ページ1に含まれる内容の要旨
ページ2に含まれる内容の要旨
Copyright This publication, including all photographs, illustrations and software, is protected under international copy- right laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author. © Copyright 2011 Disclaimer The information in this document is subject to change without notice. The manufacturer makes no repre- sentations or warranties with respect to the contents hereof and specifically dis
ページ3に含まれる内容の要旨
IN3118HD User’s Manual Important Safety Information Important: It is strongly recommended that you read this section carefully before using the projector. These safety and usage instructions will ensure that you enjoy many years of safe use of the projector. Keep this manual for future reference. Symbols Used Warning symbols are used on the unit and in this manual to alert you of hazardous situations. The following styles are used in this manual to alert you to important information. N
ページ4に含まれる内容の要旨
Preface Projector Installation Notice Place the projector in a horizontal position The tilt angle of the projector should not exceed 15 degrees, nor should the projector be installed in any way other than the desktop and ceiling mount, otherwise lamp life could decrease dramatically. Allow at least 50 cm (19.69 inch) clearance around the exhaust vent. (19.69 inch) (19.69 inch) (19.69 inch) (3.94 inch) (11.81 inch) (19.69 inch) Ensure that the intake vents do no
ページ5に含まれる内容の要旨
IN3118HD User’s Manual Replacing the Lamp Replacing the lamp can be hazardous if done incorrectly. See Replacing the Projection Lamp on page 33 for clear and safe instructions for this procedure. Before replacing the lamp: Unplug the power cord. Allow the lamp to cool for about one hour. Cleaning the Projector Unplug the power cord before cleaning. See Cleaning the Projector on page 36. Allow the lamp to cool for about one hour. Regulatory Warnings Before installing and using the p
ページ6に含まれる内容の要旨
Preface Table of Contents GETTING STARTED........................................................................................................................................................... 1 PACKING CHECKLIST........................................................................................................................................................... 1 VIEWS OF PROJECTOR PARTS.............................................................................................
ページ7に含まれる内容の要旨
IN3118HD User’s Manual PROJECTION DISTANCE VS. PROJECTION SIZE.................................................................................................................... 43 Projection Distance and Size Table......................................................................................................................... 43 TIMING MODE TABLE...........................................................................................................................................
ページ8に含まれる内容の要旨
Safety Booklet DLP Projector – User’s Manual GETTING STARTED Packing Checklist Carefully unpack the projector and check that the following items are included: DLP PROJECTOR REMOTE CONTROL CARRY CASE CD-ROM (BATTERIES NOT INCLUDED) (THIS USER’S MANUAL) VGA CABLE POWER CORD REGISTRATION CARD (VARIES PER COUNTRY) SAFETY BOOKLET QUICK START GUIDE WARRANTY BOOKLET Contact your dealer immediately if any items are missing, appear damaged, or if the unit
ページ9に含まれる内容の要旨
IN3118HD User’s Manual Views of Projector Parts Front-right View 1 2 34 5 6 7 ITEM LABEL DESCRIPTION SEE PAGE: Elevator button Push to release elevator foot 1. 10 2. Elevator foot Adjusts level of projector Lens Projection Lens 3. IR receiver Receives the remote control IR signal 4. 6 Focus ring Focuses the projected image 5. 11 Zoom ring Enlarges the projected image 6. See Top view—On-screen Display (OSD) but- Function keys 7. 3 tons and LEDs. Important: Ventilati
ページ10に含まれる内容の要旨
Re-sync DLP Projector – User’s Manual Top view—On-screen Display (OSD) buttons and LEDs 1 2 3 4 5 12 6 Menu 7 Enter 11 10 8 9 ITEM LABEL DESCRIPTION SEE PAGE: Solid Power On / Standby Green Power LED 1. Off Power Off (AC Off) Solid Red The lamp is powered on. 2. Lamp LED Flashing The lamp is warming up or cooling down. Red (see LED Error Messages on page 38) Temp LED Solid Red Error code (see LED Error Messages on page 38) 3. Turn the projector On or Off. 4. 9 (Power but
ページ11に含まれる内容の要旨
IN3118HD User’s Manual Rear view ITEM LABEL DESCRIPTION SEE PAGE: 1. AC IN Connect the POWER CABLE 9 Connect the USB CABLE from a computer 2. (USB) (used for presentation slide control with the projector remote) S-VIDEO IN Connect the S-VIDEO CABLE from a video device 3. 4. VIDEO IN Connect the COMPOSITE CABLE from a video device VGA OUT Connect the RGB CABLE to an external monitor 5. VGA IN Connect the RGB CABLE from a computer 6. 7. H
ページ12に含まれる内容の要旨
DLP Projector – User’s Manual Bottom view ITEM LABEL DESCRIPTION SEE PAGE: Leveling foot Rotate leveling foot to adjust angle position. 1. 10 Only use with an InFocus ceiling mount system (p/n PRJ-MNT-UNIV). 2. Ceiling support holes See your InFocus dealer or go to www.infocusstore.com. Elevator foot drops down when elevator button is Elevator foot 3. pushed. 10 Elevator button Push to release elevator foot. 4. Note: When installing, ensure that you use only UL Listed c
ページ13に含まれる内容の要旨
IN3118HD User’s Manual Remote Control Parts Important: 1. Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency fluo- rescent lights can disrupt remote control operation. 2. Be sure nothing obstructs the path between the remote control and the projector. If the path be- tween the remote control and the projector is obstructed, you can bounce the signal off certain reflective surfaces such as projector screens. 3. The buttons and keys on the proj
ページ14に含まれる内容の要旨
DLP Projector – User’s Manual ITEM LABEL DESCRIPTION SEE PAGE: Power ON Turn the projector on 1. 9 LED indicator Only lights when the remote keys are pressed 2. 3. Display Mode Choose a suitable preset mode for usage environment Contrast Display the Contrast setting bar and use the right and left keys to adjust 4. Display the Brightness setting bar and use the right and left keys to ad- 5. Brightness just. When the OSD is displayed, this button navigates to the
ページ15に含まれる内容の要旨
IN3118HD User’s Manual SETUP AND OPERATION Inserting the Remote Control Batteries Remove the battery compartment 1. cover by sliding the cover in the di- rection of the arrow. Insert the batteries (not included) as 2. shown in the illustration. Replace the cover. 3. Caution: 1. Only use AA batteries (Alkaline batteries are recommended). 2. Dispose of used batteries according to local ordinance regulations. 3. Remove the batteries when not using the projector for pr
ページ16に含まれる内容の要旨
DLP Projector – User’s Manual Starting and Shutting down the Projector Connect the power cord to the pro- 1. jector. Connect the other end to a wall outlet. The POWER LED will be on. Turn on the connected devices. 2. 3. Ensure the POWER LED dis- plays a solid green. Then press the Power ON button on the projector keypad or remote ( ). The projector splash screen displays and connected devices are de- tected. If more than one input device is connected, press the SOURCE
ページ17に含まれる内容の要旨
IN3118HD User’s Manual Adjusting the Projector Level Take note of the following when setting up the projector: • The projector table or stand should be level and sturdy. • Position the projector so that it is perpendicular to the screen. • Remove and discard the foam spacer on the rear leveling foot before adjusting the projec- tion angle. • Ensure the cables are in a safe location. You could trip over them. D A B C To raise the level of the projector, lift the projector [A] and press
ページ18に含まれる内容の要旨
DLP Projector – User’s Manual Adjusting the Zoom ring, Focus and Keystone Use the Zoom control 1. (on the projector only) to resize the projected image and screen size B . Use the Focus control 2. (on the projector only) to sharpen the pro- jected image A . Use the KEYSTONE 3. buttons (on the projec- tor or the remote control) to correct im- age trapezoiding (wider top or bottom). Remote control and OSD panel The keystone control 4. appears on the display. – 11 –
ページ19に含まれる内容の要旨
IN3118HD User’s Manual Adjusting the Volume Press the Volume but- 1. tons (on the projector or the remote control). The volume control appears on the display. Use the Vol +/- buttons 2. (on the projector or the remote control). Press the MUTE button 3. to turn off the audio (This feature is avail- able only on the remote). – 12 –
ページ20に含まれる内容の要旨
DLP Projector – User’s Manual ON-SCREEN DISPLAY (OSD) MENU SETTINGS OSD Menu Controls The projector has an OSD that lets you make image adjustments and change various settings. Navigating the OSD You can use the remote control cursor buttons or the projector keypad to navigate and make changes to the OSD. 1. To enter the OSD, press the MENU button. 2. There are six menus. Press the cur- sor ◄► button to move through the menus. 3. Press the cursor ▲▼ button to move up and down i
