ページ1に含まれる内容の要旨
HW173
HSG1044
ページ2に含まれる内容の要旨
User’s Manual Before operating the monitor, please read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio fre
ページ3に含まれる内容の要旨
User’s Manual RECYCLING INFORMATION We, the Hanns.G care very much about our environment protection strategy and firmly believe that it helps us have healthier earth via appropriate treatment and recycling of industrial technology devices at the end-of-life. These devices contain recyclable materials, which can be re-decomposed and re-integrated into brand-new marvels. On the contrary, other material can be classified to hazardous and poisoned substances. We strongly encourage you to conta
ページ4に含まれる内容の要旨
User’s Manual TABLE OF CONTENTS SAFETY NOTICE ......................................................................................................5 PRECAUTIONS.....................................................................................................5 SPECIAL NOTES ON LCD MONITORS ..........................................................6 BEFORE OPERATING THE MONITOR ...............................................................7 FEATURES..........................................
ページ5に含まれる内容の要旨
User’s Manual SAFETY NOTICE 1. The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 2. Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits. 3. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment. It is the responsibilities of the user to correct such interference. WARN
ページ6に含まれる内容の要旨
User’s Manual SPECIAL NOTES ON LCD MONITORS The following symptoms are normal with LCD monitor and do not indicate a problem. Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears. You may find slightly uneven brightness on the screen depending on the desktop pattern you use. The LCD screen has effective pixels of 99.99% or more. It may include blemishes of 0.01% or les
ページ7に含まれる内容の要旨
User’s Manual BEFORE OPERATING THE MONITOR FEATURES 17” Wide screen TFT Color LCD Monitor Crisp, Clear Display for Windows RecommendedResolutions: 1440 X 900@60Hz ® EPA ENERGY STAR ErgonomicDesign Space Saving, Compact Case Design CHECKING THE CONTENTS OF THE PACKAGE The product package should include the following items: LCD Monitor Screen Base Cables and User manual DVI-D Cable (dual input mode Power Cord VGA Cable optional) User’s manual Warranty card 7
ページ8に含まれる内容の要旨
User’s Manual INSTALLATION INSTRUCTIONS Install Remove Figure.1. Installing and Removing the Base INSTALLATION: 1. Align the monitor with the opening in the base. 2. Note that the longer section of the base points forward. 3. Snap the monitor into its base. A clear click sound will affirm that the base is connected correctly. 4. Verify that the monitor is securely attached to the base by looking at the bottom of the base and making sure that the clips are fully engaged in the base. REMOV
ページ9に含まれる内容の要旨
User’s Manual MAKING CONNECTIONS CONNECTING TO A PC Turn off your computer before performing the procedure below. 1. Connect one end of the VGA cable to the back of the monitor and connect the other end to the computer’s D-Sub port. 2. Connect one end of DVI-D cable (Dual input mode optional) to the back of the monitor and connect the other end to the computer’s DVI-D port. 3. Plug one end of the AC power cord to the LCD monitor’s AC input socket, and the other end to the Wall outlet. 4.
ページ10に含まれる内容の要旨
User’s Manual ADJUSTING THE VIEWING ANGLE For optimal viewing it is recommended to look at the full face of the monitor, and then adjust the monitor’s angle to your own preference. Hold the stand so you do not topple the monitor when you change the monitor’s angle. You are able to adjust the monitor’s angle from -4 to 20 . Monitor Angle Figure.3. NOTES: Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen. Be careful not to place fingers o
ページ11に含まれる内容の要旨
User’s Manual OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off. The other control buttons are located on the front panel of the monitor (See Figure 4). By changing these settings, the picture can be adjusted to your personal preference. The power cord should be connected. Connect the Signal cable from the monitor to the VGA card. Press the power button to turn on the monitor. The power indicator will light up. Figure.4. Control Panel Butt
ページ12に含まれる内容の要旨
User’s Manual FRONT PANEL CONTROL PowerButton: Press this button to switch ON/OFF monitor’s power. Power Indicator: Green — Power On mode. Orange — Power Saving mode. MENU / RETURN: 1. Turn the OSD menu on/off or return to the previous menu. 2. Exit OSD menu when in volume OSD status. Adjust < >: 1. Navigate through adjustment icons when OSD is ON or adjust a function when function is activated. i Button: 1. Press the i button to select the input signal type. (There are VGA, DVI, YpbP
ページ13に含まれる内容の要旨
User’s Manual HOW TO ADJUST A SETTINGS BRIGHTNESS/CONTRAST Adjust the brightness value of the display according to your preference. Select BRIGHTNESS option to adjust the BRIGHTNESS brightness value. Adjust the contrast value of the display according to your CONTRAST preference. Select CONTRAST option to adjust the contrast value. Optimal setting for high contrast images or videos. The dark and light areas of the image are automatically detected, and the X-CONTRAST contrast is enhanced
ページ14に含まれる内容の要旨
User’s Manual Select the H-POSITION option to shift the screen image to the H-POSITION left or right. Enter the option and adjust the level. [For VGA only] Select the V-POSITION option to shift the screen image up or V-POSITION down. Enter the option and adjust the level. [For VGA only] Select the CLOCK option to reduce the vertical flicker of CLOCK characters on the screen. Enter the option and adjust the level. [For VGA only] Select the PHASE option to reduce the horizontal flicker
ページ15に含まれる内容の要旨
User’s Manual Select the FACTORY RESET option to reset to the monitor’s FACTORY RESET default setting. This will erase the current settings. Enter the option and select On or Off. Display Horizontal frequency/Vertical frequency/Resolution INFORMATION information. 15
ページ16に含まれる内容の要旨
User’s Manual PLUG AND PLAY Plug & Play DDC2B Feature This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities. The DDC2B is a bidirectional data channel based on the I²C protocol. The host can request EDID information over the DDC2B channel. THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF
ページ17に含まれる内容の要旨
User’s Manual TECHNICAL SUPPORT (FAQ) Q & A FOR GENERAL PROBLEMS PROBLEM & QUESTION POSSIBLE SOLUTION *Check if the Power Switch is in the ON position. Power LED is not on *Power Cord should be connected. *Check if the PC system is Plug & Play compatible. *Check if the Video Card is Plug & Play compatible. No Plug & Play *Check if any plug pins on the VGA or DVI-D connector are bent. The display is too dark or too *Adjust the Contrast and Brightness Controls. bright. Picture bounces or
ページ18に含まれる内容の要旨
User’s Manual ERROR MESSAGE & POSSIBLE SOLUTIONS CABLE NOT CONNECTED: 1. Check that the signal-cable is properly connected, If the connector is loose, tighten the connector’s screws. 2. Check the signal-cable’s connection pins for damage. INPUT NOT SUPPORT: Your computer has been set to unsuitable display mode, set the computer to display mode given in the following table. RECOMMENDED AND SUPPORTED TIMING MODE: (Analog / Digital mode) HORIZONTAL VERTICAL MODE RESOLUTION FREQUENCY (KHz) FR
ページ19に含まれる内容の要旨
User’s Manual 28 1400×1050 @60Hz 65.317 59.978 55.469 59.901 29 1440×900 @60Hz 55.935 59.887 30 1440×900 @60Hz 31 1440×900 @75Hz 70.635 74.984 19
ページ20に含まれる内容の要旨
User’s Manual APPENDIX SPECIFICATIONS Driving system TFT Color LCD LCD Panel Size 17” Pixel pitch 0.255mm(H) x0.255mm(V) H-Frequency 24KHz –80KHz Video V-Frequency 55Hz– 75Hz Display Colors 16.2M Colors Max. Resolution 1440 x 900 @75Hz TM Plug & Play VESA DDC2B ON Mode 36W ® EPA ENERGY STAR Power Saving Mode 2W OFF Mode 1W VGA Input Terminal DVI-D (optional) Hor. : 367.2.mm Maximum Screen Size Ver. : 229.5mm Power Source 100~240VAC±10%,50±3Hz,60±3Hz Operating Temp: 5° to 35°C Environm
