ページ1に含まれる内容の要旨
www.collegehillshonda.com
Accessory Application Publications No.
AII 38215-38958
INSTALLATION
REMOTE ENGINE
2006-2008 CIVIC 2-DOOR
Issue Date
STARTER SYSTEM
INSTRUCTIONS (A/T ONLY)
FEB 2008
PARTS LIST Remote Engine Starter Attachment Kit
P/N 08E92-SNA-100B
Remote Engine Starter Unit Kit
P/N 08E91-E22-100B
Engine starter harness
Transmitter
Control unit
Control unit bracket
Antenna
Relay bracket
3 Black relays (4-pin)
Key ring
Protective tape
18 Wire ties
Engine starter label
Fuse label
Accessory
ページ2に含まれる内容の要旨
www.collegehillshonda.com 7 Foam cushion tapes TOOLS AND SUPPLIES REQUIRED Phillips screwdriver Long blade flat-tip screwdriver Small flat-tip screwdriver 6 mm Hex wrench Flange nut T25 Torx bit 3 mm and 7 mm Drill bit Clip File Ratchet 10 mm Socket Combination wrench Isopropyl alcohol Shop towel Green relay (5-pin) Tape measure Clip remover Diagonal cutters Felt-tip pen Template Center punch Scissors 2 Pairs of needle nose pliers Rubber mallet HDS (Honda Diagnostic System) Masking tape Safety g
ページ3に含まれる内容の要旨
www.collegehillshonda.com Setting the Control Unit SW : 1 RR Junction Unit SW : 2 Trunk or Tailgate 3. Get the control unit. Using a small flat-tip SW : 3 Smart Entry screwdriver, adjust the switches on the control SW : 4 Horn or Buzzer Answer Back unit to the locations shown. Using a isopropyl SW : 5 Trunk Main SW alcohol on a shop towel, clean the area where the SW : 6 Reserve protective tape will attach. Attach the protective tape to the control unit over the switches. NOTE: Removing the vehi
ページ4に含まれる内容の要旨
www.collegehillshonda.com 5. Using the key, unlock the opener. 8. If equipped, remove the driver’s dashboard under cover (turn the knob counterclockwise, and 6. Remove the left front door sill trim (two retaining release two clips and pin). tabs, five clips, and three hooks). 3 HOOKS 5 CLIPS PIN 2 RETAINING TABS DRIVER’S 2 CLIPS DASHBOARD UNDER COVER KNOB FRONT 5202112T LEFT FRONT DOOR SILL TRIM 5202200T 9. Remove the driver’s dashboard lower cover (eight 7. Pull away the weatherstrip, and remov
ページ5に含まれる内容の要旨
www.collegehillshonda.com 10. Lower the tilt lever, and pull the steering wheel 12. Remove the column lower cover (two self-tapping toward you. Insert a long blade flat-tip screwdriver screws and one screw). along the guide of the column lower cover, and pry the retaining tab of the column upper cover. 2 RETAINING TABS Push. COLUMN LOWER COLUMN COVER UPPER COVER 2 HOOKS COLUMN LOWER RETAINING COVER 2 SELF-TAPPING TAB SCREWS SCREW 5308530T TILT LEVER GUIDE LONG BLADE 6608050T FLAT-TIP SCREWDRIVE
ページ6に含まれる内容の要旨
www.collegehillshonda.com 13. If equipped, use a small flat-tip screwdriver to 15. Remove the cap from the left sunvisor (four remove the left and right lens from the map light retaining tabs). console (four retaining tabs for each lens). Remove the two bolts, and then release the map CONNECTOR light console. 4 RETAINING TABS FRONT MAP LIGHT CONSOLE LEFT CAP SUNVISOR TORX 5217030T 4 RETAINING SCREW TABS LENS 16. Remove the left sunvisor (two T25 Torx screws, BOLT and unplug the vehicle connector
ページ7に含まれる内容の要旨
www.collegehillshonda.com 19. Pull away the weatherstrip from the left front pillar Installing the Antenna trim. Remove the left front pillar trim (two clips). 21. Using scissors, cut out the template. TEMPLATE LEFT FRONT 2 CLIPS PILLAR TRIM SCISSORS Cut out. 7503030T WEATHERSTRIP 5202100T 22. Secure the template to the windshield with the tape by aligning it with the edge of the black 20. Remove the clip from the left front pillar trim, and ceramic paint as shown. install a new clip on the lef
ページ8に含まれる内容の要旨
www.collegehillshonda.com 23. Using two pairs of needle-nose pliers, bend the 24. Measure the antenna cable as shown. Attach the antenna plate according to the illustration and three foam cushion tapes to the antenna cable in measurement shown. the measurement shown. ANTENNA ANTENNA FOAM CABLE CUSHION TAPE ANTENNA 15 mm 360 mm (0.6 in.) (14 in.) 8 mm (0.3 in.) 30 mm (1.2 in.) 30 mm (1.2 in.) 6D01240T 25. Using isopropyl alcohol on a shop towel, clean the area where the antenna will attach. Allow
ページ9に含まれる内容の要旨
www.collegehillshonda.com 28. Route the antenna cable under the roof liner 30. Using isopropyl alcohol on a shop towel, clean the towards the driver’s side of vehicle, and down areas where the foam cushion tape will attach. along the vehicle harness. Be careful not to Under the roof liner, secure the antenna cable to crease the roof liner. the roof panel with the two foam cushion tapes (cut one foam cushion tape in half) in the areas shown. ROOF LINER ROOF FOAM CUSHION LINER TAPE (1/2) VEHICLE H
ページ10に含まれる内容の要旨
www.collegehillshonda.com 32. Secure the antenna cable to the vehicle harness Installing the Control Unit Bracket with a wire tie. Secure the wire tie between the 33. Locate the small square hole next to the small vehicle harness branching points. round hole in the dashboard support bracket. Under the dashboard, attach the control unit bracket to the vehicle bracket near the front lower pillar using a flange nut. If the vehicle is equipped WIRE TIE VEHICLE with a moonroof, be careful not to pull
ページ11に含まれる内容の要旨
www.collegehillshonda.com Routing the Engine Starter Harness 36. Route the engine starter harness 7-pin connectors up the steering column and to the ignition switch. 34. Attach the 3A fuse labels to the engine starter Unplug the white vehicle 7-pin connector. Plug the harness fuse case, and the 40A fuse labels to the white engine starter harness 7-pin connectors into fuse block. the white vehicle 7-pin connectors. LAYOUT OF RELAYS WHEN VIEWED FROM FRONT 4-PIN IGNITION RELAY SWITCH (black) VEHICL
ページ12に含まれる内容の要旨
www.collegehillshonda.com 37. Unplug the brown vehicle 7-pin connector, and 38. Disconnect the vehicle 8-pin connector on the rear plug the brown engine starter harness 7-pin of the wiper switch and plug the engine starter connector into the brown vehicle 7-pin connector. harness 8-pin connectors into the vehicle 8-pin connector. NOTICE Make sure that the engine starter harness 7-pin connector (brown) is connected to the vehicle ENGINE STARTER connector and it is locked securely. A loosely HAR
ページ13に含まれる内容の要旨
www.collegehillshonda.com 40. Wrap the vehicle 7-pin connector with one foam 43. At the right of the steering shaft, locate the sub cushion tape, then place the vehicle 7-pin joint box. Using a small flat-tip screwdriver, unplug connector into the gap of the column. the vehicle 6-pin connector from the sub joint box. Plug the engine starter harness 6-pin connectors into the vehicle 6-pin connector and the subjoint VEHICLE 7-PIN box. CONNECTOR (brown) ENGINE STARTER (Squeeze into VIEWED FROM HARN
ページ14に含まれる内容の要旨
www.collegehillshonda.com 46. With driver's dashboard under cover: Measure 47. Secure the engine starter harness to the vehicle the indicated dimension on the instrument panel harness using a wire tie: and mark with a felt-tip pen and a center punch. • With driver's dashboard under cover: Secure in the hole opened in the instrument panel. INSTRUMENT PANEL • Without driver's dashboard under cover: Secure through the existing hole for under cover securing. WIRE TIE View from below 12 mm (0.5 in.)
ページ15に含まれる内容の要旨
www.collegehillshonda.com 49. Disconnect the vehicle 42-pin, 4-pin, and 2-pin 50. Plug the engine starter harness 4-pin and 2-pin connectors. connectors into the fuse box. NOTICE Check that the engine starter harness 4-pin VEHICLE 4-PIN VEHICLE 2-PIN and 2-pin connectors are connected to the fuse box CONNECTOR CONNECTOR and they are locked securely. Loosely connected connectors can cause engine stall during driving. VEHICLE 42-PIN CONNECTOR FUSE BOX FOAM 2-PIN CUSHION FUSE BOX 4-PIN VEHICLE CO
ページ16に含まれる内容の要旨
www.collegehillshonda.com 52. Behind the fuse box, unplug the blue vehicle 23- 54. Install the clip from the engine starter harness to pin connector from the inside of the front lower the fuse box bracket behind the fuse box. pillar, and plug the blue engine starter harness 23- pin connectors into the blue vehicle 23-pin GROUND BOLT connector. If the vehicle 23-pin connector is (Reuse.) difficult to disconnect, perform the work after first FRONT disconnecting the connector on the upper side. FUS
ページ17に含まれる内容の要旨
www.collegehillshonda.com Installing the Control Unit 59. Using isopropyl alcohol on a shop towel, clean the area where the engine starter label will attach. 56. Connect the antenna cable terminal and the engine starter harness 18-pin connector to the control unit. HOOD ANTENNA CABLE TERMINAL (Connect first.) ADHESIVE BACKING ENGINE 6D01421T STARTER LABEL FRONT 60. Attach the engine starter label to the back of the CONTROL hood. UNIT 61. Check that all wire harnesses are routed properly CONTROL
ページ18に含まれる内容の要旨
www.collegehillshonda.com REMOTE ENGINE STARTER REGISTRATION 5. Select Honda Systems, then click the check button. 1. Acquire the PCM code from ISIS. 2. Connect the HDS tester to the OBD II data link connector, then turn the ignition switch to the ON (II) position. 3. Start the HDS, and click the car icon. CAR ICON Select CHECK BUTTON “Honda Systems.” 752503AS 6. Select R/C ENG STARTER and click the check button. 752501AS 4. Input the VIN and other required information into the HDS, then click
ページ19に含まれる内容の要旨
www.collegehillshonda.com 7. A REMARKS message will display. Click the 9. The following message will display: Obtain PCM- check button. code (IMMOBILIZER PCM CODE) from iN. This vehicle’s VIN will be required to obtain the password. (USA). Click the check button. “REMARKS” message “Obtain PCM-code" message CHECK BUTTON 752505AS CHECK BUTTON 752507AS 8. Select REGISTER REMOTE CONTROL ENGINE STARTER UNIT, then click the check button. 10. Input the PCM code, then click the check button. NOTE: To
ページ20に含まれる内容の要旨
www.collegehillshonda.com 11. The following message will display: The registration of the Remote Control Engine Starter Unit has been completed. Click the check button. "Registration" message CHECK BUTTON 752510AS 12. The following message will display: Check that the engine can be started by the Transmitter. Click the check button. "Check that the engine can be started by the Transmitter" CHECK BUTTON 752511AS 13. Perform the function check on page 21, then disconnect the HDS. 20 of 22 AII 38
