ページ1に含まれる内容の要旨
™
HomeLink Series
Phoneline 10M
Cable/DSL Router
Use this guide to install: HPRO200
User Guide
ページ2に含まれる内容の要旨
COPYRIGHT & TRADEMARKS Copyright © 2001 Linksys, All Rights Reserved. HomeLink is a registered trademark of Linksys. Microsoft, Windows, and the Windows logo are registered trademarks of Microsoft Corporation. All other trademarks and brand names are the property of their respective proprietors. LIMITED WARRANTY Linksys guarantees that every HomeLink Phoneline 10M Cable/DSL Router is free from physical defects in material and workmanship under normal use for one (1) year from the date of p
ページ3に含まれる内容の要旨
HomeLink™ Series Phoneline 10M Cable/DSL Router Table of Contents Troubleshooting 30 Common Problems and Solutions 30 Introduction 1 Frequently Asked Questions 32 The Linksys HomeLink Phoneline 10M Cable/DSL Router 1 Features 1 Appendix 36 Package Contents 2 How to Ping Your ISP’s E-mail & Web Addresses 36 System Requirements 2 Installing the TCP/IP Protocol 38 Twisted Pair Cabling 41 Getting to Know the HomeLink Phoneline Crimping Your Own Network Cables 42 10M Cable/DSL Router 3 The HomeLink P
ページ4に含まれる内容の要旨
Phoneline 10M Cable/DSL Router HomeLink™ Series Introduction The Linksys HomeLink™ Phoneline 10M Cable/DSL Router The HomeLink™ Phoneline 10M Cable/DSL Router provides the perfect solu- tion for connecting to high-speed broadband Internet through your existing telephone lines. This HomeLink™ Phoneline 10M Cable/DSL Router from Linksys acts as the only externally recognized Internet gateway on your Local Area Network (LAN) and can be configured to regulate internal users’ access to the Internet
ページ5に含まれる内容の要旨
HomeLink™ Series Phoneline 10M Ethernet Bridge Crossover Switch The Crossover Switch (X II) toggles the LANport Getting to Know the HomeLink between crossover mode (X) and straight-through mode (II). If you are connecting the Router directly to a com- puter or to an Uplink port, choose crossover (X). For any- Phoneline 10M Cable/DSL thing else, choose straight-through (II). The HomeLink Phoneline Router’s Rear Panel Ports Router Power Connect your power adapter to your HomeLink Phoneline Rou
ページ6に含まれる内容の要旨
Linksys HomeLink™ Series Phoneline 10M Cable/DSL Router The HomeLink Phoneline Router’s Front Panel LEDs The WAN Indicators Link Green. The Link LEDilluminates when a successful connection is made between the HomeLink Phoneline Router and your Broadband device or network. Act Green. The Act LEDflickers when the HomeLink Phoneline Router is sending or receiving data over the broadband port. Power The Power LED will light up when the HomeLink Diag Red. The Diag LED illuminates when the HomeLink Ph
ページ7に含まれる内容の要旨
HomeLink™ Series Phoneline 10M Cable/DSL Router Connecting the HomeLink Phoneline Router to Your Network Using the HomeLink Phoneline The following instructions will have your HomeLink Phoneline Router up and running in minutes. 10M Cable/DSL Router N No otte e: Power everything off before connecting PCsto the Installation Overview HomeLink Phoneline Router. If both the PC and the Router are powered on when the initial connection is made, the network may Since the HomeLink Phoneline 10M Cable/DS
ページ8に含まれる内容の要旨
HomeLink™ Series Phoneline 10M Cable/DSL Router Daisy-chaining a HomeLink Network Resetting the HomeLink Phoneline Router Daisy-chaining your HomeLink PCs and peripherals can create a simple net- If your network connections begins acting erratically, you may want to reset the work that acts in the same way an Ethernet network acts on your PC's desktop. Homelink Phoneline Router. While Ethernet networks usually revolve in a star topology around a hub or To reset your Homelink Phoneline Router,
ページ9に含まれる内容の要旨
HomeLink™ Series Phoneline 10M Cable/DSL Router N No otte e:: If you have previously enabled an Internet Sharing Proxy Service on any of your PCs, you must disable it Configuring Your Ethernet now. Network with the HomeLink • If you are running Netscape Navigator: Click E Ed diitt >> P Pr re effe er re en nc ce e >> A Ad dv va an nc ce ed d >> P Pr ro ox xiie es s> and click D Diir re ec ctt C Co on nn ne ec cttiio on n tto o tth he e IIn ntte er rn ne ett. Phoneline 10M Cable/DSL Router •
ページ10に含まれる内容の要旨
HomeLink™ Series Phoneline 10M Cable/DSL Router LAN IP Address These values refer to 7. Unless you already have a DHCP server on your internal network, choose N No otte e:: If you have an existing DHCP server on your LAN and you don’t your internal network settings. Unless Enable from the DHCP Server field. By choosing Enable, you will con- wish to use the HomeLink Phoneline you have specific internal needs, there figure the HomeLink Phoneline Router to automatically assign IP address- Router a
ページ11に含まれる内容の要旨
HomeLink™ Series Phoneline 10M Cable/DSL Router 3. In the Configuration window, select the TCP/IP protocol line that has 6. Windows will ask you to restart the PC. Click the Yes button. been associated with your network card/adapter. If there is no TCP/IP line listed, refer to the Appendix to install the TCP/IP Protocol now. Repeat steps 1-6 for each PC on your network. When all of your PCs are configured, the HomeLink Phoneline Router Setup and Installation is complete. If you would like, you m
ページ12に含まれる内容の要旨
HomeLink™ Series Phoneline 10M Cable/DSL Router Setup The HomeLink Phoneline 10M On the following pages you will find brief descriptions of each utility web-page and each page’s more important functions. More detailed explanations and instructions can be found by clicking each page’s Help button. To apply any Cable/DSL Router’s Web-based settings you’ve altered on any page, click the Apply button, then click Continue. To clear any values you’ve entered on any page, click Cancel. Utility Quick &
ページ13に含まれる内容の要旨
HomeLink™ Series Phoneline 10M Cable/DSL Router • LAN IP Address and Subnet Mask The IP Address and Subnet Mask of Password the HomeLink Phoneline Router as it is seen on the internal LAN. The default value is 192.168.1.1 for IP and 255.255.255.0 for Subnet Mask. • WAN IP Address and Subnet Mask The IP Address and Subnet Mask of the HomeLink Phoneline Router as seen by external users on the Internet (including your ISP). If set to Obtain an IP address automatically, these val- ues are assigned b
ページ14に含まれる内容の要旨
HomeLink™ Series Phoneline 10M Cable/DSL Router • WAN These fields display the HomeLink Phoneline Router’s IP Address, Status Subnet Mask and Gateway IP, as seen by external users on the Internet. • DNS (Domain Name Server) IP Address This field shows the IP Address of the DNS currently being used. Multiple DNS IP settings are common. The first available DNS entry is used in most cases. DHCP This screen provides the current status of the device. All of the information pro- vided is read-only. A
ページ15に含まれる内容の要旨
HomeLink™ Series Phoneline 10M Cable/DSL Router • DHCP Client Table Click on the Client Table button to show the current 4. Enter the HomeLink Phoneline Router’s administration password into the DHCP Client information. (This information is stored in temporary memo- Password Confirm box. ry, so the list of clients could disappear.) 5. Click the Browse button and find the firmware upgrade file that you down- Help loaded from the Linksys website. Double-click the upgrade file. 6. Click the Upgrad
ページ16に含まれる内容の要旨
HomeLink™ Series Phoneline 10M Cable/DSL Router Forwarding is generally used to set up a webserver, ftp server, or e-mail server Block WAN Request on your network. To add a server using Forwarding: • By enabling the Block WAN Request feature, you can prevent your network 1. Enter the port number used by the server. On the same line, enter the IP from being pinged, or detected, by other Internet users. The Block WAN Address of the server that you want the Internet users to be able to access. Req
ページ17に含まれる内容の要旨
HomeLink™ Series Phoneline 10M Cable/DSL Router To set up Dynamic Routing: To create a static route entry: 1. Choose the correct working mode. Gateway Mode should be used if your 1. Select Static Route Entry from the drop down list. The HomeLink HomeLink Phoneline Router is hosting your network's connection to the Phoneline Router supports up to 20 static route entries. Internet. Router Mode should be selected if the HomeLink Phoneline Router exists on a network with other routers. 2. Enter th
ページ18に含まれる内容の要旨
HomeLink™ Series Phoneline 10M Cable/DSL Router DMZ Host Troubleshooting Common Problems and Solutions This section provides possible solutions to problems regarding the installation and operation of the HomeLink Phoneline Router. Read below description to solve your problems. If you can’t find an answer here, check the Linksys web- site at www.linksys.com. 1. I Can’t connect to the HomeLink Phoneline Router. • The HomeLink Phoneline Router is properly installed, all connections are OK, and it
ページ19に含まれる内容の要旨
HomeLink™ Series Phoneline 10M Cable/DSL Router • If using Windows 95, 98, or ME, check the TCP/IP setup on the client • If you are connecting to a cable modem, try plugging the cable modem side. Run "winipcfg" by clicking on the Start button, selecting Run, typ- into the HomeLink Phoneline Router’s uplink port rather than a 10BaseT ing “winipcfg” into the empty field and pressing the Enter key. The PC port. should have an IP address of 192.168.1.xxx ("xxx" is from 2 to 254.) • If all else fails
ページ20に含まれる内容の要旨
HomeLink™ Series Phoneline 10M Cable/DSL Router Does the HomeLink Phoneline Router support any operating system other than Web page hangs, corrupt downloads, or nothing but junk characters are being dis- Windows 95, 98, Millennium, NT, or 2000? Yes, but Linksys does not, at this played on the screen. What do I need to do? Force your NIC to 10Mbps or time, provide technical support for setup, configuration or troubleshooting of half-duplex mode, and turn off the "Autonegotiate" feature of your NI
