ページ1に含まれる内容の要旨
COLOR VIDEO CAMERA
INSTRUCTIONS
ADC770
For Customer Use:
Enter below the Serial No. which is
located on the body. Retain this
information for future reference.
Model No. ADC770
Serial No.
LWT0188-001A-H
E-1
e01_adc770(01_05)e.p65 1 5/10/04, 10:37 AM
DIGITAL
BF LOOK
∞
ページ2に含まれる内容の要旨
These are general IMPORTANT SAFEGUARDS and certain items may not apply to all appliances. IMPORTANT SAFEGUARDS 1. Read all of these instructions. 2. Save these instructions for later use. 3. All warnings on the product and in the operating instructions should be adhered to. 4. Unplug this appliance system from the wall outlet before cleaning. Do not use liquid clean- ers or aerosol cleaners. Use a damp cloth for cleaning. 5. Do not use attachments not recommended by the appliance manufacturer as
ページ3に含まれる内容の要旨
13. Follow all warnings and instructions marked on the appliance. 14. Do not overload wall outlets and extension cords as this can result in fire or electric shock. 15. Never push objects of any kind into this appliance through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the appliance. 16.Do not attempt to service this appliance yourself as opening or removing covers may expose you to
ページ4に含まれる内容の要旨
Safety Precautions Due to design modifications, data given in this FOR USA AND CANADA instruction book are subject to possible change without prior notice. CAUTION RISK OF ELECTRIC SHOCK WARNING: DO NOT OPEN TO REDUCE THE RISK OF FIRE OR CAUTION:TO REDUCE THE RISK OF ELECTRIC ELECTRIC SHOCK, DO NOT SHOCK. DO NOT REMOVE COVER (OR EXPOSE THIS APPLIANCE TO RAIN BACK). NO USER-SERVICEABLE PARTS INSIDE.REFER SERVICING TO OR MOISTURE. QUALIFIED SERVICE PERSONNEL. AVERTISSEMENT: The lightning flash wis
ページ5に含まれる内容の要旨
Thank you for purchasing this product. (These instrustions are for ADC770) Before beginning to operate this unit, please read the instruction manual carefully in order to make sure that the best possible performance is obtained. CONTENTS INTRODUCTION Features ...............................................................................................................................6 Operating Precautions .........................................................................................
ページ6に含まれる内容の要旨
INTRODUCTION Features A new DSP (Digital Signal Processor) Before starting an important recording, features a Extended Dynamic Range be sure to perform a test recording in (ExDR) and enables to shoot both bright order to confirm that a normal and dark locations. recording is possible. We do not accept liability for the loss of The use of a new CCD with a SENSE UP a recording in the case of it becoming (X32) function realized the minimum impossible to record due to a problem luminous flux
ページ7に含まれる内容の要旨
Operating Precautions ● To save energy, when it is not being used ● Observe the following when carrying out turn the system’s power off. camera maintenance. ● This camera has been designed for indoor •Turn the power OFF before proceeding use. When you use it outdoor, be sure to to carry out maintenance. use a housing and the like. If it is contaminated seriously, clean the ● Do not install or use the camera in the contaminated part with a cloth (or a following places. tissue) which has been soak
ページ8に含まれる内容の要旨
INTRODUCTION Controls, Connectors and Indicators 2 1 3 4 5 7 6 Lens mount Camera-mounting bracket 1 4 This means to attach the lens. The bracket has been attached on the This is applicable to both the C-mount bottom of the camera before shipment. It lenses and CS-mount lenses. can also be attached on the top according to the circumstance. Backfocus adjustment ring 2 To re-attach the bracket use the threaded Adjusting the back focus during lens holes at the top, with the camera installation. moun
ページ9に含まれる内容の要旨
!#$ @ SET CAMERA SETUP EXT TERM-OFF ON AWC MENU INT/GL LL % NOT USED ^ IRIS VIDEO DC 8 90 Cover [SET/AWC] Set. Auto White Control 8 12 The cover opens if it is pulled to the left Button while being pushed. SET: Press this button to display a sub- menu. [VIDEO/DC] Iris Selector Switch 9 ( Page 23) This is set according to the type of lens AWC: If this button is kept pressed for when an automatic iris control lens is more than 1 second, a one-push- used. auto-white-balance function works VIDEO: I
ページ10に含まれる内容の要旨
INTRODUCTION Controls, Connectors and Indicators (Continued) [ , , , ] Up-and-down, left-and- 13 right Button These buttons select items on the menu screen and change a set value. ( Page 23) [EXT.TERM-ON/OFF] Terminal On/Off 14 Switch of External Synchronization Signal This is a terminating ON/OFF switch for the external synchronization input signal. When this is switched ON, termination is executed via a 75 Ω resistor. ON: terminates at 75 Ω. OFF: does not terminate at 75 Ω. (ON: At time of fa
ページ11に含まれる内容の要旨
& * + - REMOTE 12 CLASS 2 ONLY(U TYPE) ISOLATED POWER ONLY (E TYPE) AUX GND Y/C OUT ¤ ( SYNC IN VIDEO OUT SEE INST- RUCTION POWER MANUAL ⁄ ) [DC 12V, AC 24V] Power input terminals [POWER] Power indicator lamp 17 21 To input DC 12V or AC 24V power. This lamp lights when power is supplied to the camera. [AUX, GND] Auxiliary Output Terminals 18 If any change occurs in the area that was [SYNC IN] Sync signal input connector 22 set on the MOTION DETECT screen, these This BNC connector accepts the inp
ページ12に含まれる内容の要旨
Av Pk L H ALC LEVEL CONNECTION/INSTALLATION Procedures Execute connection/installation according to the procedures described below. Turn OFF the power supply to all equipment to be used before making carefully. 4.Setting the switches 6.Back focus adjustment ( Page 17) ( Page 21) SET CAMERA SETUP AWC EXT TERM-OFF ON MENU INT/GL LL NOT USED IRIS VIDEO DC 5.Lens adjustment 7.Auto white balance ( Page 20) control adjustment ( Page 22) 1.Mounting the lens 3.Mounting the camera ( Page 14)
ページ13に含まれる内容の要旨
DC 12V/AC 24V power supply 2.Connections To alarm terminals ( Page 15) such as switches REMOTE 1 2 CLASS 2 ONLY(U TYPE) ISOLATED POWER ONLY (E TYPE) AUX GND Y/C OUT Genlock sync signal generator SYNC IN VIDEO OUT SEE INST- RUCTION POWER MANUAL Monitor E-13 e02_adc770(06_22)e.p65 13 5/10/04, 10:41 AM DC12V AC24V
ページ14に含まれる内容の要旨
CONNECTION/INSTALLATION Mounting the lens Mount the lens according to the procedures described below. 1. Before mounting a lens, check whether it is a C-mount or CS-mount lens. To change the mounting method, loosen the back-focus locking screw (M 2.6) using a Phillips head screwdriver, turn the back-focus adjusting ring with your fingers or the screwdriver and change the mounting method. Dimension (b) of the lens shown in the illustration must be as shown in the table below. If (b) exceeds the v
ページ15に含まれる内容の要旨
Connections on the back Connect the DC 12 V or the AC 24 V power Power supply supply to the DC 12V/AC 24V terminals. To prevent connection errors or a cable disconnection, we recommend the use of lug plates for the connections. The following table shows the connection distances and connection cables provided REMOTE 1 2 that 2-conductor VVF cables (vinyl-insulated CLASS 2 ONLY(U TYPE) ISOLATED POWER ONLY vinyl sheath cables) are used. (E TYPE) GND Maximum extension 328 feet 853 feet 1345 feet 1
ページ16に含まれる内容の要旨
CONNECTION/INSTALLATION Connections on the back (Continued) Genlock connection With some systems, when the external sync signal is a composite video or black burst sig- nal genlocking by applying an external sync input requires the horizontal phase (H PHASE) and colour phase (SC COARSE) to be adjusted. MEMO • Genlocking is not possible with a signal containing too much jitter, such as a VCR or videodisc playback signal. Setting the swaitches E-16 e02_adc770(06_22)e.p65 16 5/10/04, 10:41 AM
ページ17に含まれる内容の要旨
Setting the switches EXT TERM-OFF ON SET CAMERA INT/GL LL SETUP EXT TERM-OFF ON AWC MENU INT/GL LL NOT USED NOT USED IRIS VIDEO DC Select the synchronization method of the camera image. Set the switch on all cameras to LL (Line Lock) and match with the V. PHASE. ( Page 26.) E-17 e02_adc770(06_22)e.p65 17 5/24/04, 11:46 am
ページ18に含まれる内容の要旨
CONNECTION/INSTALLATION Mounting the camera When mounting the camera on a fixer, pan/ tilt, etc., use the camera mounting screw hole Camera mounting located on the camera-mounting bracket. screw Camera-mounting bracket CAUTION: Use the screw with a length shorter than 7mm from a camera-mounting face. MAX. 7mm Furthermore, make use of the rotation Rotation prevention hole prevention hole to prevent the camera from falling and securely mount the camera. Special precautions must be taken for mounti
ページ19に含まれる内容の要旨
Installation of camera q • Mounting from the bottom This camera is originally designed to be mounted from the bottom, as shown q. VIDEO IRIS The hole is standard photographic pan- DC head screw size (1/4-20 UNC). Example the Fixing unit or Pan/Tilt unit. • Mounting from the top Remove the CAMERA MOUNTING BRACKET from the bottom of the camera by removing two fixing screws as shown w. Attach the CAMERA MOUNTING BRACKET to the top, then mount the camera on the Fixing Unit as shown e. Make sure that
ページ20に含まれる内容の要旨
CONNECTION/INSTALLATION Lens adjustment Connect the camera according to the connection method, turn it on, display an image on the monitor, and check the image. The camera has been factory-adjusted to the best position, but it may need to be adjusted according to the object conditions or combination of lenses. If the image is unnatural, adjust it as follows: (Also read the instruction manual of the lens.) LEVEL adjustment • LEVEL adjustment Monitor screen LEVEL turning direction Too bright Count
