ページ1に含まれる内容の要旨
IP Router
QUICK START GUIDE
Part Number: 002-0118-0180
Product Release: 1.8
May 2004
ページ2に含まれる内容の要旨
Copyright 2004 Carrier Access Corporation. All rights reserved. The information presented in this manual is subject to change without notice and does not represent a commitment on the part of Carrier Access Corporation. The hardware and software described herein are furnished under a license or non-disclosure agreement. The hardware, software, and manual may be used or copied only in accordance with the terms of this agreement. It is against the law to reproduce, transmit, transcribe, store
ページ3に含まれる内容の要旨
QUICK START GUIDE In this Guide Installation Basic Setup PPP Internet Connection and Public IP Address Routing Frame Relay Internet Connection and Public IP Address Routing Internet Connection using PPP, NAT/PAT and Firewall Filters Internet Connection using NAT and Static NAT Addresses Back-to-Back with PPP Back-to-Back with Multi-Link PPP Back-to-Back with Frame Relay
ページ4に含まれる内容の要旨
Quick Start Guide Installation Installation Installation of the router card into the chassis. Unit can be on or off Router card will work in any slot Slide card into slot until fully seated Router has completed it’s boot cycle when CRD light is solid The following setups are all executed with CLI NOTE: Configuration can be done with the following CLI commands or with the Router Menu-Driven Software. Basic Setup Command Description set {ds0-addr} type data Confirm DS0 is set to type dat
ページ5に含まれる内容の要旨
Quick Start Guide PPP Internet Connection and Public IP Address Routing PPP Internet Connection and Public IP Address Routing Router in Slot 1 ISP Router that provides the Internet connection. Command Description set clock1 a:1 Set primary master transmit clock source set 1 default Set Router to default settings disconnect a:1 Disconnect all connections to the T1 on the Controller (slot a) disconnect 1 Disconnect all connections to the router in slot 1 set a:1:all type data Set the T1-1 of t
ページ6に含まれる内容の要旨
Quick Start Guide Frame Relay Internet Connection and Public IP Address Routing Frame Relay Internet Connection and Public IP Address Routing Router in Slot 1 ISP Router that provides the Internet connection. Command Description set clock1 a:1 Set primary master transmit clock source set 1 default Set Router to default settings disconnect a:1 Disconnect all connections to the T1 on the Controller (slot a) disconnect 1 Disconnect all connections to the router in slot 1 set a:1:all type data Se
ページ7に含まれる内容の要旨
Quick Start Guide Internet Connection using PPP, NAT/PAT and Firewall Filters Internet Connection using PPP, NAT/PAT and Firewall Filters Router in Slot 1 ISP Router that provides the Internet connection. Router with NAT/PAT and Firewall Filters. Command Description set clock1 a:1 Set primary master transmit clock source set 1 default Set Router to default settings disconnect a:1 Disconnect all connections to the T1 on the Controller (slot a) disconnect 1 Disconnect all connections to the r
ページ8に含まれる内容の要旨
Quick Start Guide Internet Connection using PPP, NAT/PAT and Firewall Filters Command Description add 1 "wan1" firewall 2 pass Adds a Firewall rule to the WAN. Where inout nolog ping xxx.xxx.xxx.xxx is the host’s IP address at the far 192.168.21.14/32 end that will be able to ping or telnet to the router. xxx.xxx.xxx.xxx/32 0.0.0.0/0 will allow any other host at the far end to ping and/or telnet to the router. add 1 "wan1" firewall 3 pass Adds a Firewall rule to the WAN. inout nolog ping 0.
ページ9に含まれる内容の要旨
Quick Start Guide Internet Connection using NAT and Static NAT Addresses Internet Connection using NAT and Static NAT Addresses Router in Slot 1 ISP Router that provides the Internet connection. Router with NAT and Static NAT addresses. Command Description set clock1 a:1 Set primary master transmit clock source set 1 default Set Router to default settings disconnect a:1 Disconnect all connections to the T1 on the Controller (slot a) disconnect 1 Disconnect all connections to the router in s
ページ10に含まれる内容の要旨
Quick Start Guide Internet Connection using NAT and Static NAT Addresses Command Description add 1 "wan1" static nat address Add static NAT bi-directional mapping to wan1 192.168.21.15 216.174.44.233 add 1 "wan1" static nat address Add static NAT bi-directional mapping to wan1 192.168.21.16 216.174.44.234 add 1 "wan1" static nat address Add static NAT bi-directional mapping to wan1 192.168.21.17 216.174.44.235 set 1:1:1 encapsulation fr Set the encapsulation on trunk 1 to Frame Relay set 1 lmi a
ページ11に含まれる内容の要旨
Quick Start Guide Back-to-Back with PPP Back-to-Back with PPP The following configuration will set up two Adit 600 Routers back-to-back with PPP. 24 DS0s Boulder Denver wan1: PPP or Frame Relay 1.1.1.1/24 2.2.2.1 / 24 Static Routes IP Boulder Router in Slot 1 Command Description set 1 default Set Router to default settings disconnect a:1 Disconnect all connections to the T1 on the Controller (slot a) disconnect 1 Disconnect all connections to the router in slot 1 set a:1:all type data Set the
ページ12に含まれる内容の要旨
Quick Start Guide Back-to-Back with PPP Denver Router in Slot 1 Command Description set 1 default Set Router to default settings disconnect a:1 Disconnect all connections to the T1 on the Controller (slot a) disconnect 1 Disconnect all connections to the router in slot 1 set clock1 a:1 Set primary master transmit clock source set a:1:all type data Set the T1-1 of the Controller, Type to Data connect a:1:all 1:1:1 Connect all of T1-1 to the Router that is in slot 1 rename 1 "LocalUnit" "Denver"
ページ13に含まれる内容の要旨
Quick Start Guide Back-to-Back with Multi-Link PPP Back-to-Back with Multi-Link PPP The following configuration will set up two Adit 600 Routers back-to-back with Multi- Link PPP. Boulder Router in Slot 1 Command Description set 1 default Set Router to default settings disconnect a:1 Disconnect all connections to the T1 on the Controller (slot a) disconnect 1 Disconnect all connections to the router in slot 1 set a:1:all type data Set the T1-1 of the Controller, Type to Data connect a:1:all 1:
ページ14に含まれる内容の要旨
Quick Start Guide Back-to-Back with Multi-Link PPP Denver Router in Slot 1 Command Description set 1 default Set Router to default settings disconnect a:1 Disconnect all connections to the T1 on the Controller (slot a) disconnect 1 Disconnect all connections to the router in slot 1 set clock1 a:1 Set primary master transmit clock source set a:1:all type data Set the T1-1 of the Controller, Type to Data connect a:1:all 1:1:1 Connect all of T1-1 to the Router that is in slot 1 connect a:2:all 1:
ページ15に含まれる内容の要旨
Quick Start Guide Back-to-Back with Frame Relay Back-to-Back with Frame Relay The following configuration will set up two Routers back-to-back with Frame Relay. Denver Boulder 1.1.1.1/24 1.1.1.1/24 24 DS0s Boulder Denver wan1: PPP or Frame Relay 1.1.1.1/24 2.2.2.1 / 24 Static Routes IP Boulder Router in Slot 1 Command Description set clock1 internal Set primary master transmit clock source set 1 default Set Router to default settings disconnect a:1 Disconnect all connections to the T1 on the
ページ16に含まれる内容の要旨
Quick Start Guide Back-to-Back with Frame Relay Denver Router in Slot 3 Command Description set 3 default Set Router to default settings disconnect a:1 Disconnect all connections to the T1 on the Controller (slot a) disconnect 3 Disconnect all connections to the router in slot 1 set clock1 a:1 Set primary master transmit clock source set a:1:all type data Set the T1-1 of the Controller, Type to Data connect a:1:all 3:1:1 Connect all of T1-1 to the Router that is in slot 1 rename 3 "LocalUnit"
