ページ1に含まれる内容の要旨
DIAMOND PRO
OPERATING MANUAL
DIAMOND 8.1 PRO
DIAMOND 8.2 PRO
DIAMOND 8.1 PRO ACTIVE
DIAMOND 8.2 PRO ACTIVE
ページ2に含まれる内容の要旨
!Warning – read all operating and service instructions that accompany this appliance! !Varning – läs alla användar- och serviceinstruktioner som medföljer enheten! !Atenção - leia todas as instruções de manutenção e de operação que acompanham este aparelho! !AVVERTENZA – Leggere attentamente le istruzioni per il funzionamento e la manutenzione fornite con l'unità! !Aviso: Lea todas las instrucciones de funcionamiento y de mantenimiento que se adjuntan a este aparato!Vaara – lue kaikki laitteen
ページ3に含まれる内容の要旨
Contents: Page 1: Using your Reference Monitor Use of a subwoofer Page 2: Use with CRT displays 5.1 Monitoring Stereo Near Field Monitoring Set-up Page 3: 5.1 Set-up Equalisation System Drivers Page 4: Crossover Cables and Connections A/C Connection Amplifier/s Installation and Application Positioning and Mounting Page 5: EQ-LF Bass Filter Portrait or Horizontal Mounting Console Top Mounting Page 6: Stand Mounting Center speaker Mounting and Positioning Controls and Indicators: Rear and Front P
ページ4に含まれる内容の要旨
Wharfedale Diamond 8.1 Pro, 8.2 Pro and Pro-Active Near Field Reference Monitors The function of a Reference Monitor Loudspeaker System is to provide an accurate sonic reference for the operator/engineer thus enabling value decisions to be made in the recording and mixing process. The purpose of these devices is not simply to sound exciting, or impressive - only to give an accurate and clean representation of the original sources and recording devices used. This must be done with the minimum
ページ5に含まれる内容の要旨
wavelength is around 28ft (8.5m). It is quite possible that at these wavelengths from a single source/woofer both your ears could be in a phase hole. The room may be rattling and shaking, but you would not hear the direct sound only its effect on the space. The opposite is also true. The room and woofer interaction could generate a standing wave that would give up to 6dB of build up at your ears. Thus great care should be taken in placement to find the best location for the speaker. If possib
ページ6に含まれる内容の要旨
nominal central aim point is recommended. Again, experiment and find a comfortable median position. Height placement should ideally not be from below, nor typically too high. Be sensitive to early reflections from control surfaces. Careful placement can reduce the destructive effects of reflections, diffraction etc. Be aware of placements that can excite cavity resonances, and look for symmetry from left to right and across the main three screen channels. 5.1 set-up: The Left and Right
ページ7に含まれる内容の要旨
make the higher frequencies at crossover, but their light weight means the cone can break up when asked to stop and start over 4,000 times a second at typical crossover frequencies, with resultant “cone cry”, Crossover: 8.1 Pro: internal passive crossover, 2.2kHz 8.1 Pro: internal passive crossover, 2.0kHz 8.1 Pro-Active: internal active crossover, 2.0kHz 8.2 Pro-Active: internal active crossover, 1.9kHz The inherent quality and correctness of the design of the Diamond components means that si
ページ8に含まれる内容の要旨
importantly the heat sink assembly. Make sure the heat sink has sufficient clearance to allow reasonable airflow. This will, to some extent, be dependant on the power levels and duty cycles under which one is operating the system. EQ-LF: In the real world, as opposed to the theoretical, loudspeakers operate and interact with the space in which they are used. It is important to understand the low frequency reinforcement that occurs as a result of the relationship of the speaker to walls etc. At
ページ9に含まれる内容の要旨
Stand Mounting: Depending on the application stand mounting in (near to) free space is one of the most neutral positions for monitors. Of course it is not always possible to take advantage of the isoalation from floor, wall and countertop effects that stands can allow. But combinations of short stand and console can be used to advantage. Center Speaker Mounting and Positioning: Ideally the center speaker is just that; mounted in the center! However, the type and size of display can seriously e
ページ10に含まれる内容の要旨
8.1 Pro 8.2 Pro Models Type 2 WAY 2 WAY Usable frequency response 50Hz-24kHz 45Hz-24kHz Peak SPL @ 1m, short term IEC noise source 106dB 108dB Sensitivity 86dB 86dB Power Handling (Watts) 100 W 100 W Recommended amp power 30-150W 30-200W Impedance nominal 4Ω 4Ω Drive Units 5"LF, 1" HF 6.5" LF, 1" HF System Magnetic Shielding Yes Yes Crossover frequency 2.2K 2.2K Input connectors 1 x phono speakon type /jack combo Input connectors (active) 1 x phono (unbalanced) 1 x XLR-1/4 jack combo balanced
ページ11に含まれる内容の要旨
Diamond 8.1 Pro Active free air with/without bass cut Diamond 8.2 Pro Active free air with/without bass cut. 8
ページ12に含まれる内容の要旨
WHARFEDALE PROFESSIONAL IAG HOUSE, SOVEREIGN COURT, ERMINE BUSINESS PARK, HUNTINGDON, PE29 6XU, UK www.wharfedalepro.com 911.388
