Power on your computer. Step 5 Make sure either WAN or USB, WLAN, and the LAN port that the computer is connected to are lit. If not, try the above steps again. LED Indicators: Light LED Description Status POWER On Router is powered on. On WPS setup is in progress. WLAN Off Wireless network is switched off. Wireless network is ready and WPS setup is Flashing not in progre
ページ5に含まれる内容の要旨
Flashing WAN port is transferring or receiving data. On USB modem is connected USB Off USB modem is not connected LNK/ACT Flashing USB modem is transferring or receiving data. On LAN port is connected. LAN 1-4 Off LAN port is not connected. LNK/ACT Flashing LAN port is transferring or receiving data. Section 2 Configuring the Router Step 1 Open the web browser (Internet Explorer or Mozilla Firefox) from the computer that is wired to the Router, type 192.16
ページ6に含まれる内容の要旨
Step 3 Click Setup Wizard on the left menu.
ページ7に含まれる内容の要旨
Step 4 Configure the Time Zone Settings of the Router. Click Next. Step 5 Select WAN type by which Internet service you are using. This guide will provide instructions on these WAN types: 3G/3.5G, Cable, and DSL.
ページ8に含まれる内容の要旨
3G/3.5G Click on 3G/3.5G if you are connecting to Internet through a 3G USB modem. When the 3G/3.5G detailed settings come up, enter the Internet connection parameters if it is required by your wireless 3G Internet Service Provider. There are 2 types of Services: CDMA2000 or 3G/3.5G Only (UMTS/HSPA/HSDPA). You may try both service types if you are not sure which one your USB modem uses. Click Next. Note: The setting shown above is for Verizon Wireless USB720 3G Modem. Cabl
ページ9に含まれる内容の要旨
DSL For DSL users, your Internet type is either Dynamic IP or PPPoE. If you are not sure which one you have, it is suggested to select PPPoE xDSL for your WAN type, and if you cannot connect to the Internet after the Setup Wizard finished, go through the Setup Wizard again and select Cable Modem. Otherwise, you can call your ISP to confirm which Internet type you have. Option 1: PPPoE Settings Click on PPPoE xDSL for your WAN type. Enter your user name and password provided by y
ページ10に含まれる内容の要旨
Note: Depending on the ISP, you may need to include the domain name with your username. Example: username@sbcglobal.net Option 2: Dynamic IP Settings Click on Cable Modem for your WAN type. When the Dynamic IP settings come up, leave click Clone MAC and click Next. Step 6 Keep the default SSID (wireless network name) or change it to a desired name, so you can always recognize your wireless network with it. Click Next.
ページ11に含まれる内容の要旨
Step 7 Set up Wireless Security for your router. WPA2(AES) is the most secured encryption mode for general users. WEP is the most common encryption but the least secured. It is recommended to use WPA2 (AES) for your wireless security if all wireless devices on your network can support this mode. WPA2(AES) Select WPA pre-shared key for Encryption.
ページ12に含まれる内容の要旨
WPA Unicast Cipher Suite: Select WPA2(AES) Pre-Shared Key Format: Select Passphrase Pre-shared Key: Enter a key between 8 to 63 characters (alphanumeric, case sensitive). This is the security key for your wireless network Click OK to save the settings. WEP Select WEP for Security Mode.
ページ13に含まれる内容の要旨
• Key Length: Select 64-bit or 128-bit • Key Format: Select Hex or ASCII • Default Tx Key: Select Key 1 • Encryption Key 1: If you selected 64-bit key length and ASCII key format, enter 5 alphanumeric characters. If you selected 128-bit key length and ASCII key format, enter 13 alphanumeric characters. If you selected 64- bit key length and HEX key format, enter 10 hexadecimal characters (0~9, A~F) for Key Setting. If you selected 128-bit key length and HEX key format, enter 26 hexadecima
ページ14に含まれる内容の要旨
If either section has valid IP addresses being assigned, the router is connected to the Internet. Section 3 Connecting to the Router Wirelessly You must configure your wireless computer in order to establish a wireless connection to the router. In this section, you can find the instructions of how to connect to the router wirelessly with your Vista computer. You can also refer to the manual of your wireless network card regarding how to connect to a router wireless
ページ15に含まれる内容の要旨
Step 1 Click on this icon on the task bar of your desktop, then click on Wireless networks are available. Step 2 Click on the wireless network you want to connect to and click Connect.
ページ16に含まれる内容の要旨
Step 3 Enter the Security key you configured for the Router (see Step 8 in Section 2). Click Connect. Step 4 Click on Close. Now the wireless connection has been established successfully with the Router.
ページ17に含まれる内容の要旨
Section 4 (Optional) Connecting to the Router with Easy Setup Button The AR660W3G Airlink101 Wireless N 3G/3.5G Mobile Router has a Easy Setup Button built-in which allows you to connect your wireless computer with the router easily and safely. Your wireless adapter must support this feature (WiFi Protected Setup™) as well. If not, you will need to set up the wireless security manually and you can skip this section. In the instructions below, we are going to use the Airlink1
ページ18に含まれる内容の要旨
You will see this window pops up on the monitor: Step 3 Within the following 2 minutes, push the Easy Setup Button on the Router. The WLAN LED on the Router will stay solid green instead of blinking. Step 4 The Router will now start to synchronize the security settings with the wireless adapter. When you see a similar window as below, the connection has been established.
ページ19に含まれる内容の要旨
Section 5 Troubleshooting If you have trouble connecting to the Internet with the Cable/DSL modem, try the following steps: Step 1 Power off the Cable/DSL modem, router, and computer and wait for 5 minutes. Step 2 Turn on the Cable/DSL modem and wait for the lights on the modem to settle down. Step 3 Turn on the router and wait for the lights on the router to settle down. Step 4 Turn on the computer. Step 5 Log in to the router and you will see the Internet Connection St
ページ20に含まれる内容の要旨
Step 6 Verify that the Internet IP Address, Subnet Mask, and Default Gateway have valid numbers assigned to them (instead of all 0’s). If you have trouble connecting to the Internet with the 3G/3.5G USB modem, there are few things your can try: 1. Make sure your 3G/3.5G modem is compatible with AR660W3G Wireless N 3G/3.5G Router. Please check the compatibility list at www.airlink101.com. 2. Make sure the 3G/3.5G USB modem works when it is directly connected to your computer 3. Make
