ページ1に含まれる内容の要旨
Customer Order # 11992L
Manufacturer Part # 11992LB Rev. 2
ページ2に含まれる内容の要旨
This manual contains proprietary information of Zebra Technologies Corporation. It is intended solely for the information and use of parties operating and maintaining the equipment described herein. Such proprietary information may not be used, reproduced, or disclosed to any other parties for any other purpose without the expressed written permission of Zebra Technologies Corporation.
Continuous improvement of products is a policy of Zebra Technol
ページ3に含まれる内容の要旨
Zebra XiIII-Series User’s Guide iii
ページ4に含まれる内容の要旨
iv Zebra XiIII-Series User’s Guide
ページ5に含まれる内容の要旨
Hello! .......................................................................................................................1 Unpacking and Inspection........................................................................................2 Reporting Damage ..............................................................................................2 Storage ............................................
ページ6に含まれる内容の要旨
System Considerations .......................................................................................... 21 Interfaces .......................................................................................................... 21 Data Specifications........................................................................................... 21 Cabling Requirements ....................................................................
ページ7に含まれる内容の要旨
Lubrication.............................................................................................................71 Fuse Replacement ..................................................................................................71 Adjustments ...........................................................................................................73 Toggle Positioning............................................................................................73 Printhead Pressure Adjus
ページ8に含まれる内容の要旨
viii Zebra XiIII-Series User’s Guide
ページ9に含まれる内容の要旨
Thank you for purchasing this high-quality Zebra XiIII™-Series printer, manufactured by the industry leader in quality, service, and value — Zebra Technologies Corporation. For over 25 years, Zebra has provided customers with the highest caliber of products and support. This manual provides all of the information you need to operate your printer. ® The ZPL II Programming Guide Volume I and Volume II (part # 45540L) shows you how to create the perfect label format for
ページ10に含まれる内容の要旨
Carefully unpack and inspect the printer for possible damage incurred during shipment. Check all exterior surfaces. Raise the media access door and inspect the media compartment. In case shipping is required, save the carton and all packing material. Contact your authorized Zebra reseller for instructions.
If you discover shipping damage: Immediately notify and file a damage report with the shipping company. Zebra Technologies Corporation is n
ページ11に含まれる内容の要旨
Since print quality is affected by media and ribbon, printing speeds, and printer operating modes, it is very important to run tests for your applications. We STRONGLY RECOMMEND the use of Zebra Technologies Corporation-brand supplies for continuous high-quality printing. A wide range of paper, polypropylene, polyester, and vinyl stock has been specifically engineered to enhance the printing capabilities of the printer and to ensure against premature printhe
ページ12に含まれる内容の要旨
Figure 1 outlines the basic components of your printer. However, depending on the options you have selected, your printer may look slightly different. Figure 1 4Zebra XiIII-Series User’s Guide
ページ13に含まれる内容の要旨
This chapter of the user’s guide is so important that we’ve printed it on a different color paper! That way, it is easy for you to find when you must calibrate (set up) the printer for your particular application. To calibrate the printer. To verify that the printer is properly set up by printing a test label. NOTE: This procedure must be performed when the printer is first installed or when it cannot properly detect the top of the label. To calibrate the
ページ14に含まれる内容の要旨
! " Non-continuous web media (refer to Figure 2) refers to individual labels that are separated by a gap, notch, or hole. When you look at the media, you can tell where one label ends and the next one begins. Figure 2 6Zebra XiIII-Series User’s Guide
ページ15に含まれる内容の要旨
Non-continuous black mark media has black marks printed on the back that indicate the start and end of each label (refer to Figure 3). Figure 3 Continuous media (refer to Figure 4) is one uninterrupted roll of material that allows the image to be printed anywhere on the label. Figure 4 Zebra XiIII-Series User’s Guide 7
ページ16に含まれる内容の要旨
#
# In Tear-Off mode, each label (or a strip of labels) can be torn off after it is printed. In Peel-Off mode, backing material is peeled away from the label as it is printed. After this label is removed from the printer, the next one is printed. In Cutter mode, the printer automatically cuts the label after a specified number of labels has been printed. In Rewind mode, the media and backing are rewound onto a core as the labels are printed. 8Zebra XiIII-Series User
ページ17に含まれる内容の要旨
$
# Figure 5 illustrates one method of media loading. For more detailed instructions, as well as information about how to load the different types of media and the various printing modes, refer to the instructions that begin on page 27. Figure 5 Zebra XiIII-Series User’s Guide 9
ページ18に含まれる内容の要旨
# % The correct positioning of the media sensors is important — it can make the difference between a perfect label and a call to Technical Support!
The web or gap sensor, better known as the “transmissive sensor,” detects the gap between labels. The transmissive sensor actually consists of two sections: a light source (the lower media sensor) and a light sensor (the upper media sensor). The media passes between the two. The upper media sensor m
ページ19に含まれる内容の要旨
!"
# $
Refer to Figure 6. (For clarity, not all printer parts are shown.) 1. Remove the ribbon (if it is installed). 2. Locate the upper media sensor. The upper media sensor “eye” is directly below the adjustment screw head. 3. Slightly loosen the upper media sensor adjustment screw (use a Phillips-head screwdriver). 4. Using the tip of the screwdriver, slide the upper sensor along the slot to the desired position. 5. Secure the upper media sensor adjustment screw.
ページ20に含まれる内容の要旨
!"
% $
Position the lower media sensor (refer to Figure 7) by sliding it in its slot until it is positioned under the upper media sensor. Figure 7 The black mark sensor is in a fixed position and enabled via the front panel (refer to “Configuring the Printer” on page 15 for details). 12 Zebra XiIII-Series User’s Guide
