ページ1に含まれる内容の要旨
ページ2に含まれる内容の要旨
Vigor2750 Series High Speed VDSL2 Router User’s Guide Version: 1.0 Firmware Version: V1.4.0 Date: 26/10/2010 ii Vigor2750 Series User’s Guide
ページ3に含まれる内容の要旨
Copyright Information Copyright Copyright 2010 All rights reserved. This publication contains information that is Declarations protected by copyright. No part may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language without written permission from the copyright holders. Trademarks The following trademarks are used in this document: Microsoft is a registered trademark of Microsoft Corp. Windows, Windows 95, 98, Me, NT, 2000, XP, Vi
ページ4に含まれる内容の要旨
European Community Declarations Manufacturer: DrayTek Corp. Address: No. 26, Fu Shing Road, HuKou County, HsinChu Industrial Park, Hsin-Chu, Taiwan 303 Product: Vigor2750 Series Router DrayTek Corp. declares that Vigor2750 Series of routers are in compliance with the following essential requirements and other relevant provisions of R&TTE Directive 1999/5/EEC. The product conforms to the requirements of Electro-Magnetic Compatibility (EMC) Directive 2004/108/EC by complying with the r
ページ5に含まれる内容の要旨
T Ta ab blle e o of f C Co on nt te en nt ts s 1 Preface ...............................................................................................................1 1.1 Web Configuration Buttons Explanation ................................................................................. 1 1.2 LED Indicators and Connectors .............................................................................................. 2 1.2.1 For Vigor2750 ...........................................
ページ6に含まれる内容の要旨
3.3.7 Bind IP to MAC ............................................................................................................... 54 3.4 NAT ....................................................................................................................................... 56 3.4.1 Hardware NAT................................................................................................................ 56 3.4.2 Open Ports..............................................................
ページ7に含まれる内容の要旨
4 Admin Mode Operation ....................................................................................... 119 4.1 VDSL....................................................................................................................................119 4.1.1 VDSL Status ................................................................................................................. 120 4.1.2 VDSL Setup ..................................................................................
ページ8に含まれる内容の要旨
4.9.4 Station List .................................................................................................................... 196 4.9.5 Access Point Discovery ................................................................................................ 197 4.9.6 WMM Configuration...................................................................................................... 198 4.9.7 WDS......................................................................................
ページ9に含まれる内容の要旨
6.2 Checking If the Network Connection Settings on Your Computer Is OK or Not ................. 250 6.3 Pinging the Router from Your Computer............................................................................. 252 6.4 Checking If the ISP Settings are OK or Not........................................................................ 253 6.5 Forcing Vigor Router into TFTP Mode for Performing the Firmware Upgrade ................... 254 6.6 Backing to Factory Default Setting If Necess
ページ10に含まれる内容の要旨
ページ11に含まれる内容の要旨
1 Preface Preface The Vigor2750 series are the routers with high speed in data transmission through DSL port and LAN ports. With the development of NGN (Next Generation Network), you may recently hear the news about FTTx deployment in your local area or even have already subscribed the unbundling last mile service (e.g. VDSL2) from local ITSP for FTTx. As adopting FTTx, the main question for end users is whether your legacy router could fully utilize its bandwidth or not. DrayTek la
ページ12に含まれる内容の要旨
1.2 LED Indicators and Connectors 1.2 LED Indicators and Connectors Before you use the Vigor router, please get acquainted with the LED indicators and connectors first. 1 1..2 2..1 1 F Fo or r V Viig go or r2 27 75 50 0 LED Status Explanation ACT Blinking The router is powered on and running (Activity) normally. Off The router is powered off. HPA On Hardware NAT is enabled. (Hardware Off Hardware NAT is disabled. Packet Accelerate) DSL On The DSL port is connected. Blinking
ページ13に含まれる内容の要旨
Interface Description Factory Reset Restore the default settings. Usage: Turn on the router (ACT LED is blinking). Press the hole and keep for more than 5 seconds. When you see the ACT LED begins to blink rapidly than usual, release the button. Then the router will restart with the factory default configuration. PWR Connector for a power adapter. Power Switch. I / O Vigor2750 Series User’s Guide 3
ページ14に含まれる内容の要旨
1 1..2 2..2 2 F Fo or r V Viig go or r2 27 75 50 0n n LED Status Explanation ACT Blinking The router is powered on and running (Activity) normally. Off The router is powered off. HPA On Hardware NAT is enabled. (Hardware Off Hardware NAT is disabled. Packet Accelerate) DSL On The DSL port is connected. Blinking The router is ready. (Slowly) Blinking The connection is training. (Quickly) On The port is connected with 1000Mbps. LAN1/2/3/4 (Green) Blinking The data is transm
ページ15に含まれる内容の要旨
Interface Description Factory Reset Restore the default settings. Usage: Turn on the router (ACT LED is blinking). Press the hole and keep for more than 5 seconds. When you see the ACT LED begins to blink rapidly than usual, release the button. Then the router will restart with the factory default configuration. PWR Connector for a power adapter. Power Switch. I / O Vigor2750 Series User’s Guide 5
ページ16に含まれる内容の要旨
1 1..2 2..3 3 F Fo or r V Viig go or r2 27 75 50 0V Vn n LED Status Explanation ACT Blinking The router is powered on and running (Activity) normally. Off The router is powered off. HPA On Hardware NAT is enabled. (Hardware Off Hardware NAT is disabled. Packet Accelerate) DSL On The DSL port is connected. Blinking The router is ready. (Slowly) Blinking The connection is training. (Quickly) On The port is connected with 1000Mbps. LAN1/2/3/4 (Green) Blinking The data is tr
ページ17に含まれる内容の要旨
Interface Description Phone2/Phone1 Connector of analog phone for VoIP communication. Factory Reset Restore the default settings. Usage: Turn on the router (ACT LED is blinking). Press the hole and keep for more than 5 seconds. When you see the ACT LED begins to blink rapidly than usual, release the button. Then the router will restart with the factory default configuration. PWR Connector for a power adapter. Power Switch. ON/OFF Vigor2750 Series User’s Guide 7
ページ18に含まれる内容の要旨
1.3 Hardware Installation 1.3 Hardware Installation Before starting to configure the router, you have to connect your devices correctly. 1. Connect the DSL interface to Internet with a VDSL2 line cable. 2. Connect one port of 4-port switch to your computer with a RJ-45 cable. This device allows you to connect 4 PCs directly. 3. Connect Phone port to a conventional analog telephone. 4. Connect detachable antennas to the router for Vigor2750 series (n model). 5. Connect one end of the
ページ19に含まれる内容の要旨
S St ta an nd d IIn ns st ta alllla at tiio on n The Vigor2750 must be placed erectly. Therefore you have to install a stand onto the router to make it standing firmly. Please follow the figures listed below to finish the installation. Vigor2750 Series User’s Guide 9
ページ20に含まれる内容の要旨
1.4 Printer Installation 1.4 Printer Installation You can install a printer onto the router for sharing printing. All the PCs connected this router can print documents via the router. The example provided here is made based on Windows XP/2000. For Windows 98/SE/Vista, please visit www.draytek.com. Before using it, please follow the steps below to configure settings for connected computers (or wireless clients). 1. Connect the printer with the router through USB/parallel port. 2. Open
